Installation Guide

Package Contents
Pleasegoto forproductcleaningtips.Gotothe selection.
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Integrated16WLED
www.quoizel.com Care+Maintenance
ToolsRequired:
LightSource:
EstimatedAssemblyTime:
Preparation:
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
Warnings and Cautions
1of1
Assembly Instruction Sheet #IS-PCIN1613C
For Style PCIN1613C
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
May2015
Wall Anchor
x2
B
Self-tapping Screw
x2
C
Crossbar
x1
Assembly
A
Mounting Screw
x2
E
F
Fixture Body
x1
STEP 1 Attach Crossbar Assembly to Outlet Box-
A. Attach the Crossbar Assembly (A) onto the Outlet Box and make two
marks on the wall from keyholes on the flat strap of the Crossbar
Assembly (A).
B. Remove the Crossbar Assembly (A) and drill proper holes on the
wall from marks. Insert Wall Anchors (B) into the holes properly.
Attach the Crossbar Assembly (A) to Outlet Box. Thread Outlet Box
Screws (not Supplied) into mounting holes on the Outlet Box. Pass
Washers (D) over Self-tapping Screws (C) and thread Self-tapping
Screws (C) into Wall Anchors (B). Hand tighten until snug.
Outlet Box
B
C
D
Outlet Box Screws
(not Supplied)
Keyhole
A
Figure 1
Flat Washer
x2
D
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 2
STEP 2 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires between Crossbar Assembly (A) and Fixture
Body (G).
STEP 3 - Attach Fixture Body to
Crossbar
A. F
. Line up the
holes on the side of the eiling anopy to
the mounting holes on the
(A). Secure them with
Mounting Screws (E). Tighten until sung.
it excess cord and electrical wires in
the ceiling canopy properly
cc
Crossbar
Assembly
Your fixture is now assembled and ready
to use. Enjoy!
A
E
Ceiling
Canopy
Figure 3
PCIN1613C
FINISH: Polished Chrome
12.5” Sq.
10.5” Sq.
4”
-
+
80*25mm3B2C80*25mm3B2C
-
+
-
+
-
+
80*25mm3B2C80*25mm3B2C
-
+
-
+
NOTE: ALL DIMENSIONS ARE ROUNDED UP TO THE NEAREST 1/4"