Instructions / Assembly

6 Questions or concerns? Visit our website at www.pulsescooters.com for replacement parts and technical support, or call [phone].
Assembly
Battery and Charging
WARNING: Batteries must be fully charged before you ride your electric scooter.
Required components: Battery charger
• Initial battery charge time- 10 hours
• Recharges after initial charge- Up to 8 hours
• When scooter is not in regular use batteries need to be charged on a monthly basis to maximize performance.
MATERIAL.
TITLE.
DWG NO.
REV.
SHEET 1 OF 1
SCALE: 1:10
DO NOT SCALE DRAWING
1. DIMENSIONS APPLY BEFORE PLATING OR COATING.
2. REMOVE ALL BURRS, BREAK SHARP EDGES .
3. ALL APPLICABLE BRAVO STANDARDS AND
SPECIFICATIONS APPLY.
UNLESS OTHERWISE SPECIFIED:
METRIC
THIRD ANGLE PROJECTION
1
0.5
0.25
0.1
1°
X.
X.X
X.XX
X.XXX
ANGULAR
C
SIZE
FINISH.
This document is the property of Bravo. All rights are reserved, including copyrights.
TOLERANCES.
DATE
2010-9-1
DRAWN
Sky Shi
APPR
METRIC_C
COLOR.
BRAVO SPORTS
12801 CARMENITA ROAD
SANTA FE SPRINGS, CA, 90670
USA
SHANGHAI OFFICE:
RM 1501/1508, ORIENT CENTER
699 NANJING ROAD WEST
SHANGHAI, CHINA, 200041
1. To connect battery insert plug A
into plug B .
2. Tuck plugs and wires under frame and into
battery box.
3. Plug the battery charger (C) into a wall
power outlet. The light on the battery charger
housing should illuminate.
4. Plug charger into scooter port (D).
A red LED light on the battery charger
indicates battery is charging and a green
LED light indicates battery is fully charged.
WARNING: Do not use this product for the rst time until
you have charged the battery for at least 10 hours. Failure to
follow these instructions may damage your product and void your
warranty.
Note: Do not store the battery in temperatures above 70˚F (21˚C)
or below 32˚F (0˚C).Note: The charger has a small window with one
LED light that indicates the charge status. Refer to the illustration
on the charger unit for the actual “charging” and “charged” status
indication. Your charger may get warm during use; this is normal
and is no cause for concern.
Note: Batteries must be recharged at least once a month even
when the scooter is not in use. Failure to do so may result in
batteries that will no longer accept a charge.
A
C
B
MATERIAL.
TITLE.
DWG NO.
REV.
SHEET 1 OF 1
SCALE: 1:10
DO NOT SCALE DRAWING
1. DIMENSIONS APPLY BEFORE PLATING OR COATING.
2. REMOVE ALL BURRS, BREAK SHARP EDGES .
3. ALL APPLICABLE BRAVO STANDARDS AND
SPECIFICATIONS APPLY.
UNLESS OTHERWISE SPECIFIED:
METRIC
THIRD ANGLE PROJECTION
1
0.5
0.25
0.1
1°
X.
X.X
X.XX
X.XXX
ANGULAR
C
SIZE
FINISH.
This document is the property of Bravo. All rights are reserved, including copyrights.
TOLERANCES.
DATE
2010-9-1
DRAWN
Sky Shi
APPR
METRIC_C
COLOR.
BRAVO SPORTS
12801 CARMENITA ROAD
SANTA FE SPRINGS, CA, 90670
USA
SHANGHAI OFFICE:
RM 1501/1508, ORIENT CENTER
699 NANJING ROAD WEST
SHANGHAI, CHINA, 200041
MATERIAL.
TITLE.
DWG NO.
REV.
SHEET 1 OF 1
SCALE: 1:10
DO NOT SCALE DRAWING
1. DIMENSIONS APPLY BEFORE PLATING OR COATING.
2. REMOVE ALL BURRS, BREAK SHARP EDGES .
3. ALL APPLICABLE BRAVO STANDARDS AND
SPECIFICATIONS APPLY.
UNLESS OTHERWISE SPECIFIED:
METRIC
THIRD ANGLE PROJECTION
1
0.5
0.25
0.1
1°
X.
X.X
X.XX
X.XXX
ANGULAR
C
SIZE
FINISH.
This document is the property of Bravo. All rights are reserved, including copyrights.
TOLERANCES.
DATE
2010-9-1
DRAWN
Sky Shi
APPR
METRIC_C
COLOR.
BRAVO SPORTS
12801 CARMENITA ROAD
SANTA FE SPRINGS, CA, 90670
USA
SHANGHAI OFFICE:
RM 1501/1508, ORIENT CENTER
699 NANJING ROAD WEST
SHANGHAI, CHINA, 200041
D
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not cause
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
NOTE: This equipment has been tested and
found to comply with the limits for a Class
B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is
no guarantee that interference will not occur
in a particular installation. If this equipment
does cause harmful interference to radio or
television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced
radio/TV technician for help.
WARNING: Any changes or modications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to operate the equipment.