2013 RAM TRUCK 1500/2500/3500 FCA US LLC 13D241-126-AJ Tenth Edition Rev 1 Printed in U.S.A.
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name FCA US LLC shall be deemed to be deleted and the name FCA Canada Inc. used in substitution therefore. DRIVING AND ALCOHOL Drunken driving is one of the most frequent causes of accidents. Your driving ability can be seriously impaired with blood alcohol levels far below the legal minimum. If you are drinking, don’t drive. Ride with a designated nondrinking driver, call a cab, a friend, or use public transportation.
SECTION TABLE OF CONTENTS PAGE 1 1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 2 3 UNDERSTANDING THE FEATURES OF YOUR VEHICLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 3 4 UNDERSTANDING YOUR INSTRUMENT PANEL . . . . . . . . . . . . . . . . . . . . . . . . . .
INTRODUCTION CONTENTS 䡵 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . .4 䡵 VEHICLE IDENTIFICATION NUMBER . . . . . . . .7 䡵 HOW TO USE THIS MANUAL . . . . . . . . . . . . . .4 䡵 VEHICLE MODIFICATIONS/ALTERATIONS . . . .8 䡵 WARNINGS AND CAUTIONS . . . . . . . . . . . . . .6 䡵 VAN CONVERSIONS/CAMPERS . . . . . . . . . . . .
4 INTRODUCTION When it comes to service, remember that your authorized dealer knows your vehicle best, has factory-trained techCongratulations on selecting your new FCA US LLC nicians and genuine parts, and cares about your satisfacvehicle. Be assured that it represents precision workmantion. ship, distinctive styling, and high quality - all essentials that are traditional to our vehicles.
INTRODUCTION 5 1
6 INTRODUCTION WARNINGS AND CAUTIONS Operating instructions for the special equipment installed by the conversion/camper manufacturer should also be supplied with your vehicle. If these instructions are missing, please contact your authorized dealer for assistance in obtaining replacement documents from the applicable manufacturer. This Owners Manual contains WARNINGS against operating procedures that could result in a collision or bodily injury.
INTRODUCTION 7 VEHICLE IDENTIFICATION NUMBER 1 The Vehicle Identification Number (VIN) is found on the left front corner of the instrument panel, visible through the windshield. This number also appears on the vehicle frame and underbody as well as the Automobile Information Disclosure Label affixed to a window on your vehicle, the vehicle registration and title. Vehicle Identification Number NOTE: It is illegal to remove or alter the VIN.
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a collision resulting in serious injury or death.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2 CONTENTS 䡵 A WORD ABOUT YOUR KEYS . . . . . . . . . . . . .12 䡵 VEHICLE SECURITY ALARM — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . ▫ Ignition System . . . . . . . . . . . . . . . . . . . . . . . .12 ▫ Rearming Of The System . . . . . . . . . . . ▫ Key Fob . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14 ▫ To Arm The System . . . . . . . . . . . . . . . ▫ Removing Key Fob From Ignition . . . . . . . . . .16 ▫ To Disarm The System . . . . . .
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE ▫ To Lock The Doors . . . . . . . . . . . . . . . . . . . . .26 ▫ Child-Protection Door Lock . . . . . . . . . . . . . . .37 ▫ Sound Horn With Remote Key Lock . . . . . . . . .27 䡵 KEYLESS ENTER-N-GO™ . . . . . . . . . . . . . . . . .39 ▫ Using The Panic Alarm . . . . . . . . . . . . . . . . . .27 䡵 WINDOWS . . . . . . . . . . . . . . . . . . . . . . . . . . .43 ▫ RKE Air Suspension (Remote Lowering Of The Vehicle) — If Equipped . . . . . . . . . . . . .
