Instructions / Assembly

2. Avoid atomizing material by using a spray tip size of .035
to .051. Spray head should be held 8 to 12 inches from the
surface so that the flood coat runs down the wall approxi-
mately 6-12 inches below the point of application.
3. Avoid application in windy weather.
4. Trigger gun off at the end of each pass to avoid using exces-
sive materials. Stop all applications only at corners, joints,
seams, or edges.
5. Multiple coats may be applied, whiting or yellowing
will not occur.
TECHNICAL DATA
Material Type Silane/Siloxane
Active Content 100%
Volume Solids 40 or 80% (Depends on Dilution)
Color of Material Milky White
Odor Slight Ammonia Odor
V.O.C. <15 g/L V.O.C. Compliant
Flash Point Non-Flammable
pH Value Approximately 12.5
Viscosity 9.6 Seconds No. 4 Ford Cup
Weight Approximately 8.7 lbs./gal.
Surface Dry/Recoat Approx 1 Hour
Full Chemical Cure 5 to 7 days
TEST DATA
Wind Driven Rain ASTM E-514-86. 98.7% Leak Red
Water Pen Fed Spec SS-W-110C 75% Min Req
96.8% Leak Red Chloride Ion Intr
Salt Pounding NCHRP No. 244 Series IV - 95% Red.
244 Series II - 83% Red.
Water Abs CMU ASTM C140-75
98.6% Effective
Water Vapor Trans ASTM D-1653-71
100% Vapor Perm
Water Repellency ASTM C67-87
98.6% Effective
Weathering ASTM G-53 3500 Hours - No Change
Surface Burning ASTM E84 Flame Spread 0, Smoke developed 0
LIMITED WARRANTY PROCEDURES/INFORMATION
The information contained herein is offered in good faith and is
believed to be accurate. To be eligible for a Rainguard Warranty
the following must occur:
1. A site visit must be conducted by an employee or agent of
Rainguard and a Field Inspection Report completed.
2. A Warranty Application must be fully completed by the
applicator.
3. Field Inspection Report, Warranty Application, and a copy
of the distributor’s invoice must be submitted to and ap-
proved by Rainguard.
4. For graffiti warranty please refer to Rainguard VandlSystem
products.
This material is only warranted when applied in accordance with
the manufacturer’s guidelines and warranty procedures. With-
out adherence to these specific guidelines, no expressed or im-
plied warranty of this product is given. Please contact Rainguard
for additional information.
PRECAUTIONS & LIMITATIONS
All surfaces to be coated should be clean of any dirt and grime,
efflorescence, lime run, form oils and release agents, grease, mud,
excess mortar, and mold and mildew, etc. All cracks should be
pointed or caulked. All voids, bee holes, masonry surface defects
and openings such as conduits, pipes, drains, door frames, vents,
air conditioner openings, electrical openings, control joints, or
any dissimilar materials should be repaired using urethane or oth-
er approved patching.
Do not apply to surfaces if moisture content is greater than 15%
as measured with an electronic moisture meter. Do not apply
materials in climates where freezing temperatures have existed
prior to application. Allow adequate time for surfaces to thaw.
Establish that air, surface, and material temperatures are above
40°F (4.4°C) and at least 5°F above the dew point prior to
painting. Do not apply at temperatures below 40°F or when
temperatures are expected to drop below 40°F within 48 hours
of application. Do not apply if rain, snow, or lower temperatures
are expected within 48 hours. Do not apply if relative humidity is
greater than 90%.
Use material in a well-ventilated area. Protect the work of other
trades. Protect shrubbery and other plants with drop cloths. Pro-
tect automobiles and all other areas not to be coated from over-
spray. Remove overspray from any windows, automobiles, metal,
etc. as soon as possible should it occur. To prevent permanent
staining, clean spills or leaks in a timely manner.
Store materials in a well-protected area between 45° and 90°F.
Avoid freezing temperatures, direct sunlight, and moisture. Keep
away from heat sources.
Dilution - Concentrate ONLY
If product is Ready To Use - DO NOT DILUTE
10 Year Warranty - 9 parts water, 9:1 Mix ratio
20 Year Warranty - 4 parts water, 4:1 Mix ratio
10 Year Warranty - 1 ECO-Pod™ per 1 gallon of water
20 Year Warranty - 2 ECO-Pod™ per 1 gallon of water
10 Year Warranty - 1 32 oz. Quart per 4.75 gallons of water
20 Year Warranty - 2 32 oz. Quarts per 4.75 gallons of water
TEST PANEL
Always apply material to a mock wall or test panel. Test
wall or actual surface area to determine acceptable color,
surface porosity, application rates and methods before start-
ing general application.
FOLLOW THESE SIMPLE STEPS
1. MICRO-SEAL should be applied using low-pressure airless
spray equipment.