Installation Sheet

1of2
Package Contents
C
Crystal
x10
B
Fixture
Body
x1
Pleasegoto forproductcleaningtips.Gotothe selection.
Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
(10)CandelabraBaseBulbs60WMaximum
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
ToolsRequired:
LightSource:
EstimatedAssemblyTime:
Preparation:
Warnings and Cautions
Assembly Instruction Sheet #IS-TNS5010BN
For Style TNS5010BN
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
A
Fixture Loop
x1
STEP 1 Install Fixture Loop to
Fixture Body
-
A. (Refer to Socket Orientation) Unfold
support arms to proper locations.
B. Thread the Fixture Loop (A) onto the
top center of the Fixture Body (B) and
hand tighten until snug.
Figure 1
A
B
Hardware Contents
AA
Crossbar
Assembly
x1
BB
CC
Ceiling
Canopy
x1
Fixture Chain
x1
Quick Link
x2
DD
2017 QuoizelInc.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
ReleasedDate:2017-08-30
Socket Orientation
Support
Arm
STEP 2 - Install the Crossbar Assembly to Outlet Box and Adjust
the length of the Nipple
A. Attach the Crossbar Assembly (AA) to the Outlet Box with the head
of the Green Ground Screw facing you. Secure it with Outlet Box
Screws (not included), tighten until snug
B. Adjust the hex nut and lock washer underside of the crossbar to the
middle of the nipple.
C. Remove the canopy lock ring from the canopy chain loop. Place the
Ceiling Canopy (DD) over the canopy chain loop against the ceiling
to determine the correct position of the nipple. Thread the canopy
lock ring onto the canopy chain loop. Adjust the nipple to allow the
Ceiling Canopy (DD) to rest against the ceiling when held in place by
the canopy lock ring.
D. Remove the canopy lock ring and the Ceiling Canopy (DD). Tighten
the lock washer and the hex nut against the crossbar to secure in
place.
.
STEP 3 - Install the Fixture Chain and Ceiling Canopy
A. Adjust the Fixture Chain (BB) to your desired length by removing
links if needed. Put a cloth over the Fixture Chain (BB) to protect the
finish.
B. Pull the supply wires through the Fixture Chain (BB) alternating
links. After the wires are through the Fixture Chain (BB), pull the
Supply Wires and the Ground Wire through the canopy lock ring and
the Ceiling Canopy (DD) in order.
C. Attach one end of the Fixture Chain (BB) to the Fixture Loop (A) with
one Quick Link (CC). Lift the fixture and Fixture Chain (BB) up and
attach the other end of the Fixture Chain (BB) onto the canopy chain
loop with another Quick Link (CC). The fixture will now hang safely.
D. Feed the Supply Wires and Ground Wire through the canopy chain
loop and nipple into the outlet box. Cut the wires leaving
approximately 8” of wire extending from the Outlet Box.
Outlet Box Screw
(not included)
Hex Nut and
Lock Washer
Outlet Box
Green Ground Screw
AA
Canopy Chain Loop
Canopy Lock Ring
Figure 2
Nipple
DD