Specification
!
W
W
W
E
E
E
T
T
T
L
L
L
O
O
O
O
O
O
K
K
K
S
S
S
E
E
E
A
A
A
L
L
L
E
E
E
R
R
R
–
–
–
H
H
H
I
I
I
G
G
G
H
H
H
G
G
G
L
L
L
O
O
O
S
S
S
S
S
S
P
P
P
R
R
R
O
O
O
D
D
D
U
U
U
C
C
C
T
T
T
N
N
N
O
O
O
.
.
.
8
8
8
8
8
8
0
0
0
0
0
0
-
-
-
0
0
0
6
6
6
PRODUCT USE
QUIKRETE® Wet Look Sealer – High Gloss is a highly water
resistant clear, glossy coating designed to water proof, seal and
enhance the color of decorative concrete, masonry, pavers, brick
and natural stone surfaces. QUIKRETE® Wet Look Sealer is
UV Resistant.
SIZES
• 1 gal (3.8 L) bottle
FINISHES
• High gloss
COVREAGE
Apply at 200-400 sq ft per gallon (18-37 M2). Coverage will
depend on porosity of surface.
PHYSICAL PROPERTIES
Typical physical properties of QUIKRETE
®
Wet-Look
Sealer are identified in Table 1
TABLE 1 - TYPICAL PHYSICAL PROPERTIES
Solids Content 25% wt.
Drying time
(50-90˚ F / 10-32˚C) Approx. 2 hours
Volatile Organic Compound (VOC) 90 g/L maximum
INSALLATION
PREPARATORY WORK
New concrete: Allow a minimum of 30 days for new concrete to
cure before applying Water-proofing Sealer-Natural Look.
Existing surfaces: Surface must be clean and dry. Oil stains,
dirt and other contaminants must be removed. Use QUIKRETE®
Concrete and Asphalt cleaner (No. 8601) to properly prepare the
surface. Unsound or flaking concrete should be removed or
repaired.
Previously sealed surfaces: Surface must be cleaned, porous
and able to accept additional sealer. Do not use this product on
non-porous, sealed or painted surfaces. To test, place drops of
water on the surface. If the water is absorbed, the surface is
porous enough to accept the sealer.
APPLICATION
QUIKRETE® Wet-Look Sealer-High Gloss is ready-to-use and
can be applied with a roller, brush or a garden sprayer. Apply in
a uniform thickness to obtain coverage of 200-400 sq. ft (18-37
M2) per gallon. Coverage will vary depending on surface texture
and porosity. A second coat can be applied after two hours.
Wipe off excess sealer from surface before it dries. Clean up
with warm, soapy water.
PRECAUTIONS
Do not apply if raining, heavy dew or temperatures below 50˚F
(10˚C) are expected within 24 hours. Do not seal areas prone to
standing water. Keep from freeing. Do not apply more than
recommended amount. Do not recoat.
AVAILABILITY
QUIKRETE® Wet-Look Sealer - High Gloss is available at
leading concrete construction supply houses and distributors.
Contact QUIKRETE® Construction Products representative for
the name of the nearest dealer.
WARRANTY
The QUIKRETE Companies warrant this product to be of
merchantable quality when used or applied in accordance with
the instructions herein. The product is not warranted as suitable
for any purpose or use other than the general purpose for which it
is intended. Liability under this warranty is limited to the
replacement of its product (as purchased) found to be defective,
!
DIVISION 3
PRODUCT DESCRIPTION
QUIKRETE® Wet Look Sealer – High Gloss is a water-based, high gloss, siliconized acrylic
clear sealer designed to water proof, seal and enhance the color of decorative concrete,
masonry, pavers, brick and natural stone surfaces. Wet-look sealer–high gloss repels
water and protects from oil, gasoline, grease, salts, acids, household chemicals, food stains
and is UV resistant. For interior or exterior use.
!
!
Maintenance of Concrete
03 01 00
!