Instructions / Assembly

ManualsBrandsQuoizel ManualsCeiling FansShire 23.25 in. Rustic Black Ceiling Fan with Light

Table Of Contents

1 of 6

2020 Quoizel Inc.

visit us on-line at www.quoizel.com

Released Date: 2020-07-27

Light SourceTools Required

BULB BASE TYPE

Candelabra (E12)

4 BULBS REQUIRED

BULB INCLUDED

BULB SHAPE

TYPE B

Fixture Hanging Height

Warnings and Cautions

READ AND SAVE THESE INSTRUCTIONS

1) Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

2) These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

3) WARNING- To Reduce The risk of personal injury, Do not bend the blades when installing the fan, or cleaning the fan. Do not insert foreign

objects in between rotating fan blades.

4) WARNING- To Reduce The Risk Of Fire, Electric Shock, Or Personal Injury, Mount To Outlet Box Marked (Acceptable for Fan Support of

22.7kg(50lbs) or less) And Use Mounting Screws Provided With The Outlet Box.

5) All set screws must be checked, and retightened where necessary, before installation.

6) After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on

one side of the outlet box and the ungrounded conductor on the other side of the outlet box.

7) Disconnect fixture from the power source before replacing bulbs or cleaning. Make sure the bulbs are given sufficient time to cool be before

removing.

8) Suitable for use with solid-state speed controls.

9)Use Only With Light Kits Marked Suitable For Use In Damp Locations

10) This unit weighs 5.7kg.

6” Dia.

23.25” Dia.

21” or 29”

16.5”

LED

Hanger Frame

x 1

Wood Screw

x 2

Wall Anchor

x 1

Flat Washer

x 4

Lock Washer

x 4

Spring Washer

x 4

Package Contents

Screw

x 1

Flat Washer

x 1

Set Screw

x 1

Fastener

x 1

Wire Connector

x 7

Remote Control

Transmitter X 1

Batteries

X 1

Mounting Bracket

X 1

Screw

x 2

PARTS BAG 1

PARTS BAG 2

PARTS BAG 3

Receiver

X 1

12” Rod

X 1

Rod Assembly

x 1

Ceiling Canopy

x 1

Fixture Body

x 1

Fan Blade

X 1

Blade Assembly

Nut X 1

Machine screw

x 2

Spring Washer

x 1

LED Bulb

x 4

Preparation: Identify and inspect all parts before beginning

installation. Check package content list and diagrams below to

ensure all parts are present. If any parts are missing or damaged,

do not attempt to assemble, install, or operate the fixture.

Missing Parts? Contact your original place of purchase.

For Styles SHR3123RK

Installation Guide

Ring

x 1

Allen Wrench

x 1

Summary of content (6 pages)

PAGE 1
Installation Guide For Styles SHR3123RK Tools Required Light Source Fixture Hanging Height 6” Dia. 16.5” 21” or 29” LED 6W BULB BASE TYPE BULB SHAPE Candelabra (E12) TYPE B 4 BULBS REQUIRED BULB INCLUDED 23.25” Dia. Warnings and Cautions READ AND SAVE THESE INSTRUCTIONS 1) Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt. 2) These instructions are provided for your safety.
PAGE 2
Table of Contents Ceiling Bracket STEP 1 Downrod Install Cable STEP 2-4 STEP 5 Canopy& Fan Blade Wiring STEP 6 STEP 8 STEP 1 Use machine screws when securing to existing ceiling fan-rated outlet box. that supports of 50 lbs (22.72 kg) or less. This fan cannot be used for the ceiling which angle is greater than 10 degree. For angled ceilings, point opening toward peak. Use wood screws When securing to support structure with approved electrical outlet box. Drill 9/64” pilot holes.
PAGE 3
STEP 3 Remove the pre-installed setscrew so that the downrod can be inserted. Install Downrod to Fan/Fixture Body STEP 4 Pick the fan up by the down rod only. Place the downrod ball into the slot in the ceiling bracket. 2020 Quoizel Inc. visit us on-line at www.quoizel.com 3 of 6 Tighten the setscrew with screwdriver. Hand tighten.
PAGE 4
STEP 5-SAFETY CABLE A. Pass the cable through one hole on the Fastener first and then turn back to pass the cable through another hole on the Fastener. Make a small loop that is just large enough for the Screw. Once the loop size is determined, thread the Set Screw into the Fastener and hand tighten until snug. B. Place the Spring Washer and the Flat Washer onto the Screw and pass the Screw through the Cable loop. Thread the Screw into the ceiling, structural support close to the Hanger Frame.
PAGE 5
Making the wire connections without the received, the fan and light will be controlled by wall switches only. a. Making the Wire Connections, 1. Remove the current-limiting from the receiver. 2. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw. 3. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together.
PAGE 6
STEP 8 Wall Install Remote Control Transmitter Wall Bracket (If being used) a. Place Remote Control Mounting Bracket on the wall in desired location and use two screws supplied to attach to the wall. b. Insert supplied battery in remote control in a position that is shown inside the remote control cover. Instructions for fan and light remote control. 1. Setting up the remote Remove the rubber stopper from the controller. Then the code must be the same for both controller and remote.