Use and Care Guide
5
Installation Continued
the outlet valve and slowly open the inlet valve fully. Check
the unit for leaks. If you find a leak at the brass end-nut,
tighten the brass end-nut further. If the leak continues,
drain the unit and inspect the quartz O-Ring and quartz
sleeve for proper seal. Once you complete checking the
unit, reassemble O-Ring and tighten brass end-nut.
Repressurize the unit and check again.
U.V. LAMPS:
INSTALLATION OF THE ULTRAVIOLET LAMPS:
**DO NOT PUT POWER ON AT THIS TIME!**
CAUTION: Never operate or look directly at U.V.
lamp outside the disinfection chamber.
Make sure unit is unplugged when installing or servicing
ultraviolet lamp. Avoid allowing fingerprints and other
debris to deposit on UV lamp. Carefully place the lamp
inside the quartz sleeve leaving enough space to connect the
socket connector to the lamp pins. Then gently slide the
brass dust cap over the end nut, securing the lamp and
protecting it from dust.
ULTRAVIOLET LAMP MAINTENANCE
REQUIREMENTS: The U.V. lamp is rated for 9,000
hours of continuous use. After this period of time, the
U.V. lamp has undergone a photochemical change. While
the lamp will not normally be burned out, the lamp quartz
may no longer emit the 254-nm shortwave U.V. to
effectively reduce / inactivate bacteria. Failure to replace
the U.V. lamps every 9,000 hours may cause bacteriological
breakthrough. Should the use of the disinfection unit be
intermittent, in no case should the U.V. lamp be used for
more than 24 months regardless of the number of hours
of operation due to normal shelf life degradation of the
U.V. bulb. Changing the quartz sleeve should be done at
the same time U.V. lamp replacement is scheduled.
It is recommended that your water supply be tested
periodically (yearly) through your local health department
or approved certified laboratory.
Option A
Standard Control Box
& UV Chamber Mounting
Option B
Remote Control Box
& UV Chamber Mounting
With Optional Bracket
Option C
Remote Control Box
& UV Chamber Mounting
With Optional Bracket
Mounting Options:
DO NOT SCALE DRAWING
SHEET 1 OF 1
SCALE:
WEIGHT:
REV
DWG. NO.
SIZE
TITLE
NAME
DATE
MFG APPR.
ENG APPR.
CHECKED
FINISH
MATERIAL
5
4
3
2
1
TDB
DRAWN
A
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
AQUA TREATMENT SERVICES. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
AQUA TREATMENT SERVICES IS
PROHIBITED.
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
.25"
TWO PLACE DECIMAL
.010"
THREE PLACE DECIMAL
.002"
UNLESS OTHERWISE SPECIFIED:
9/15/2016
A
TITLE
DO NOT SCALE DRAWING
SHEET 1 OF 1
SCALE:
WEIGHT:
REV
DWG. NO.
SIZE
TITLE
NAME
DATE
MFG APPR.
ENG APPR.
CHECKED
FINISH
MATERIAL
5
4
3
2
1
TDB
DRAWN
A
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
AQUA TREATMENT SERVICES. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
AQUA TREATMENT SERVICES IS
PROHIBITED.
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
.25"
TWO PLACE DECIMAL
.010"
THREE PLACE DECIMAL
.002"
UNLESS OTHERWISE SPECIFIED:
9/15/2016
A
TITLE
DO NOT SCALE DRAWING
SHEET 1 OF 1
SCALE:
WEIGHT:
REV
DWG. NO.
SIZE
TITLE
NAME
DATE
MFG APPR.
ENG APPR.
CHECKED
FINISH
MATERIAL
5
4
3
2
1
TDB
DRAWN
A
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
AQUA TREATMENT SERVICES. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
AQUA TREATMENT SERVICES IS
PROHIBITED.
DIMENSIONS ARE IN INCHES
TOLERANCES:
FRACTIONAL
.25"
TWO PLACE DECIMAL
.010"
THREE PLACE DECIMAL
.002"
UNLESS OTHERWISE SPECIFIED:
9/15/2016
A
TITLE