Installation Guide

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
BulbRecommended:
EstimatedAssemblyTime:
Preparation:
(9)CandelabraBase60WMaximum
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomer service for replacement
parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-AME5009IB
For Style AME5009IB
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
Hardware Contents
Shade
x9
AA
BB
CC
DD
EE
FF
II
Crossbar
x1
Lock Washer
x2
Hex Nut
x2
Nipple
x1
Canopy
Chain Loop
x1
Canopy Lock
Ring
x1
Ceiling
Canopy
x1
GG
Fixture Chain
x1
HH
Quick Link
x2
A
STEP 1 Install Crossbar-
A. AA)Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..
Figure 1
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw
AA
Place another Lock
Washer (BB) over the
Nipple (DD) and then
thread the Nipple (DD) into
the Crossbar (AA) until the
Nipple (DD) is about
0.375” above the Crossbar
(AA).
C. Remove the Canopy Lock
Ring (FF) from the Canopy
Chain Loop (EE). Place
the Ceiling Canopy (II)
over the Canopy Chain
Loop (EE) against the
ceiling to determine the
correct position of the
Nipple (DD). Thread the
Canopy Lock Ring onto
the Canopy Chain Loop
(EE). Adjust the Nipple
(DD) to allow the Ceiling
Canopy (II) to rest against
August2014
AA
BB
CC
Step B
Step A
DD
CC
BB
EE
II
FF
D
Socket
Assembly
x1
the ceiling when held in place by the Canopy Lock Ring (FF).
D. Remove the Canopy Lock Ring (FF) and the Ceiling Canopy (II).
Tighten the Hex Nut (CC) against the Crossbar (AA) to secure in
place.
Figure 2
STEP 2 Install Canopy Chain Loop and Nipple-
* Pliers is required for this step.
A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at
least 0.25” from the end. Pass one Lock Washer (BB) over the end
of the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the
Nipple (DD). By using pliers, thread the Hex Nut (CC) against the
Canopy Chain Loop (EE) and hand tighten until snug.
B. Thread another Hex Nut (CC) to the middle of the Nipple (DD).
B
C
Side Arm A
x2
Side Arm B
x2
STEP 3 Attach Side Arms-
A. Attach Side Arms A (B) to the Hooks
on the side of the fixture canopy
and attach Side Arms B (C) to the
Hooks on the upper tier as shown.
Figure 3
B
D
Hook
C
Hook
Upper
Tier
STEP 4 - Install Fixture Chain and Ceiling Canopy
A. Adjust the Fixture Chain (GG) to your desired length by removing
the links if needed.
Pliers is required for this step.
B. With the Fixture Chain (GG) not attached to the Fixture Loop (A) and
the Canopy Chain Loop (EE), pull the supply wires through the
Fixture Chain (GG) alternating links. After the wires are through the
Fixture Chain (GG), pull the Supply Wires and the Ground Wire
*