Instructions / Assembly

Package Contents
1of2
A
Crossbar
Assembly
x1
D
Shade
x3
C
Socket Collar
x3
E
A
Backplate
C
Socket Collar
Tool x 1
F
B
Alternate
Mounting
screw
x2
STEP 1 Install Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
Figure 1
Supply Wires with
Ground Wire
A
Outlet Box Screws
(not included)
Outlet Box
Mounting Screw
or Alternate Short
Mounting Screw
STEP 2 Test Fitting Backplate
to Crossbar Assembly
-
A.
on Fixture Body (C) to
the
Remove mounting balls from the
Crossbar Assembly (A). Fit the
backplate
Crossbar Assembly (A) and
secure with mounting balls.
Note: The backplate
should be snug against
the wall and the mounting balls.
If
on Fixture
Body (C)
not, adjust the length of the
mounting screws or alternate
short mounting screw on the
Crossbar Assembly (A) by
Mounting Screw
or Alternate Short
Mounting Screw
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
Figure 2
C
(Step 2 Continued)
unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws or alternate short mounting screws
in or out of the crossbar until the correct length is achieved. Once
the backplate on Fixture Body (C) is secure, remove the mounting
ball and Fixture Body (C) and proceed to Step 3.
STEP 4 Install Fixture Body-
A. Carefully tuck all wires into the outlet box and position the
backplate of fixture body (C) over the outlet box. Align the holes in
the backplate with the mounting screws or alternate short mounting
screws. Secure with the previously removed mounting balls and
hand tighten until snug.
Figure 4
Mounting Screw
or Alternate Short
Mounting Screw
Mounting Ball
For Style PCSA8603BN
Installation Guide #IS-PCSA8603BN
Pleasegoto forproductcleaningtips.Gotothe selection.
.
(3)G9ClearXenonBulbs60WMaximum,bulbsnotincluded.
Contactyouroriginalplaceofpurchase.
www.quoizel.com Care+Maintenance
LightSource:
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses
EstimatedAssemblyTime:
Preparation:
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Do not touch the bulb with bare hands use a cloth or glove.
2018 QuoizelInc.
ReleasedDate:2018-12-17
visit us on-line at www.quoizel.com
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 3
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare,orGreen
Ground wire
from outlet box
Ground wire
from Fixture
Fixture Body
x1