Use and Care Manual

ManualsBrandsRAIN GUARD ManualsBuilding materialsVandlSystem 1-gal. VandlGuard Finish Coat Non-Sacrificial Anti-Graffiti Coating

RECOMMENDED USES:

 Aggregate panels

 Concrete, brick, or stucco

 EFIS and cement plaster

 Metal

 Over water-based and solvent-based coatings

 Plastic

 Previously or newly-painted surfaces.

 Stone

 Wood

COVERAGE RATES (THEORETICAL):

Porous Surfaces Square Feet

One Coat Per Gallon

Precision Block 225

Split Face Block 225

Ground Face Block 225

Scored/Fluted Block 200

Sand Blasted Block 200

Slump/Adobe Block 225

Heavy Textured Stucco 250

Brick 250

Unpainted Wood 275

Porous Tile 250

Dense Surfaces

One Coat

Fine/Medium Textured Stucco 250

Pre-Cast/Tilt-up Concrete 275

Cast Concrete 275

Sand Blasted Concrete 250

Exposed Aggregate 275

EFIS 250

Metal 300

Painted Surfaces 300

See Base Coat

Division 9

Warranty Period:

CSI Reference:

Part Numbers:

1 Gallon Reg Finish VG-7009

5 Gallon Reg Finish VG-7008

VANDLGUARD

Finish Coat™

NON-SACRIFICIAL ANTI-GRAFFITI COATING

PRODUCT DESCRIPTION

Rainguard VANDLGUARD Finish Coat Non-Sacrificial Anti-Graffiti Coating

is a finishing coat used in connection with VANDLGUARD FIVE and

VANDLGUARD TEN graffiti protection systems. This product is a water-

based emulsion that dries to a clear and non-yellowing matte or zero

gloss finish. This product is not to be used as a stand alone product.

VANDLGUARD Finish Coat

 Less than 20 g/L VOC

 Non-flammable

 To be used as a final coat over VANDLGUARD FIVE and VANDL-

GUARD TEN graffiti protection systems.

 Simply apply the required base coat and then apply this finish system

for a tough and durable coating

 Meets Master Painters institute (MPI) #105 - Graffiti-Protection,

Top Coat

Rainguard VANDLGUARD Finish Coat may be used to protect interior or

exterior painted and unpainted surfaces, such as masonry, stucco, and

concrete. For application to new masonry, stucco, or concrete surfaces,

a first coat of Rainguard water-repellent protection is required.

A COMPLETE SYSTEM

Bare Surfaces: First apply one coat of

MICRO-SEAL Water-Repellent

by Rainguard (required for

applications that need warranties

and substrate is unpainted or sealed)

For applications that do not require material and labor warranties,

and only need material warranties please refer to VANDLGUARD™

Non-Sacrificial Graffiti Coating.

 UV protectant

5 Gallon Zero Gloss VG-8007SP

1 Gallon Zero Gloss VG-8002SP

Summary of content (2 pages)

PAGE 1
VANDLGUARD Finish Coat™ NON-SACRIFICIAL ANTI-GRAFFITI COATING PRODUCT DESCRIPTION Rainguard VANDLGUARD Finish Coat Non-Sacrificial Anti-Graffiti Coating is a finishing coat used in connection with VANDLGUARD FIVE and VANDLGUARD TEN graffiti protection systems. This product is a waterbased emulsion that dries to a clear and non-yellowing matte or zero gloss finish. This product is not to be used as a stand alone product.
PAGE 2
HOW TO USE: All surfaces to be coated should be structurally sound, clean, and dry. VANDLGUARD Finish Coat™ should be used as a top coat to VANDLGUARD FIVE or VANDLGUARD TEN. By using airless spray equipment, apply VANDLGUARD Finish Coat at recommended coverage rates. Apply in a fine mist, cross-hatched pattern to build up the wet coating. As soon as the entire surface has been coated, immediately repeat process with a second pass.