Installation Guide

Package Contents
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
BulbRecommended:(9)G4XenonClearBulb,20WMaximum
EstimatedAssemblyTime:
Preparation:
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomer service for replacement
parts.
1of2
Assembly Instruction Sheet #IS-PCEL1616C
For Style PCEL1616C
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc.
July2014
Warnings and Cautions
A
Crossbar
x1
B
Fixture
Body
x1
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Do not touch the bulb with bare hands use a cloth or glove.
C
Crystal
Pendant A
x10
D
Crystal
Pendant B
x4
E
Wall
Anchor
x2
F
Self-tapping
Screw
x2
Flat
Washer
x2
STEP 1 - Attach Inner Backplate to Outlet Box
A. Place the Crossbar (A) onto the Ceiling surface and line up one set
of holes onto mounting holes on Outlet Box. Using a pencil, mark
the locations for Wall Anchors (E).
B. Remove the Crossbar (A) and drill holes from the marks and then
push the Wall Anchors (E) into the holes.
C. Position the Crossbar (A) back onto the Ceiling. Thread the Outlet
Box Screws (not supplied) into the mounting holes on the Outlet
Box to secure it. Hand tighten until snug.
D. Pass the Washers (G) over the Self-tapping screws (F) and then
thread the self-tapping screws (F) into the Wall Anchors (E). Hand
tighten until snug.
Mounting
Ball
x2
G4 Xenon
Clear Bulb
x9
STEP 2 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
Ribbed side wire
from fixture
Black wire from
supply (or Red)
Smooth side wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 2
Mounting
Screw
Ceiling
Canopy
STEP 3 - Attach Ceiling Canopy to Mounting Screw
A. Remove Protective Film from Ceiling Canopy. Place the Ceiling
Canopy on the Fixture Body (B) over the Mounting Screws and
secure with Mounting Balls (H). Hand tighten until snug.
Figure 3
B
STEP 4 -Install Bulb
IMPORTANT:
A. This fixture uses G4 Xenon Clear Bulbs (I). Maximum 20 watts.
B. Insert bulb and seat properly into place.
Do not touch the bulb with bare hands use a cloth or
glove.
Figure 4
Socket
G
H
I
J
Crystal
Pendant C
x1
H
GN
D
Figure 1
Ceiling
Outlet
Box
Mounting
Hole
Outlet Box
Screw
(not include)
F
E
G
A
Protective Film
I