Installation Sheet

1of2
Assembly Instruction Sheet #IS-PCCL2817PK
For Style PCCL2817PK
Package Contents
B
Mounting Screw
x2
Inner Backplate
x1
A
2017 QuoizelInc.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Pleasegoto forproductcleaningtips.Gotothe selection.
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Integrated26WLED
:LutronDVELV-300PorLutronSELV-300P.
www.quoizel.com Care+Maintenance
ToolsRequired:
LightSource:
CompatibleDimmerSwitches
EstimatedAssemblyTime:
Preparation:
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
C
Fixture Body
x1
D
L
Allen Wrench
x1
Outlet Box
Screw
Outlet Box
A
STEP 2: Install Inner Backplate
A. Secure the crossbar (A) to the
outlet box (not included) with outlet
box screws. Tighten until snug.
STEP 3 - Attach Lanyard
A. The purpose of the lanyard is to provide the installer a means to
support the fixture from the junction box while connecting the
electrical wires. This enables the fixture to hang from the junction
box and your hands are free to make the wire connections.
B. Turn the Button Stop so it may be inserted into the Inner Backplate
slot. Make sure the Button Stop is completely inside the Inner
Backplate (A). Slowly release the fixture to make sure it is
supported by the Button Stop. Proceed to the wiring steps in the
next step. Once you are complete with the wiring there is nothing to
do with Lanyard. The Lanyard will push into the junction box when
the fixture is placed for final mounting.
9
11
7
6
15
12
8
13
Crystal A
x16
E
Crystal B
x16
F
Crystal C
x24
G
Crystal D
x28
H
Crystal E
x8
I
Crystal F
x8
J
Crystal G
x8
K
Crystal H
x8
Figure 2
ReleasedDate:2017-11-08
STEP 1 Adjust Fixture Height-
A. Unlock Set Screw on the Rope Clamp by using the Allen Wrench (L).
B. With screwdrivers, remove the Screw to open the Wire Clasp in the
ceiling canopy.
C. Push the Pin on the bottom center of the Ceiling Canopy, adjust the
Steel Cable in or out of the Ceiling Canopy to achieve your desired
hanging height. Once your desired hanging height is achieved,
move the Rope Clamp close to hex nut inside of the Ceiling Canopy,
and then tighten the Set Screw with the Allen Wrench (L).
D. Insert slack wires into Ceiling Canopy. Attach Wire to Wire Clasp in
the Ceiling Canopy and secure with the Screw previously removed.
Tighten until snug with screwdrivers.
L
Cable Clasp
Set Screw
Pin
Cable
Supply Wire
Ceiling
Canopy
Figure 1
Screw
Wire Clasp