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 ▫ Energy Management Feature . . . . . . . . . . . . . .61 ▫ Event Data Recorder (EDR) . . . . . . . . . . . . . . .82 ▫ Seat Belt Pretensioners . . . . . . . . . . . . . . . . . .62 ▫ Child Restraints . . . . . . . . . . . . . . . . . . . . . . .83 ▫ Enhanced Seat Belt Use Reminder System 䡵 ENGINE BREAK-IN RECOMMENDATIONS (BeltAlert®) . . . . . . . . . . . . . . . . . . . . . . . . . .62 䡵 SAFETY TIPS . . . . . . . . . . . . . . . . . . . . . .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition System Fob with Remote Keyless Entry (RKE) — If Equipped Your vehicle may be equipped with either an Ignition Node Module (IGNM) which operates similar to a standard ignition switch, or a Keyless Ignition Node (KIN) which allows the driver to operate the ignition switch with the push of a button, as long as the Remote Keyless Entry (RKE) transmitter is in the passenger compartment.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 Keyless Ignition Node (KIN) — If Equipped This feature allows the driver to operate the ignition switch with the push of a button, as long as the Remote Keyless Entry (RKE) transmitter is in the passenger compartment. The Keyless Ignition Node (KIN) has four operating positions, three of which are labeled and will illuminate when in position. The three positions are OFF, ACC, and ON/RUN. The fourth position is START, during start RUN will illuminate.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Key Fob The Key Fob operates the ignition switch. Insert the square end of the key fob into the ignition switch located on the instrument panel and rotate to the desired position. It also contains the Remote Keyless Entry (RKE) transmitter and an emergency key, which stores in the rear of the Key Fob. The emergency key allows for entry into the vehicle should the battery in the vehicle or the RKE transmitter go dead.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 2 Emergency Key Removal (WIN) Emergency Key Removal Keyless Enter-N-Go™ Fob (KIN) NOTE: You can insert the double-sided emergency key into the lock cylinder with either side up.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Removing Key Fob From Ignition Place the shift lever in PARK (if equipped with an automatic transmission). Turn the Key Fob to the OFF position and then remove the Key Fob. NOTE: • For vehicles not equipped with the Electronic Vehicle Information Center (EVIC), the power window switches, radio, power sunroof (if equipped), and power outlets will remain active for 45 seconds after the ignition switch is turned to the OFF position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 WARNING! WARNING! (Continued) • Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, and push ignition button to place ignition in OFF position. When leaving the vehicle, always lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. • Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE operation. Therefore, only Key Fobs that are programmed to the vehicle can be used to start and operate • ⬙Keyed⬙ Ignition systems will chime in OFF or ACC the vehicle. The system will not allow the engine to crank when the driver door is open. if an invalid Key Fob is used to start and operate the • “Keyless⬙ Ignition systems will chime in ACC or RUN vehicle. The system will shut the engine off in two seconds if an invalid Key Fob is used to start the engine.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 If the Vehicle Security Light turns on during normal vehicle operation (vehicle running for longer than 10 seconds), it indicates that there is a fault in the electronics. Should this occur, have the vehicle serviced as soon as possible by an authorized dealer. CAUTION! The Sentry Key® Immobilizer system is not compatible with some after-market remote starting systems.
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Duplication of Key Fobs may be performed at an autho- • This device must accept any interference that may be received, including interference that may cause underized dealer, this procedure consists of programming a sired operation. blank Key Fob to the vehicle electronics. A blank Key Fob is one that has never been programmed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 Rearming Of The System To Disarm The System The Vehicle Security Alarm will rearm itself after the 15 additional minutes of headlights and Vehicle Security Light flashing, if the system has not been disabled. If the condition which initiated the alarm is still present, the system will ignore that condition and monitor the remaining doors and ignition. Use the RKE transmitter to unlock the door.
