Installation Sheet

ManualsBrandsQuoizel ManualsChandeliersQuoizel Cadence Single Light 23-1/2" Wide 2 Tier LED Ring Chandelier

1of2

For Style PCCA2824EK

Installation Guide IS-PCCA2824EK#

Pleasegoto forproductcleaningtips.Gotothe selection.

Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses,markingpen,1/4”

drillbitanddrill.

LED39W

MinimumHangingHeightis14”,MaximumHangingHeightis100”.

MissingParts?Contactyouroriginalplaceof

purchase.

www.quoizel.com Care+Maintenance

ToolsRequired:

LightSource:

FixtureHangingHeight:

EstimatedAssemblyTime:

Preparation:

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Allen Wrench

Wall Anchor

Screw

Washer

STEP 1 Adjust the Fixture Body Height-

A. By using the Allen Wrench (F), unscrew the set screw on the cord

clasp. Push the pin on the bottom of the ceiling canopy and adjust

the cord to your desired hanging height. Release your hand on the

pin and move the cord clasp to the hex nut inside of the ceiling

canopy. Tight the set screw on the cord clasp until snug to engage

the cord.

(Step 1 Continued)

B. Move the safety clip on the cable until there is enough distance for

cable adjustment. Push pin underside of the ceiling canopy and

adjust the cable in or out of the ceiling canopy to achieve your

desired hanging height. Carefully tuck all slack wires inside of the

ceiling canopy.

C. Make sure each ring is horizontal after adjustments.

STEP 2 Attach Crossbar Assembly to Outlet Box-

A. Attach the Crossbar Assembly (A) onto the outlet box and make two

marks on the ceiling from keyholes.

B. Remove the Crossbar Assembly (A). Using a 1/4” drill bit, drill holes

at each (2) locations marked on the ceiling.

Supply Wires with

Ground Wire

Outlet Box Screw

(not included)

Outlet Box

Figure 2

2018 QuoizelInc.

ReleasedDate:2018-04-13

visit us on-line at www.quoizel.com

Package Contents

Crossbar

Assembly

Mounting Screw

Fixture

Body

2.4mm

13 Ga13 Ga

Figure 1

Ceiling Canopy

Set Screw

Cord Clasp

Safety

Clip

Hex Nut

Top Ring

Bottom Ring

Cord

Cable

Summary of content (2 pages)

PAGE 1
Installation Guide #IS-PCCA2824EK For Style PCCA2824EK Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses, marking pen, 1/4” drill bit and drill. Light Source: LED 39W Fixture Hanging Height: Minimum Hanging Height is 14”, Maximum Hanging Height is 100”.
PAGE 2
(Step 2 Continued) STEP 5 - Attach Fixture Body to Crossbar C. Insert Wall Anchors (C) into drilled holes completely. D. Pass supply wires and ground wire through the center hole of the Crossbar Assembly (A). Attach the Crossbar Assembly (A) to outlet box. Thread outlet box screws (not included) into mounting holes on the outlet box. Pass Washers (E) over Screws (D) and thread Screws (D) into Wall Anchors (C). Hand tighten until snug with screwdrivers. A.