Installation Sheet

ManualsBrandsQuoizel ManualsChandeliersQuoizel Hybrid 6 Light 36" Wide Linear Chandelier

1of2

For Style HYR636AN

Pleasegoto forproductcleaningtips.Gotothe selection.

(6)B10CandelabraBasebulbs60WMaximum,bulbnotincluded.

MinimumHangingHeightis20”,MaximumHangingHeightis112”.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.MissingParts?Contactyouroriginalplaceof

purchase.

www.quoizel.com Care+Maintenance

LightSource:

FixtureHangingHeight:

EstimatedAssemblyTime:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Package Contents

Crossbar

Assembly

Fixture

Body

Installation Guide #IS-HYR636AN

2018 QuoizelInc.

ReleasedDate:2018-09-19

visit us on-line at www.quoizel.com

STEP 2 - Installing the Crossbar Assembly

A. Pass the supply wires from outlet box through the Crossbar

Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box

with the head of the Green Ground Screw facing you. Secure the

Crossbar Assembly (A) with Outlet Box Screws (not included).

Tighten until snug.

Outlet Box Screws

(not included)

Outlet Box

Figure 2

Shade

STEP 1 Adjust Fixture Height

Note: Please make sure each cord are in the same length

after adjustment to level the fixture.

A. Loosen the set screw on the coupling underside of the ceiling

canopy. Adjust the cord in or out of the ceiling canopy according

to your hanging height.

B. Tighten the set screw on the coupling once your hanging height

is achieved. Move the safety clip next to the hex nut inside of the

ceiling canopy.

Figure 1

Set Screw

Cord

Coupling

Safety Clip

Hex Nut

Ceiling

Canopy

STEP 3 - Attach the Lanyard

A. The purpose of the lanyard is to provide a means to support the

fixture hands free from the junction box while connecting the

electrical wires.

B. Turn the Button Stop so it may be inserted into a Crossbar slot. Make

sure the Button Stop is completely inside the Crossbar. Slowly

release the fixture to make sure it is supported by the Button Stop.

Proceed to the wiring steps in the next step. Once you are complete

with the wiring, the Lanyard will push into the junction box when the

fixture is placed for final mounting.

Button Stop

Lanyard

Slot

Crossbar

Summary of content (2 pages)

PAGE 1
Installation Guide #IS-HYR636AN For Style HYR636AN Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (6) B10 Candelabra Base bulbs 60W Maximum, bulb not included. Fixture Hanging Height: Minimum Hanging Height is 20”, Maximum Hanging Height is 112”.
PAGE 2
HYR636AN STEP 4 - Wire Connections A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw. B. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box.