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE you are in the vehicle or not. If you remain in the vehicle and open a door, the alarm will sound. If this occurs, disarm the Vehicle Security Alarm. The lights will fade to off after approximately 30 seconds, or they will immediately fade to off once the ignition switch is turned to ON/RUN from the OFF position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED The RKE system allows you to lock or unlock all doors, tailgate, and the RamBox® (if equipped) as well as activate the Panic Alarm from distances up to approximately 33 ft (10 m) using a hand-held radio transmitter with integrated key. The transmitter does not need to be pointed at the vehicle to activate the system.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Unlock The Doors Press and release the UNLOCK button on the RKE transmitter once to unlock the driver’s door (If EVIC is setup for driver door first, otherwise this will unlock all doors), or press the unlock button twice within five seconds to unlock all doors, the tailgate and the RamBox® (if equipped). The turn signal lights will flash to acknowledge the unlock signal. The illuminated entry system will also turn on.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 3. Test the feature while outside of the vehicle by pressing the LOCK/UNLOCK buttons on the RKE transThis feature lets you program the system to unlock either mitter with the ignition switch in the OFF position and the driver’s door or all doors on the first press of the the key removed. UNLOCK button on the RKE transmitter. To change the current setting, proceed as follows: 4. Repeat these steps if you want to return this feature to its previous setting.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Test the feature while outside of the vehicle by pressing the LOCK/UNLOCK buttons on the RKE transThis feature will cause the turn signal lights to flash when mitter with the ignition switch in the OFF position and the doors are locked or unlocked with the RKE transmitthe key removed. ter. This feature can be turned on or turned off. To change the current setting, proceed as follows: 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 3. Test the feature while outside of the vehicle by pressing the LOCK button on the RKE transmitter with the igniThis feature will cause the horn to chirp when the doors tion switch in the OFF position and the key removed. are locked with the RKE transmitter. This feature can be turned on or turned off. To change the current setting, 4. Repeat these steps if you want to return this feature to proceed as follows: its previous setting.
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Panic Alarm will stay on for three minutes unless RKE Air Suspension (Remote Lowering Of The you turn it off by either pressing the PANIC button a Vehicle) — If Equipped second time or drive the vehicle at a speed of 5 mph (8 km/h) or greater. For easy entry and loading, your vehicle can be lowered by pressing the Key Fob air suspenNOTE: sion lowering button two times.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 Cancelling Remote Lowering Vehicle lowering can be cancelled at anytime. When vehicle lowering is cancelled, the vehicle will raise up to the next defined level and lock out the remote lowering feature until the ignition has been cycled ON/OFF. Transmitter Battery Replacement The recommended replacement battery is one CR2032 battery. NOTE: To cancel vehicle lowering, press the Key Fob air suspen- • Perchlorate Material — special handling may apply. See www.
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. To assemble the RKE transmitter case, snap the two If your RKE transmitter fails to operate from a normal distance, check for these two conditions: halves together. General Information 1. A weak battery in the transmitter. The expected life of the battery is a minimum of three years. This device complies with Part 15 of the FCC rules and RSS 210 of Industry Canada. Operation is subject to the 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 NOTE: • Battery at an acceptable charge level • The vehicle must be equipped with an automatic • transmission to be equipped with Remote Start. • • Obstructions between the vehicle and the RKE trans• mitter may reduce this range.
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Start Abort Message On Electronic Vehicle Information Center (EVIC) — If Equipped To Enter Remote Start Mode The following messages will display in the EVIC if the vehicle fails to remote start or exits remote start prematurely: • Remote Start Aborted — Hood Ajar Press and release the REMOTE START button on the RKE transmitter twice within five seconds.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 • For security, power window and power sunroof op- To Exit Remote Start Mode And Drive The Vehicle eration (if equipped) are disabled when the vehicle is Before the end of the 15-minute cycle, press and release in the Remote Start mode. the UNLOCK button on the RKE transmitter to unlock • The engine can be started two consecutive times (two the doors and disarm the Vehicle Security Alarm System 15-minute cycles) with the RKE transmitter.
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Remote Start Comfort Systems — If Equipped DOOR LOCKS When remote start is activated, the heated steering Manual Door Locks wheel, and driver heated seat features will automatically Front and rear doors may be locked by moving the lock turn on in cold weather. In warm weather, the driver knob down or unlocked by moving the lock knob up. vented seat feature will automatically turn on when the remote start is activated.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Front doors may be opened with the inside door handle without lifting the lock knob. Doors locked before closing will remain locked when closed. The emergency key will unlock the driver door lock on your vehicle. WARNING! • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death.
