Instructions / Assembly

1of2
For Style MRN5008AWH, IBMRN5008
Package Contents
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Crossbar
Assembly
x1
Ceiling Canopy
x1
Fixture Chain
x1
Quick Link
x2
Pleasegoto forproductcleaningtips.Gotothe selection.
(8)B10CandelabraBasebulbs60WMaximum,bulbnotincluded.
MinimumHangingHeightis32.5”,MaximumHangingHeightis80.5”.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.MissingParts?Contactyouroriginalplaceof
purchase.
www.quoizel.com Care+Maintenance
LightSource:
FixtureHangingHeight:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
A
B
C
D
STEP 2 - Install the Crossbar Assembly to Outlet Box and Adjust
the length of the Nipple
A. Attach the Crossbar Assembly (A) to the Outlet Box with the head of
the Green Ground Screw facing you. Secure it with Outlet Box
Screws (not included), tighten until snug
B. Adjust the hex nut and lock washer underside of the crossbar to the
middle of the nipple.
C. Remove the canopy lock ring from the canopy chain loop. Place the
Ceiling Canopy (D) over the canopy chain loop against the ceiling to
determine the correct position of the nipple. Thread the canopy lock
ring onto the canopy chain loop. Adjust the nipple to allow the Ceiling
Canopy (D) to rest against the ceiling when held in place by the
canopy lock ring.
D. Remove the canopy lock ring and the Ceiling Canopy (D). Tighten
the lock washer and the hex nut against the crossbar to secure in
place.
.
Outlet Box Screw
(not included)
Hex Nut and
Lock Washer
Outlet Box
Green Ground Screw
Canopy Chain Loop
Canopy Lock Ring
Nipple
STEP 3 - Install the Fixture Chain and Ceiling Canopy
A. Adjust the Fixture Chain (B) to your desired length by removing
links if needed. Put a cloth over the Fixture Chain (B) to protect the
finish.
B. Pull the supply wires through the Fixture Chain (B) alternating links.
After the wires are through the Fixture Chain (B), pull the Supply
Wires and the Ground Wire through the canopy lock ring and the
Ceiling Canopy (D) in order.
C. Attach one end of the Fixture Chain (B) to the fixture loop with one
Quick Link (C). Lift the fixture and Fixture Chain (B) up and attach
the other end of the Fixture Chain (B) onto the canopy chain loop
with another Quick Link (C). The fixture will now hang safely.
D. Feed the Supply Wires and Ground Wire through the canopy chain
loop and nipple into the outlet box. Cut the wires leaving
approximately 8” of wire extending from the Outlet Box.
E. Go to Step 5 for wire connections and follow the directions. Return
to Step F in this step when complete with Step 4.
F. Raise the Ceiling Canopy (D) and canopy lock ring up the Fixture
Chain (B) and over the canopy chain loop. Tighten the canopy lock
ring onto the canopy chain loop until tight.
Installation Guide
2019 QuoizelInc.
visit us on-line at www.quoizel.com
A
D
Figure 2
E
STEP 1 - Install the Fixture Loop
A. Unfold support arms of the Socket assembly (F) to proper locations.
(Refer to Socket Orientation)
b. Thread the Fixture Loop (E) onto the nipple on the top center of the
Fixture Assembly (F). Hand tighten until snug.
F
Fixture Loop
x1
Fixture Assembly
x1
E
F
ReleasedDate:2019-08-19