Manual

ManualsBrandsQ-Tech ManualsAccessories for electricalQT88RD

AMSC N/A FSC 5955

INCH-POUND

MIL-PRF-55310/36B

1 February 2013

SUPERSEDING

MIL-PRF-55310/36A

19 April 2010

PERFORMANCE SPECIFICATION SHEET

OSCILLATOR, CRYSTAL CONTROLLED, TYPE 1 (CRYSTAL OSCILLATOR (XO),

1 MHz THROUGH 100 MHz, HERMETIC SEAL, LOW VOLTAGE 1.8V CMOS

This specification is approved for use by all Departments

and Agencies of the Department of Defense.

The requirements for acquiring the product described herein

shall consist of this specification sheet and MIL-PRF-55310.

NOTES:

1. Dimensions are in inches.

2. Metric equivalents are given for general information only.

3. Unless otherwise specified, tolerances are ±.005 (0.13 mm) for three place decimals and ±.02 (0.5 mm) for

two place decimals.

FIGURE 1. Interface and physical dimensions.

Pin number

Function

Enable/Disable

GND

Output

B+

Ltr

Inches

Millimeters

Min

Max

Min

Max

.345 Typ

.355 Typ

8.80 Typ

9.02 Typ

.285 Typ

.295 Typ

7.24 Typ

7.49 Typ

.086

.114

2.18

2.90

.195

.205

4.95

5.20

.025

.040

.635

1.02

---

.320

---

8.13

.232

.248

5.89

6.30

---

.170

---

4.32

.015

.021

0.39

0.53

Summary of content (6 pages)

PAGE 1
INCH-POUND MIL-PRF-55310/36B 1 February 2013 SUPERSEDING MIL-PRF-55310/36A 19 April 2010 PERFORMANCE SPECIFICATION SHEET OSCILLATOR, CRYSTAL CONTROLLED, TYPE 1 (CRYSTAL OSCILLATOR (XO), 1 MHz THROUGH 100 MHz, HERMETIC SEAL, LOW VOLTAGE 1.8V CMOS This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-55310.
PAGE 2
MIL-PRF-55310/36B REQUIREMENTS: Interface and physical dimensions: See figure 1. Mounting: See figure 1. Terminals: See figure 1. -8 Seal: Hermetic in accordance with MIL-PRF-55310, maximum leakage rate 5 x 10 atm cc/s. Weight: 3 grams, maximum. Oscillator: Class 2 or any class 1 or class 3 oscillator meeting all class 2 requirements and verification tests specified herein and in MIL-PRF-55310. Calibration: Manufacturer calibrated.
PAGE 3
MIL-PRF-55310/36B TABLE I. Dash numbers and operating characteristics. Dash number 01 04 11 14 21 24 31 34 41 44 Output frequency range Input current (max) 2/ 1.000 MHz to 15.999 MHz 1.000 MHz to 15.999 MHz 16.000 MHz to 39.999 MHz 16.000 MHz to 39.999 MHz 40.000 MHz to 59.999 MHz 40.000 MHz to 59.999 MHz 60.000 MHz to 84.999 MHz 60.000 MHz to 84.999 MHz 85.000 MHz to 100.00 MHz 85.000 MHz to 100.
PAGE 4
MIL-PRF-55310/36B NOTES: 1. For CCL = 15 pF ±5 percent. 2. For RCL = 10 kΩ ±5 percent. 3. CCL includes scope capacitance. FIGURE 2. Load test circuit. FIGURE 3.
PAGE 5
MIL-PRF-55310/36B Vibration, sinusoidal: In accordance with MIL-PRF-55310 and method 204 of MIL-STD-202. Nonoperating: Test condition G. Operating: Not required. Ambient pressure: Nonoperating: In accordance with MIL-PRF-55310. Operating: Method 105 of MIL-STD-202, test condition C. Exposure time: 5 minutes. Reflow soldering: Reflow soldering of the unit at +230°C ±10°C for 15 seconds shall not degrade the performance.
PAGE 6
MIL-PRF-55310/36B Custodians: Army - CR Navy - EC Air Force - 99 DLA - CC Preparing activity: Army - CR Agent: DLA - CC Review activities: Army - AR, MI, SM Navy - AS, CG, MC Air Force - 19 NASA - NA (Project 5955-2013-004) NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https://assist.dla.mil.