Installation Guide

1of2
Assembly Instruction Sheet #IS-MBK5005VG
For Style MBK5005VG
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc.
Package Contents
Hardware Contents
Fixture Loop
x1
AA
BB
CC
DD
EE
FF
II
Crossbar
x1
Lock Washer
x2
Hex Nut
x2
Long Nipple
x1
Canopy
Chain Loop
x1
Canopy Lock
Ring
x1
Ceiling
Canopy
x1
GG
Fixture Chain
x1
HH
Quick Link
x2
D
STEP 1 Install Crossbar-
A. AA)Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..
Figure 1
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw
AA
of the Nipple (DD) and
thread the Canopy Chain
Loop (EE) onto the Nipple
(DD). By using pliers,
thread the Hex Nut (CC)
against the Canopy Chain
Loop (EE) and hand tighten
until snug.
B. Thread another Hex Nut
(CC) to the middle of the
Nipple (DD). Place another
Lock Washer (BB) over the
Nipple (DD) and then thread
the Nipple (DD) into the
Crossbar (AA) until the
Nipple (DD) is about 0.375”
above the Crossbar (AA).
C. Remove the Canopy Lock
Ring (FF) from the Canopy
Chain Loop (EE). Place the
Ceiling Canopy (II) over the
AA
BB
CC
Step B
Step A
DD
CC
BB
EE
II
FF
Canopy Chain Loop (EE) against the ceiling to determine the
correct position of the Nipple (DD). Thread the Canopy Lock Ring
onto the Canopy Chain Loop (EE). Adjust the Nipple (DD) to allow
the Ceiling Canopy (II) to rest against the ceiling when held in place
by the Canopy Lock Ring (FF).
D. Remove the Canopy Lock Ring (FF) and the Ceiling Canopy (II).
Tighten the Hex Nut (CC) against the Crossbar (AA) to secure in
place.
Figure 2
G
Shade
x5
F
Steel Collar
x5
ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers, wirecutters,wire strippers,electrical tape,safety glasses.
BulbRecommended: (5) MediumBase 100WMaximum,Alternatebulb (5)23W CFL
EstimatedAssemblyTime:
Preparation:
20-30minutes
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besureall partsare
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperatethefixture.Contact customerservice forreplacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering July result.
A
STEP 2 Install Canopy Chain Loop and Nipple-
* Pliers is required for this step.
A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at
least 0.25” from the end. Pass one Lock Washer (BB) over the end
Socket Collar
Tool x 1
Fixture Body
x1
B
Cage
x1
C
E
Socket Collar
x5
STEP 3 - Install Fixture Loop, Fixture Body and
Cage
A. Unfold the arms on Fixture Body (B) to proper
locations.
B. Thread Fixture Loop (A) onto the Fixture Body
(B) and hand tighten until sung.
C. Remove socket collars and steel collars from
socket. Attach the Cage (C) onto the bottom of
the bobeche and secure with Lock Screws (H).
Hand tighten until snug with screwdrivers.
A
B
Figure 3
C
Bobeche
H
Lock
Screw
x5
H
December2014