Installation Guide

1of3
Assembly Instruction Sheet #IS-NBE5303RK
For Style NBE5303RK
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc.
August2014
Package Contents
Hardware Contents
Ceiling
Canopy
x1
Fixture Chain
x1
HH
Quick Link
x2
B
Side
Arm
x2
A
Fixture
Body
x1
II
JJ
Mounting Screw
x2
KK
Small Lock Washer
x2
MM
Small Hex Nut
x2
STEP 1 Install Crossbar-
A. A)Attach the Crossbar (A to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..
Figure 1
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw
FOR HANGING
Step B
Step A
Figure 2
STEP 2 Install Canopy Chain Loop and Nipple-
* Pliers is required for this step.
A. Thread one Big Hex Nut (CC) to one end of the Nipple (DD) until it is
at least 0.25” from the end. Pass one Big Lock Washer (BB) over the
end of the Nipple (DD) and thread the Canopy Chain Loop (EE) onto
the Nipple (DD). By using pliers, thread the Big Hex Nut (CC) against
the Canopy Chain Loop (EE) and hand tighten until snug.
B. Thread another Big Hex Nut (CC) to the middle of the Nipple (DD).
Place another Big Lock Washer (BB) over the Nipple (DD) and then
thread the Nipple (DD) into the Crossbar (AA) until the Nipple (DD) is
about 0.375” above the Crossbar (AA).
C. Remove the Canopy Lock Ring (FF) from the Canopy Chain Loop
(EE). Place the Ceiling Canopy (II) over the Canopy Chain Loop (EE)
against the ceiling to determine the correct position of the Nipple
(DD). Thread the Canopy Lock Ring onto the Canopy Chain Loop
(EE). Adjust the Nipple (DD) to allow the Ceiling Canopy with Big
Hole (HH) to rest against the ceiling when held in place by the
Canopy Lock Ring (FF).
D. Remove the Canopy Lock Ring (FF) and the Ceiling Canopy (II).
Tighten the Big Hex Nut (CC) against the Crossbar (AA) to secure in
place.
AA
BB
CC
AA
DD
II
EE
Mounting Ball
x2
Crossbar
x1
AA
BB
CC
DD
EE
Lock Washer
x2
Big Hex Nut
x2
Nipple
x1
Canopy
Chain Loop
x1
FF
Canopy Lock
Ring
x1
GG
LL
ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers, wirecutters,wire strippers,electrical tape,safety glasses.
EstimatedAssemblyTime:30-45 minutes
Preparation:
Note:This fixturecan bemounted ashanging orsemi-flush. Referto respectiveinstallation stepsfor installations.
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besureall partsare
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperatethefixture.Contact customerservice forreplacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
BulbRecommended: (3) CandelabraBase 60WMaximum
C
Finial
x1
CC
BB
FF
STEP 3 Install Side Arm and Fixture Body together-
A. Attach have one loop end of Side Arm (B) onto the hook on the top of
Fixture Body (A), have two loops end of Side Arm (B) onto the lower
hook on the Fixture Body(A).
B. Thread Finial (C) onto the nipple on the bottom of Fixture Body (A),
hand tighten until sung.