Installation Sheet

2of3
2017 QuoizelInc.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
STEP 6 - Install Ring, Shade and Bulb
A. Place the Ring (D) between the support arms and fit the bolts on the
Ring (D) to the holes on the support arms.
B. Place the Shade (E) over the socket and secure with the Socket
Collar (F). Hand tighten until snug.
C. Insert bulbs onto sockets and screw snugly into place.
Your fixture is now assembled and ready to use. Enjoy!
Figure 6
ReleasedDate:2017-09-19
(Step 3 Continued)
thread the Nipple (DD) into
the Crossbar (AA) until the
Nipple (DD) is about 0.375”
above the Crossbar (AA).
C. Remove the Canopy Lock
Ring (FF) from the Canopy
Chain Loop (EE). Place the
Ceiling Canopy (II) over the
Canopy Chain Loop (EE)
against the ceiling to
determine the correct
position of the Nipple (DD).
Thread the Canopy Lock
Ring onto the Canopy
Chain Loop (EE). Adjust the
Nipple (DD) to allow the
Ceiling Canopy (II) to rest
against the ceiling when
held in place by the Canopy
Lock Ring (FF).
D. Remove the Canopy Lock
Ring (FF) and the Ceiling
Canopy (II). Tighten the
Hex Nut (CC) against the
Crossbar (AA) to secure in
place.
AA
BB
CC
Step B
Step A
DD
CC
BB
EE
II
FF
Figure 3
DD
GG
II
EE
FF
HH
HH
Fixture
Loop
Supply
Wires and
Ground Wire
STEP 4 - Install the Fixture Chain and Ceiling Canopy
A. Adjust the Fixture Chain (GG) to your desired length by removing
links if needed.
B. Pull the supply wires through the Fixture Chain (GG) alternating
links. After the wires are through the Fixture Chain (GG), pull the
Supply Wires and the Ground Wire through the Canopy Lock Ring
(FF) and the Ceiling Canopy (II) in order.
C. Attach one end of the Fixture Chain (GG) to the Fixture Loop with
Figure 4
one Quick Link (HH). Lift the
fixture and Fixture Chain (GG) up
and attach the other end of the
Fixture Chain (GG) onto the
Canopy Chain Loop (EE) with
another Quick Link (HH). The
fixture will now hang safely.
D. Feed the Supply Wires and
Ground Wire through the Canopy
Chain Loop (EE) and Nipple (DD)
into the Outlet Box. Cut the wires
leaving approximately 8” of wire
extending from the Outlet Box.
E. Go to Step 5 for wire connections
and follow the directions. Return
to Step F in this step when
complete with Step 5.
F. Raise the Ceiling Canopy (II) and
Canopy Lock Ring (FF) up the
Fixture Chain (GG) and over the
Canopy Chain Loop (EE). Tighten
the Canopy Lock Ring (FF) onto
the Canopy Chain Loop (EE) until
tight.
Suggested chain length for
Ceiling height :
8’ ceiling : use 8 links of chain and
2 quick links
9’ ceiling : use 18 links of chain
and 2 quick links
10’ ceiling : use 28 links of chain
and 2 quick links
C
D
E
F
Bulb (not
supplied)
Bolt
Socket
Hole
Figure 5
STEP 5 - Making the Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into outlet box.
Note: If the electrical wire is going to be cut shorter than provided
you will need to identify the "L" line wire and the "N" neutral wire
before you cut the excess wire off. One is labeled N and the other
labeled L. To do this separate the "L" line wire and the "N" neutral
wire as far as you need to. Re-label the wire near where you want to
make the cut. Be sure to mark the wire on the side of the fixture and
not on the excess wire being cut and removed.
B.
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire from fixture
identified with the Label “N”
Black wire from
outlet box (or Red)
Black wire from fixture
identified with the label “L”
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture