Installation Guide

ManualsBrandsQuoizel ManualsChandeliersTHL1718MK

Pleasegoto forproductcleaningtips.Gotothe selection.

(4)CandelabraBaseT860WBulbs(supplied),Maximum60W.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

www.quoizel.com Care+Maintenance

BulbRecommended:

EstimatedAssemblyTime:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Note:This CONVERTIBLEfixturecanbemountedaschandelierlightorsemi-flushlight.Refertorespective

installationsteps forinstallations.

Warnings and Cautions

1of3

Assembly Instruction Sheet #IS-THL1718MK

For Style THL1718MK

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

www quoizel com

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

or visit us on-line at www.quoizel.com

2015 QuoizelInc.

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject

glass parts to any shock while in operation or shattering may result.

Package Contents

November2015

Fixture Loop

Candle Cover

Socket Assembly

Bulb

Stem

Side Arm

STEP 1A Attach and Ceiling

Canopy

- Small Loop

A. Thread Nipple (BB) onto the

(GG).

B. Place Ceiling Canopy (HH) and Washer (CC)

over the Nipple (BB). Secure by threading

Hex Nut (DD) onto the Nipple (BB). Tighten

until sung.

Small Loop

Figure 1A

Hardware Contents

Crossbar Assembly

Hex Nut

Nipple

Washer

Quick Link

Fixture Chain

Small

Loop

Ceiling

Canopy

Assembly Instructions for Chandelier Light

(Step 1A - Step 7A)

STEP 2A Install- Fixture Loop, Stem and

Side Arm

A. Attach the Fixture Loop (A), Stem (B) and

Socket Assembly (E) together. Hand-

tighten until snug.

B. Remove lock screws from the Stem (B).

Put the bottom of Side Arm (F) over the

Bolt on the support arms on the Socket

Assembly (J). Line up the Hole on the

Side Arm (F) and the mounting hole on

the Ring of the Stem (B). Secure by

Lock

Screw

Hole

Bolt

Ring

Figure 2A

threading the lock screw

back into the mounting

hole. Hand tighten until

sung.

STEP 3A Install Crossbar Assembly-

A. Pass the supply wires through the

Crossbar Assembly (AA). Attach the

Crossbar Assembly (AA) to the Outlet Box

with the head of the Green Ground Screw

facing you. Secure it with Outlet Box

Screws (not included). Tighten until snug.

Figure 3A

Supply Wires

with Ground Wire

Outlet Box Screws

(not included)

Outlet

Box

STEP 4A Fit Ceiling Canopy to

Crossbar Assembly

Ceiling Canopy to the

Ceiling Canopy

ceiling

Remove mounting balls from the

Crossbar Assembly (AA). Fit the

(HH)

Crossbar Assembly (AA) and

secure with mounting balls. Note:

The (HH) should

be snug against the and

the mounting balls. If Not, adjust

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

Figure 4A

the length of the nipple on the Crossbar Assembly ( ) by

unscrewing the preassembled hex nut and lock washer and then

screwing the mounting screws in or out of the crossbar until the

correct length is achieved. Once the Ceiling Canopy ( ) is

secure, remove the mounting ball and Ceiling Canopy ( ).

Summary of content (3 pages)

PAGE 1
Assembly Instruction Sheet #IS-THL1718MK For Style THL1718MK 6 CORPORATE PARKWAY GOOSE CREEK , SC . 29445 www . quoizel . com Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Bulb Recommended: (4) Candelabra Base T8 60W Bulbs (supplied), Maximum 60W.
PAGE 2
STEP 5A - Install Fixture Chain and Fixture Supply A. Adjust the Fixture Chain (FF) Wires and to your desired length by Ground Wire removing links if needed. * Pliers is required for this step. B. With the Fixture Chain (FF) not attached to GG the Fixture Loop (A) and the Small Loop (GG), pull the supply wires through the Fixture Chain (FF) alternating links. C. Attach one end of the Fixture Chain (FF) to FF the Fixture Loop (A) with one Quick Link (EE).
PAGE 3
(Step 4B Continued) THL1718MK not on the excess wire being cut and removed. FINISH: MARCADO BLACK Use standard wire connectors (not included) to make all wire connections. (Connectors are not included with fixture.) Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into outlet box. White wire from supply CHANDELIER LIGHT 5.5”Dia.