Installation Sheet

ManualsBrandsQuoizel ManualsChandeliersQuoizel Concert 5 Light 24" Wide Chandelier

1of2

Assembly Instruction Sheet #IS-CRT2824EK

For Style CRT2824EK

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

www quoizel com

2017 QuoizelInc.

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184

or visit us on-line at www.quoizel.com

ReleasedDate:2017-03-28

Pleasegoto forproductcleaningtips.Gotothe selection.

(5)B10CandelabraBaseBulbs60WMaximumor

(5)T8MediumBaseVintage Bulbs are recommended but not supplied.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired: Flathead screwdriver,Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Fixture Loop

Fixture

Body

Hardware Contents

Crossbar

Lock Washer

Hex Nut

Nipple

Canopy

Chain Loop

Canopy Lock

Ring

Ceiling

Canopy

Fixture Chain

Quick Link

Figure 1

STEP 1 Install Fixture Loop-

A. (Refer to Side Arm Orientation)

Unfold side arms to proper locations.

B. Thread the Fixture Loop (A) onto the

top center of the Fixture Body (B)

and hand tighten until snug.

Side Arm

Side Arm Orientation

STEP 2 Install the Crossbar to the junction box-

A. Attach the Crossbar (AA) to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included), tighten until snug

Figure 2

Outlet Box

Outlet Box Screw

(not included)

Green Ground

Screw

STEP 3 Install the Canopy Chain Loop and Nipple-

A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at

least 0.25” from the end. Pass one Lock Washer (BB) over the end

of the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the

Nipple (DD). By using pliers, thread the Hex Nut (CC) against the

Canopy Chain Loop (EE) and hand tighten until snug.

B. Thread another Hex Nut (CC) to the middle of the Nipple (DD).

Place another Lock Washer (BB) over the Nipple (DD) and then

thread the Nipple (DD) into the Crossbar (AA) until the Nipple (DD)

is about 0.375” above the Crossbar (AA).

C. Remove the Canopy Lock Ring (FF) from the Canopy Chain Loop

(EE). Place the Ceiling Canopy (II) over the Canopy Chain Loop

(EE) against the ceiling to determine the correct position of the

Step B

Step A

Nipple (DD). Thread the

Canopy Lock Ring onto the

Canopy Chain Loop (EE).

Adjust the Nipple (DD) to

allow the Ceiling Canopy

(II) to rest against the

ceiling when held in place

by the Canopy Lock Ring

(FF).

D. Remove the Canopy Lock

Ring (FF) and the Ceiling

Canopy (II). Tighten the

Hex Nut (CC) against the

Crossbar (AA) to secure in

place.

Figure 3

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet #IS-CRT2824EK For Style CRT2824EK 6 CORPORATE PARKWAY GOOSE CREEK , SC . 29445 www . quoizel . com Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (5) B10 Candelabra Base Bulbs 60W Maximum or (5) T8 Medium Base Vintage Bulbs are recommended but not supplied.
PAGE 2
STEP 4 - Install the Fixture Chain and Ceiling Canopy STEP 6 - Install Bulbs A. Adjust the Fixture Chain (GG) to your desired length by removing links if needed. B. Pull the supply wires through the Fixture Chain (GG) alternating links. After the wires are through the Fixture Chain (GG), pull the Supply Wires and the Ground Wire through the Canopy Lock Ring (FF) and the Ceiling Canopy (II) in order. C. Attach one end of the Fixture Chain (GG) to the Fixture Loop with one Quick Link (HH).