Installation Sheet

ManualsBrandsQuoizel ManualsChandeliersQuoizel Noble 18 Light 48" Wide Taper Candle Chandelier

1of3

For Style NBE5018RK

Package Contents

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Crossbar

Assembly

Ceiling Canopy

Fixture Chain

Large Quick Link

Pleasegoto forproductcleaningtips.Gotothe selection.

(18)B10CandelabraBasebulbs60WMaximum,bulbnotincluded.

MinimumHangingHeightis61”,MaximumHangingHeightis159.5”.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.MissingParts?Contactyouroriginalplaceof

purchase.

www.quoizel.com Care+Maintenance

LightSource:

FixtureHangingHeight:

EstimatedAssemblyTime:

Preparation:

ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.

Installation Guide #IS-NBE5018RK

2018 QuoizelInc.

ReleasedDate:2019-03-01

visit us on-line at www.quoizel.com

Socket Assembly

Quick Link

x12

Long Arm

Fixture Loop

Short Arm

Fixture Body

Finial

Large Finial

STEP 1 - Install the Fixture Loop Assembly and Arm

a. Insert the Fixture Loop Assembly (F) onto the Coupling of the Socket

Assembly (G).

b. Attach one end of the Long Arm (I) to the fixture loop of the Fixture

Body (H) with one Quick Link (N). attach the other end of the Long

Arm (I) onto the fixture loop of the Center Column (Q) with one Quick

Link (N).

c. Attach one end of the Short Arm (J) to the fixture loop of the Socket

Assembly (G) with one Quick Link (N). attach the other end of the

Short Arm (J) onto the fixture loop of the Center Column (Q) with one

Quick Link (N).

d. Place the cap (P) over the nipple, Secure with the knurled nut (O).

Hand-tighten until snug.

e. Thread (F) onto the Nipple on the top of Center Column

(Q), hand tighten until snug.

Fixture Loop

Mounting Screw

Tuck Washer

Knurled nut

Cap

Center Column

Summary of content (3 pages)

PAGE 1
Installation Guide #IS-NBE5018RK For Style NBE5018RK Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (18) B10 Candelabra Base bulbs 60W Maximum, bulb not included. Fixture Hanging Height: Minimum Hanging Height is 61”, Maximum Hanging Height is 159.5”.
PAGE 2
STEP 2 - Attach Crossbar to Outlet Box and Adjust the length of the Nipple A. Drill a 5/8” diameter clearance hole on the top inside center of the Outlet Box and through the Structural Support Member. B. Place Crossbar Assembly (A) onto the Outlet Box and line up Mounting Holes with a set of holes on Crossbar Assembly (A). C. Thread Outlet Box Screws into the Mounting Holes on the Outlet Box and tighten until snug to secure the Crossbar. D.
PAGE 3
STEP 5 - Making the Wire Connections NBE5018RK A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw. B. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into outlet box. FINISH: RUSTIC BLACK 6” Dia.