Installation Guide
Package Contents
Pleasegoto forproductcleaningtips.Gotothe selection.
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Integrated22WLED
www.quoizel.com Care+Maintenance
ToolsRequired:
LightSource:
EstimatedAssemblyTime:
Preparation:
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-PCBZ1616C
_R1
For Style PCBZ1616C
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2016 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Crossbar
x1
A
H
Fixture Body
x1
RevisedDate:2016-04-15
Lock Washer
x1
B
Hex Nut
x1
C
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
Lock Ball
x1
E
I
Panel
x1
Rubber Washer
x3
Lock Screw
x3
F
G
STEP 1 Install Crossbar and Nipple-
A. Secure the Crossbar (A) to the Outlet Box with Outlet Box Screws.
Tighten until snug.
Figure 1
Outlet Box
Outlet Box
Screws
A
B
C
D
Nipple
x1
D
* Pliers is required on this step.
B. Thread the Hex Nut (C) onto one
end of the Nipple (D). Place the
Lock Washer (B) over the Hex
Nut end of the Nipple (D) and
then thread the Nipple (D) into
the center lock hole of the
Crossbar (A). Using pliers,
thread the Hex Nut (C) against
the Crossbar (A) and hand
tighten until snug.
STEP 2 Test Fitting
Fixture Body to Crossbar
Assembly
-
A. Fit the Fixture Body (H)
over the Nipple (D) and
secure with the Lock Ball
(E). The ceiling canopy of
the Fixture Body (H)
should be snug against
the ceiling and the Lock
Ball (E). If not, adjust the
length of the Nipple (D) by
D
H
E
Outlet Box
Figure 2
Ceiling Canopy
(Step 2 Continued)
unscrewing the Hex Nut (C) and the Lock Washer (B) and then
screwing the Nipple (D) in or out of the Crossbar (A) until the correct
length is achieved. Once the ceiling of Fixture Body (H) is secure,
remove the Lock Ball (E) and Fixture Body (H) and proceed to step 3.
STEP 4 Install Fixture Body-
A. Carefully tuck all wires into
the outlet box and position
the ceiling canopy of the
Fixture Body (H) over the
outlet box. Attach the ceiling
canopy of the Fixture Body
(H) over the Nipple (D) and
secure with the Lock Ball (E).
Hand tighten until snug.
Figure 4
STEP 5 - Attach Panel to Fixture Body
A. Attach the Panel (I) onto Fixture Body (H) with crystal beads
upwards. Place Rubber Washers (F) over Lock Screws (G) and
thread Lock Screws (G) into Lock Rods until snug to secure the
Panel (I). Hand tighten until snug.
Your fixture is now assembled and ready to use. Enjoy!
H
I
F
G
Figure 5
Lock
Rod
D
H
E
Outlet Box
Ceiling Canopy
Hex Nut and
Lock Washer