Installation Guide

2of2
2016 QuoizelInc.
ReleasedDate:2016-08-10
STEP 4 - Install Fixture Chain and Ceiling Canopy
A. Adjust the Fixture Chain (GG) to your desired length by removing
links if needed.
Pliers is required for this step.
B. With the Fixture Chain (GG) not attached to the Fixture Loop and the
Canopy Chain Loop (EE), pull the supply wires through the Fixture
Chain (GG) alternating links. After the wires are through the Fixture
Chain (GG), pull the Supply Wires and the Ground Wire through the
Canopy Lock Ring (FF) and the Ceiling Canopy (II) in order.
C. Attach one end of the Fixture Chain (GG) to the Fixture Loop with
one Quick Link (HH). Lift the fixture and Fixture Chain (GG) up and
attach the other end of the Fixture Chain (GG) onto the Canopy
*
Chain Loop (EE) with another
Quick Link (HH). The fixture will
now hang safely. Close the chain
loop at the Ceiling Canopy Loop
(EE).
D. Feed the Supply Wires and
Ground Wire through the Canopy
Chain Loop (EE) and Nipple (DD)
into the Outlet Box. Cut the wires
leaving Approximately 8” of wire
extending from the Outlet Box.
E.RefertoStep5forwire
connections.
F. Raise the Ceiling Canopy (II) and
Canopy Lock Ring (FF) up the
Fixture Chain (GG) and over the
Canopy Chain Loop (EE). Tighten
the Canopy Lock Ring (FF) onto
the Canopy Chain Loop (EE) until
tight.
Suggested chain length for
Ceiling height :
8’ ceiling : use 6 links of chain and
2 quick links
9’ ceiling : use 16 links of chain
and 2 quick links
10’ ceiling : use 26 links of chain
and 2 quick links
DD
GG
II
EE
FF
HH
HH
Supply
Wires and
Ground Wire
Figure 4
A
Figure 5
STEP 5 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into outlet box.
Note: If the electrical wire is going to be cut shorter than provided
you will need to identify the "L" line wire and the "N" neutral wire
before you cut the excess wire off. One is labeled N and the other
labeled L. To do this separate the "L" line wire and the "N" neutral
wire as far as you need to. Re-label the wire near where you want to
make the cut. Be sure to mark the wire on the side of the fixture and
not on the excess wire being cut and removed.
White wire
from supply
Ribbed side of wire from fixture
identified with the Label “N”
Black wire from
supply (or Red)
Smooth side of wire from fixture
identified with the label “L”
Ground wire
from supply
Ground wire
from fixture
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
Bulb (not
supplied)
Socket
Figure 6
ANA5005K
FINISH: MYSTIC BLACK
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/4"
STEP 6 - Install Candle Covers and Bulb
A. Place Candle Cover (E) and Optional Crystal Candle Cover (D) over
socket.
B. Place Bobeche (C) over Candle Cover (E) and Optional Crystal
C
D
(Step 6 Continued)
Candle Cover (D).
C. Insert bulbs into sockets and
screw snugly into place.
Your fixture is now assembled
and ready to use. Enjoy!
E
23.25” Dia.
24.25”
5.5” Dia.
77” OVERALL
HEIGHT INCLUDES
48” CHAINS AND
(2) QUICK LINKS