Installation Sheet

1of2
Pleasegoto forproductcleaningtips.Gotothe selection.
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
(3)A19MediumBaseBulbs100WMaximum,MediumBaseVintageBulbsarerecommended,bulbsnotincluded.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
ToolsRequired:
LightSource:
EstimatedAssembly Time:
Preparation:
Warnings and Cautions
Assembly Instruction Sheet #IS-GFC1617PN
For Style GFC1617PN
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
2018 QuoizelInc.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
ReleasedDate:2018-03-02
Package Contents
A
Crossbar Assembly
x1
D
B
Fixture Body
x1
C
J
Big Flat Washer
x1
F
Shade
x1
Nipple with
Hex Nut
x1
E
Spacer Tube
x1
H
Big Rubber Washer
x1
I
G
Check Ring
x1
Small Rubber Washer
x1
L
Small Flat Washer
x1
M
Hex Nut
x1
Cap
x1
Finial
x1
K
STEP 1 - Installing the Crossbar Assembly
A. Pass the supply wires from outlet box through the Crossbar
Assembly (A). Attach the Crossbar Assembly (A) to the outlet box
with the head of the green ground screw facing you. Secure the
Crossbar Assembly (A) with outlet box screws (not included).
Tighten until snug.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet Box
Figure 1
A
STEP 2 - Test Fitting Ceiling Canopy to Crossbar Assembly
A. Remove mounting balls from the Crossbar Assembly (A). Fit the
ceiling canopy and Fixture Body (B) to the Crossbar Assembly (A)
and secure with mounting balls. Note: The ceiling canopy should be
snug against the ceiling and the mounting balls. If not, adjust the
length of the nipple on the Crossbar Assembly (A) by unscrewing
the preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the ceiling canopy and Fixture Body (B) is secure,
remove the mounting ball and ceiling canopy and Fixture Body (B)
and proceed to Step 3.
Mounting Screw
Hex Nut and
Lock Washer
B
Mounting Ball
A
Figure 2
STEP 3 - Wire Connections
A.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
Figure 3
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture