Owner's manual

ManualsBrandsQ-Tech ManualsAccessories for electricalQT625L

Q-TECH Corporation - 10150 W. Jefferson Boulevard, Culver City 90232 - Tel: 310-836-7900 - Fax: 310-836-2157 - www.q-tech.com

Q-TECH

CORPORATION

Specification Control Drawing

Scope

Part Number

Applicable Documents

Specifications and Standards

Requirements

General Requirements

Approved Manufacturer

Design and Construction

Outline Dimensions and Terminal Connections

Package Body and Lead Finish

Active Devices

Performance Requirements

Maximum Ratings

Electrical Performance Characteristics and Limits

Delta Limits

Total Dose Radiation Limits

Quality Assurance Provisions

General

Screening Tests

Quality Conformance Inspection

Packaging

Preservation, Packaging and Packing

Notes

Ordering Information

Part Number

Table I. Stability/Temperature Options

Source of Supply

Approved Manufacturer

Table II. Maximum Ratings

Table III. Electrical Performance Characteristics

Figure 1. Package Dimensions and Terminal Connections

QT625L XO DETAIL SPECIFICATION

QT625L XO Detail Specification (Revision F, June 2011)

Table of Contents

Summary of content (6 pages)

PAGE 1
Table of Contents Q-TECH CORPORATION QT625L XO DETAIL SPECIFICATION Specification Control Drawing Scope Scope Part Number Applicable Documents Specifications and Standards Requirements General Requirements Approved Manufacturer Design and Construction Outline Dimensions and Terminal Connections Package Body and Lead Finish Active Devices Performance Requirements Maximum Ratings Electrical Performance Characteristics and Limits Delta Limits Total Dose Radiation Limits Quality Assurance Provisions General S
PAGE 2
REVISIONS REVISION DESCRIPTION DATE - Initial release A Modify tr/tf spec limits to better reflect output buffer drive capability. 2-27-07 APPROVED B Clarify temperature stability definitions, Table I. 3-19-07 C Modify paragraph 3.3.3 for clarification of microcircuit technology, SEL rating 7/17/07 D Change to microcircuit manufacturer, paragraph 3.3.3 8/08/08 E.Jackson E Correction to Figure 1. 5/08/09 C.Hooper F Update paragraph 3.3.3.1. Update Table III and notes to Figure 1.
PAGE 3
THIS DOCUMENT IS CONSIDERED PROPRIETARY TO Q-TECH CORPORATION DO NOT COPY OR DISTRIBUTE WITHOUT Q-TECH CORPORATION APPROVAL 1 SCOPE 1.1 Scope. This specification establishes the detail requirements for hybrid, hermetically sealed, crystal oscillators for use in space flight missions. 1.2 Part number. The part number shall be as specified in Table I herein. 2 APPLICABLE DOCUMENTS 2.1 Specifications and standards.
PAGE 4
THIS DOCUMENT IS CONSIDERED PROPRIETARY TO Q-TECH CORPORATION DO NOT COPY OR DISTRIBUTE WITHOUT Q-TECH CORPORATION APPROVAL 4 QUALITY ASSURANCE PROVISIONS 4.1 General. The quality assurance provisions shall be in accordance with the General Specification with the exceptions, modifications, and additions specified herein. 4.2 Screening tests. The screening tests shall be in accordance with the General Specification. 4.3 Quality Conformance Inspection.
PAGE 5
THIS DOCUMENT IS CONSIDERED PROPRIETARY TO Q-TECH CORPORATION DO NOT COPY OR DISTRIBUTE WITHOUT Q-TECH CORPORATION APPROVAL Parameter Supply voltage Operating temperature Storage temperature Lead solder temperature/time Package thermal resistance TABLE II. MAXIMUM RATINGS Symbol Min VCC 0 TC -55 Tstg -65 Max 7 125 150 250/10 50 θjc Units Volts ºC ºC ºC/seconds ºC/W TABLE Ill. ELECTRICAL PERFORMANCE CHARACTERISTICS ELECTRICAL PARAMETER LIMITS TEST CONDITIONS 2/, 3/ MIN. MAX. UNITS 150 MHz 3.
PAGE 6
THIS DOCUMENT IS CONSIDERED PROPRIETARY TO Q-TECH CORPORATION DO NOT COPY OR DISTRIBUTE WITHOUT Q-TECH CORPORATION APPROVAL NOTES: 1. Dimensions are in inches. 2. Lead numbers are for reference only and are not marked on the unit. 3. All pins with function NC may not be connected as external tie or connections, except they may be tied to Ground. TERMINAL CONNECTIONS TERMINAL NO. 1 2 3 4 5 6 7 8 9 10 CONNECTION N/C N/C N/C N/C N/C N/C N/C N/C N/C GND/CASE TERMINAL NO.