Installation Guide

1of2
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
2016 QuoizelInc.
Assembly Instruction Sheet #IS-LND1616MC
For Style LND1616MC
Pleasegoto forproduct cleaningtips. Goto the selection.
(3)A19MediumBase 100Wbulb Maximum,Alternatebulb(3) 23WCFLMaximum.
30-45minutes
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement
parts.
www.quoizel.com Care+ Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers, wirecutters, wirestrippers, electricaltape, safetyglasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
A
Crossbar Assembly
x1
B
Fixture Body
x1
March2016
D
Center
Stem
x1
C
Diffuser
x1
E
Rubber
Washer
x1
G
Hex
Nut
x1
H
Finial
x1
STEP 1 Install Crossbar Assembly-
A. Pass the supply wires through the
Crossbar Assembly (A). Attach the
Crossbar Assembly (A) to the Outlet
Box with the head of the Green
Ground Screw facing you. Secure it
with Outlet Box Screws (not
included). Tighten until snug.
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
A
Figure 1
STEP 2 Fit Ceiling Canopy to Crossbar Assembly-
A.
Ceiling Canopy to the
Ceiling
Canopy ceiling
Remove mounting balls from the Crossbar Assembly (A). Fit the
on the top of Fixture Body (B) Crossbar
Assembly (A) and secure with mounting balls. Note: The
should be snug against the and the mounting balls. If
not, adjust the length of the nipple on the Crossbar Assembly (A) by
unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws in or out of the crossbar until the
correct length is achieved. Once the Ceiling Canopy is secure,
remove the mounting ball and Ceiling Canopy and proceed to Step 3.
Mounting
Screw
Hex Nut and
Lock Washer
Mounting
Ball
A
Figure 2
Ceiling
Canopy
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
STEP 4 Install Fixture Body-
A. Carefully tuck all wires into the outlet box and position the Ceiling
Canopy over the outlet box. Align the holes in the Ceiling Canopy
with the mounting screws, then attach the Ceiling Canopy using the
previously removed mounting balls. Hand tighten until snug.
Mounting
Screw
Mounting
Ball
A
Figure 4
Ceiling
Canopy
F
Flat
Washer
x1