Installation Sheet

ManualsBrandsQuoizel ManualsChandeliersQuoizel Borderline 24" Wide Integrated LED Ring Chandelier

Package Contents

Pleasegoto forproductcleaningtips.Gotothe selection.

Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

IntegratedLED12W+IntegratedLED20W

:LutronDVELV-300PorLutronSELV-300P.

www.quoizel.com Care+Maintenance

ToolsRequired:

LightSource:

CompatibleDimmerSwitches

EstimatedAssemblyTime:

Preparation:

20-30minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

Warnings and Cautions

1of3

Assembly Instruction Sheet #IS-PCBN5202C

For Style PCBN5202C

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Crossbar

Assembly

Mounting Screw

Fixture

Body

Crystal

String

Crystal String A

(4) Beads + (1) Drop

x37

Crystal String B

(6)Beads+(1)Drop

x37

Crystal String C

(8)Beads+(1)Drop

x37

Crystal String D

(10) Beads + (1) Drop

(includes two replacements)

x39

STEP 1 Adjust the Fixture Body Height-

A. By using the Allen Wrench (F), unscrew the set screw on the cable

clasp. Push the pin on the bottom of the ceiling canopy and adjust

the cable to your desired hanging height. Release your hand on the

pin and move the cable clasp to the hex nut inside of the ceiling

canopy. Tight the set screw on the cable clasp until snug to engage

the cable.

B. Move the wire clasp to the hex nut inside of the ceiling canopy.

Carefully tuck all slack wires inside of the ceiling canopy.

C. Make sure each ring is horizontal after adjustments.

Figure 1

STEP 2 - Attach Crossbar Assembly to Outlet Box

A. Attach the Crossbar Assembly (A) onto the outlet box and make two

marks on the ceiling from keyholes.

B. Remove the Crossbar Assembly (A) and drill proper holes on the

ceiling from marks. Insert Wall Anchors (C) into the holes properly.

Pass supply wires and ground wire through the center hole of the

Crossbar Assembly (A). Attach the Crossbar Assembly (A) to outlet

box. Thread outlet box screws (not supplied) into mounting holes on

the outlet box. Pass Washers (E) over Self-tapping Screws (D) and

thread Self-tapping Screws (D) into Wall Anchors (C). Hand tighten

until snug.

Ceiling

Canopy

Allen Wrench

Figure 2

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184

or visit us on-line at www.quoizel.com

2017 QuoizelInc.

ReleasedDate:2017-10-25

Set Screw

Cable Clasp

Wire

Clasp

Hex Nut

Top Ring

Bottom Ring

2.4mm

13 Ga13 Ga

Wall Anchor

Self-tapping

Screw

Washer

Outlet Box

Outlet Box Screw

(not supplied)

Supply Wires with

Ground Wire

Summary of content (3 pages)

PAGE 1
Assembly Instruction Sheet #IS-PCBN5202C For Style PCBN5202C Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: Integrated LED 12W + Integrated LED 20W Compatible Dimmer Switches : Lutron DVELV-300P or Lutron SELV-300P.
PAGE 2
STEP 3 - Wire Connections STEP 5 - Attach Crystal Strings A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw. B. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box. A.
PAGE 3
PCBN5202C NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4" FINISH: POLISHED CHROME 2.4mm 13 Ga G ND 9.5” Dia. 8” Dia. 101” OVERALL HEIGHT INCLUDES 96” CORD 10” 10” 14” Dia. 24” Dia. 2017 QuoizelInc. Thank you for purchasing a Quoizel product. Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184 or visit us on-line at www.quoizel.