Installation Guide

Package Contents
Pleasegoto forproductcleaningtips.Gotothe selection.
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Integrated9WLED
www.quoizel.com Care+Maintenance
ToolsRequired:
EstimatedAssemblyTime:
Preparation:
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-PCAW1612W
For Style PCAW1612W
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2016 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Crossbar Assembly
x1
A
C
Fixture
Body
x1
Mounting Screw
x2
B
Figure 3
January2016
GND
2.
4 m
m
13 G
a
Q
U
O
I
Z
E
L
STEP 3 - Attach Fixture Body to Crossbar Assembly
A. Thread Mounting Screws (B) into the side of the flat strap of the
Crossbar Assembly (A). Do not tighten Mounting Screws (B) at this
moment.
B. F
. Fit the slots on the side of the ceiling
canopy to Mounting Screws (B) and then rotate the Fixture Body (C)
it excess cord and electrical wires in the ceiling canopy of the
Fixture Body (C) properly
Outlet Box
A
B
Slot
C
until it is hung safety on the
Mounting Screws (B).
C. Tighten Mounting Screws
(B) until snug with
screwdrivers.
How To Replace Driver
A. Disconnect the fixture from the outlet box.
B. Unplug Driver wires from the Terminal Block by pressing the tabs on
the Terminal Block. Unlock Hex Nuts and Washers on the side of the
Driver and replace the Driver with a new one. Tighten the new Driver
with the previously removed Washers and Hex Nuts.
Hex Nut
Washer
Driver
Bolt
Ceiling
Canopy
C. Block
Block
Connect the Live Wire from Driver to Port “L” on the Terminal ,
which is the corresponding port of the Live Wire from LED Panel.
Connect the Natural Wire from Driver to Port “N” on the Terminal
, which is the corresponding port of the Natural Wire from LED
Panel.
N
L
Live Wire from Driver Live Wire from LED Panel
Natural Wire from Driver Natural Wire from LED Panel
Terminal Block
D. Return to Step 2 to complete the installation of the fixture.
Terminal Block
Wires
STEP 1 Attach Inner Backplate to
Outlet Box
-
A. Attach the Crossbar Assembly (A) to
Outlet Box and secure by threading
Outlet Box Screws (not supplied) into
the Mounting Holes on the Outlet
Box. Tighten until snug.
A
Figure 1
Outlet
Box
Outlet Box
Screw
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 2
STEP 2 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires between Crossbar Assembly (A) and Fixture
Body (C).