Installation Sheet

1of2
For Style TAN5025WT
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Pleasegoto forproductcleaningtips.Gotothe selection.
(9)B10CandelabraBasebulbs60WMaximum,bulbnotincluded.
MinimumHangingHeightis33.5”,MaximumHangingHeightis69.5”.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.MissingParts?Contactyouroriginalplaceof
purchase.
www.quoizel.com Care+Maintenance
LightSource:
FixtureHangingHeight:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Installation Guide #IS-TAN5025WT
2018 QuoizelInc.
visit us on-line at www.quoizel.com
Package Contents
A
Crossbar Assembly
x1
Fixture Body
x1
D
Ceiling Canopy
x1
E
B
6” Rod
x2
C
12” Rod
x2
STEP 1 - Install Ring, Ceiling Canopy, Rods and
Fixture Body together
a. Unfold support arms on fixture assembly to
proper locations.
b. Attach the rings (G/H) to the arm of the Fixture
Body (E). Secure the ring (G/H) with Lock Screw
(I). Tighten until snug.
b. Determine the Rods (B/C) to be assembled to the
Fixture Body (E) according to your hanging
height.
c. Pass the supply wires and ground wire through
the chosen rods (B/C) and the Ceiling Canopy
(D). Thread the Fixture Body (E), the chosen
Rods (B/C) and the Ceiling Canopy (D) together.
Hand tighten until snug.
Suggested rods for Ceiling height :
9’ ceiling : use (1) 12” rods
10’ ceiling : use (2) 6” rods and (1) 12” rods
B
B
D
Supply Wires
and Ground Wire
C
E
C
Figure 1
Glass
x9
F
Large Ring
x1
G
I
Lock
x9
Screws
H
G
STEP 2 - Installing the Crossbar Assembly
A. Pass the supply wires from outlet box through the Crossbar
Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box
with the head of the Green Ground Screw facing you. Secure the
Crossbar Assembly (A) with Outlet Box Screws (not included).
Tighten until snug.
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet Box
A
Figure 2
STEP 3 Test Fitting Ceiling Canopy to Crossbar Assembly-
A.
eiling Canopy to the
ceiling
Remove mounting balls from the Crossbar Assembly (A). Fit the
C (D) Crossbar Assembly (A) and secure with
mounting balls. Note: The should be snug
against the and the mounting balls. If
Ceiling Canopy (D)
not, adjust the length
of the nipple on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the Ceiling Canopy (D) is secure, remove the
mounting ball and Ceiling Canopy (D) and proceed to Step 4.
Mounting Screw
Hex Nut and
Lock Washer
Mounting Ball
A
D
Figure 3
STEP 4 - Attach the Lanyard
A. The purpose of the lanyard is to provide
a means to support the fixture hands
free from the junction box while
connecting the electrical wires.
B.TurntheButtonStopsoitmaybe
inserted into a Crossbar slot. Make sure
the Button Stop is completely inside the
Crossbar. Slowly release the fixture to
make sure it is supported by the Button
Stop. Proceed to the wiring steps in the
next step. Once you are complete with
the wiring, the Lanyard will push into the
junction box when the fixture is placed
for final mounting.
Button Stop
Lanyard
Slot
Figure 4
H
Small Ring
x1
I
I
ReleasedDate:2019-02-21