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE accidentally locking your Key Fob in the vehicle. Removing the Key Fob or closing the door will allow the locks to A power door LOCK switch is on each front door trim operate. A chime will sound if the Key Fob is in the panel. Use this switch to lock or unlock the doors. ignition switch and a door is open, as a reminder to remove the Key Fob.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Auto Unlock Doors Programming — If Equipped The Auto Unlock Doors feature can be enabled or disabled as follows: 2 For vehicles equipped with the EVIC, refer to “Electronic Vehicle Information Center (EVIC)/Personal Settings (System Setup)” in “Understanding Your Instrument Panel” for further information. NOTE: Use the Auto Unlock Doors feature in accordance with local laws.
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the Child-Protection locks are engaged. NOTE: • After setting the Child-Protection Door Lock system, always test the door from the inside to make certain it is in the desired position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 • If the vehicle is unlocked by the Passive Entry Door Handle, and no door goes ajar within 60 seconds, the The Passive Entry system is an enhancement to the vehicle will re-lock and if equipped will arm the theft vehicle’s Remote Keyless Entry (RKE) system and a alarm. feature of Keyless Enter-N-Go™. For further information, refer to “Keyless Enter-N-Go™” in “STARTING AND • The vehicles theft alarm can be armed/disarmed by OPERATING”.
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Unlock From The Driver’s Side: With a valid Passive Entry RKE transmitter within 5 ft (1.5 m) of the driver door handle, grab the front driver door handle to unlock the driver’s door automatically. The interior door panel lock knob will raise when the door is unlocked. NOTE: If “Unlock All Doors 1st Press” is programmed all doors will unlock when you grab hold of the front driver’s door handle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 Preventing Inadvertent Locking Of Passive Entry RKE To Lock The Vehicle’s Doors Transmitter In Vehicle With one of the vehicle’s Passive Entry RKE transmitters To minimize the possibility of unintentionally locking a within 5 ft (1.5 m) of the driver or passenger front door Passive Entry RKE transmitter inside your vehicle, the handles, press the door handle LOCK button to lock all Passive Entry system is equipped with an automatic door doors.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Do NOT grab the door handle, when pressing the door NOTE: handle lock button. This could unlock the door(s). • After pressing the door handle LOCK button, you must wait two seconds before you can lock or unlock the doors, using either Passive Entry door handle. This is done to allow you to check if the vehicle is locked by pulling the door handle, without the vehicle reacting and unlocking.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WINDOWS Power Windows – If Equipped The control on the left front door panel has UP-DOWN switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of the Crew Cab models.
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 To stop the window from going all the way up during the Reset Auto-Up Auto Up operation, push down on the switch briefly. Should the Auto Up feature stop working, the window To close the window part way, lift the window switch to the probably needs to be reset. To reset Auto Up: first detent and release when you want the window to stop. 1.
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE return the switch to the released or up position. Wind Buffeting Wind buffeting can be described as the perception of pressure on the ears or a helicopter-type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down, or the sunroof (if equipped) in certain open or partially open positions. This is a normal occurrence and can be minimized.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 OCCUPANT RESTRAINTS • Knee bolsters/blockers for front seat occupants Some of the most important safety features in your • All seat belt systems (except driver’s, front center and vehicle are the restraint systems: second row center position) include Automatic Locking Retractors (ALRs), which lock the seat belt web• Three-point lap and shoulder belts for the driver and bing into position by extending the belt all the way out all passengers and then adjusting
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: The Advanced Front Air Bags have a multistage inflator design. This allows the air bag to have different rates of inflation based on several factors, including the severity and type of collision. secured in the rear seat in child restraints or beltpositioning booster seats. Older children who do not use child restraints or belt-positioning booster seats should ride properly buckled up in the rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 4. Do not lean against the door or window. If your vehicle has side air bags, and deployment occurs, the side air bags will inflate forcefully into the space between you and the door. 5. If the air bag system in this vehicle needs to be modified to accommodate a disabled person, contact the Customer Center. Phone numbers are provided under ⴖIf You Need Assistanceⴖ. WARNING! • Relying on the air bags alone could lead to more severe injuries in a collision.
