Installation Guide

Pleasegoto forproductcleaningtips.Gotothe selection.
(5)MediumBaseDecorativeFilament60Wbulbs(provided),Maximum100W,Alternatebulb(5)23WCFLMaximum.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-TRG5105
For Styles TRG5105OZ and TRG5105BN
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2016 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering July result.
Package Contents
A
Hardware Contents
Fixture
Loop
x1
Shade
x5
AA
BB
CC
DD
EE
FF
II
Crossbar
x1
Lock Washer
x2
Hex Nut
x2
Nipple
x1
Canopy
Chain Loop
x1
Canopy Lock
Ring
x1
Ceiling Canopy
x1
GG
Fixture Chain
x1
HH
Quick Link
x2
D
AA
BB
CC
Step B
Step A
DD
CC
BB
EE
II
FF
Figure 2
B
Spacer
x1
C
Socket
Assembly
x1
Bulb
x5
F
Socket
Collar
x5
E
STEP 3 Attach Fixture Loop,
Center Stem, Socket Assembly
and Side Arm together
-
A. Unfold support arms on Socket
Assembly to proper locations.
B. Place Spacer (B) over the
Nipple on the top of Socket
Assembly (C), secure by
threading the Fixture Loop (A)
onto the Nipple, hand tighten
until sung.
A
B
C
Figure 3
ReleaseDate:2016-04-01
STEP 1 Install Crossbar-
A. AA)Attach the Crossbar ( to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included) Tighten until snug..
Figure 1
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw
AA
STEP 2 Install Canopy Chain Loop and Nipple-
* Pliers is required for this step.
A. Thread one Hex Nut (CC) to one end of the Nipple (DD) until it is at
least 0.25” from the end. Pass one Lock Washer (BB) over the end of
the Nipple (DD) and thread the Canopy Chain Loop (EE) onto the
Nipple (DD). By using pliers, thread the Hex Nut (CC) against the
Canopy Chain Loop (EE) and hand tighten until snug.
B. Thread another Hex Nut (CC) to the middle of the Nipple (DD). Place
another Lock Washer (BB) over the Nipple (DD) and then thread the
Nipple (DD) into the Crossbar (AA) until the Nipple (DD) is about
0.375” above the Crossbar (AA).
C. Remove the Canopy Lock Ring (FF) from the Canopy Chain Loop
(EE). Place the Ceiling Canopy (II) over the Canopy Chain Loop (EE)
against the ceiling to determine the correct position of the Nipple
(DD). Thread the
Canopy Lock Ring onto
the Canopy Chain Loop
(EE). Adjust the Nipple
(DD) to allow the
Ceiling Canopy (II) to
rest against the ceiling
when held in place by
the Canopy Lock Ring
(FF).
D. Remove the Canopy
Lock Ring (FF) and the
Ceiling Canopy (II).
Tighten the Hex Nut
(CC) against the
Crossbar (AA) to
secure in place.