Installation Sheet

DRIVER
1of2
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Assembly Instruction Sheet #IS-GLW1613W
For Style GLW1613W
Pleasegoto forproductcleaningtips.Gotothe selection.
LED15W
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flathead screwdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Package Contents
A
Crossbar Assembly
x1
Thank you forpurchasing a Quoizelproduct.
Need assistance withparts or assembly?Call Quoizel customerservice at 1-800-645-3184
or visit us on-line at www.quoizel.com
Fixture Body
x1
2018 QuoizelInc.
ReleasedDate:2018-02-02
B
C
Shade
x1
STEP 1 - Installing the Crossbar Assembly
A. Attach the Crossbar Assembly (A) to the Outlet Box with the head
of the Green Ground Screw facing you. Secure the Crossbar
Assembly (A) with Outlet Box Screws (not included). Tighten until
snug.
STEP 2 Test Fitting Ceiling Canopy to Crossbar Assembly-
A.
eiling Canopy to the
ceiling
Remove mounting balls from the Crossbar Assembly (A). Fit the
C (B) Crossbar Assembly (A) and secure with
mounting balls. Note: The C should be snug
against the and the mounting balls. If
eiling Canopy (B)
not, adjust the length
of the nipple on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the Ceiling Canopy (B) is secure, remove the
mounting ball and Ceiling Canopy (B) and proceed to Step 3.
Mounting Screw
Hex Nut and
Lock Washer
Mounting Ball
A
Figure 3
B
Figure 1
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw
A
Figure 2
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
STEP 4 - Install the Fixture
A. Carefully tuck all wires into the outlet box and position the Ceiling
Canopy (B) over the outlet box. Align the holes in the Ceiling Canopy
(B) with the mounting screws, then attach the Ceiling Canopy (B)
using the previously removed mounting balls. Hand tighten until
snug.
Mounting Screw
Mounting Ball
A
B
Figure 4
STEP 5 Install Shade-
A. Align slots on the Shade (C) to studs on the Fixture Body (B) and
twist the Shade (C) until it is hung safety.
Your fixture is now assembled and ready to use. Enjoy!
Stud
Slot
C
Figure 5