Installation Guide

Pleasegoto forproductcleaningtips.Gotothe selection.
(6)B10CandelabraBase60WMaximum.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-SLT5006IF
For Style SLT5006IF
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
Hardware Contents
AA
BB
CC
DD
EE
FF
Crossbar
x1
Lock Washer
x2
Hex Nut
x2
Nipple
x1
Canopy
Chain Loop
x1
Canopy Lock
Ring
x1
Ceiling Canopy
x1
HH
Quick Link
x2
A
Fixture Loop
x1
3” Drop
x6
April2015
B
Knurled Nut
x1
I
Crystal Drop
x12
H
2.5” Drop
x3
J
3.5” Drop with
10 Beads
x1
L
3” Drop with
11 Beads
x6
II
GG
Fixture Chain
x1
C
Decorative
Arms x 1
D
Center Stem
x1
E
Lock Ball
x3
F
Shade
x1
G
Socket
Assembly
x1
A
B
C
E
F
G
K
D
STEP 1 Install Center Stem,
Decorative Arms, Fixture Loop and
Shade
-
Bolt
Tab
Scroll
Bolt
Bottom View
Figure 1
A. Thread the Center Stem (D) onto the Socket Assembly (G) and hand
tighten until snug.
B. Place the Decorative Arms (C) over the top end of the Center Stem
(D). Insert the ends of Decorative Arms into the Holes on the
Junction Box. Secure it with the Knurled Nut (B). Hand tighten until
snug. Thread the Fixture Loop (A) onto the Center Stem (D) and
hand tighten until snug.
C. Place the Shade (F) over the Decorative Arms (C). Pass the Bolts on
the Scrolls of the Shade (F) through the Tabs on the Decorative Arms
(C) and secure with Lock Balls (E). Hand tighten until snug.
Hole
Junction Box
Figure 2
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw
AA
STEP 2 Install Crossbar-
A. AA)Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..
STEP 3 Install Canopy Chain Loop and Nipple-
* Pliers is required for this step.
A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at
least 0.25” from the end. Pass one Lock Washer (BB) over the end of
the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the
Nipple (DD). By using pliers, thread the Hex Nut (CC) against the
Step B
Step A
CC
BB
EE
II
FF
AA
BB
CC
DD
Figure 3
Canopy Chain Loop (EE) and
hand tighten until snug.
B. Thread another Hex Nut (CC)
to the middle of the Nipple
(DD). Place another Lock
Washer (BB) over the Nipple
(DD) and then thread the
Nipple (DD) into the Crossbar
(AA) until the Nipple (DD) is
about 0.375” above the
Crossbar (AA).
C. Remove the Canopy Lock
Ring (FF) from the Canopy
Chain Loop (EE). Place the
Ceiling Canopy (II) over the
Canopy Chain Loop (EE)
against the ceiling to
determine the correct position
of the Nipple (DD). Thread the
Canopy Lock Ring onto the
Canopy Chain Loop (EE).
Adjust the Nipple (DD) to

Summary of content (2 pages)