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) Lap/Shoulder Belts All seating positions except the Quad Cab®, Mega Cab® and Crew Cab front center seating position have combination lap/shoulder belts. The belt webbing retractor is designed to lock during very sudden stops or collisions. This feature allows the shoulder part of the belt to move Buckle up even though you are an excellent driver, even freely with you under normal conditions. However, in a on short trips.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 WARNING! (Continued) • Be sure everyone in your vehicle is in a seat using a seat belt properly. • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is above the back of the front 3. When the belt is long enough to fit, insert the latch seat, next to your arm in the rear seat. Grasp the latch plate into the buckle until you hear a “click.” plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 WARNING! WARNING! (Continued) • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you properly. In a sudden stop you could move too far forward, increasing the possibility of injury. Wear your seat belt snugly. • A belt that is worn under your arm is dangerous.
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen. Always wear the lap belt as low as possible and keep it snug. • A twisted belt may not protect you properly. In a collision, it could even cut into you. Be sure the belt is straight.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 6. To release the belt, push the red button on the buckle. Regular Cab Front Center Three Point Belt The belt will automatically retract to its stowed posi1. The front center seat belt on the Regular Cab may be tion. If necessary, slide the latch plate down the disconnected to open up utilization of the storage webbing to allow the belt to retract fully. areas behind the front seats.
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Detaching Buckle With Seat Belt Tongue 2. To reattach the seat belt to the front center seat, pull the black buckle latch plate forward from the cab back panel and insert it into the black keyed buckle until there is an audible “click”. For proper seat belt usage, refer “Lap/Shoulder Belt Operating Instructions”.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 WARNING! (Continued) proper restraint and will increase the risk of injury in a collision. • When reattaching the black latch and black buckle, ensure the seat belt webbing is not twisted. If the webbing is twisted, follow the preceding procedure to detach the black latch and black buckle, untwist the webbing, and reattach the black latch and black buckle.
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Untwisting Procedure Adjustable Upper Shoulder Belt Anchorage Use the following procedure to untwist a twisted lap/ In the front row outboard seats, the shoulder belt can be shoulder belt. adjusted upward or downward to help position the belt away from your neck. Press the button located on the 1. Position the latch plate as close as possible to the upper belt guide, and then move it up or down to the anchor point.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 As a guide, if you are shorter than average you will prefer a lower position, and if you are taller than average you will prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position. Center Lap Belts The center seating position for the Quad Cab®, Mega Cab® and Crew Cab front seat has a lap belt only. To fasten the lap belt, slide the latch plate into the buckle until you hear a “click”.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE For Quad Cab®, Mega Cab® and Crew Cab Only First Row Second Row Driver N/A ALR Center Cinch Cinch Passenger ALR ALR • N/A — Not Applicable • ALR — Automatic Locking Retractor Automatic Locking Retractor (ALR) Mode – If Equipped For Standard Cab Only First Row Second Row Driver N/A N/A Only pull the belt webbing out far enough to comfortably wrap around the occupant’s mid-section so as to not activate the ALR.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 How To Engage The Automatic Locking Mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the Automatic Locking Mode.
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Pretensioners Enhanced Seat Belt Use Reminder System The seat belts for both front seating positions are (BeltAlert®) equipped with pretensioning devices that are designed to BeltAlert® is a feature intended to remind the driver and remove slack from the seat belt in the event of a collision. front passenger (if equipped with front passenger These devices may improve the performance of the seat BeltAlert®) to fasten their seat belts.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 unbuckled while traveling at speeds greater than 5 mph Seat Belts And Pregnant Women (8 km/h), BeltAlert® will provide both audio and visual We recommend that pregnant women use seat belts notification. throughout their pregnancies. Keeping the mother safe is The front passenger seat BeltAlert® is not active when the best way to keep the baby safe. the front passenger seat is unoccupied.
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use when the seat belt is not long enough when it is worn low and snug and in the recommended seating positions. Remove and store the extender when not needed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 This vehicle may also be equipped with Supplemental Seat-Mounted Side Air Bags (SAB) to provide enhanced protection for an occupant during a side impact. If the vehicle is equipped with Supplemental Seat-Mounted Side Air Bags they are located in the outboard side of the This vehicle may be equipped with a driver and/or front front seats. passenger seat belt buckle switch that detects whether the driver or front passenger seat belt is fastened.
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag System Components • Seat Belt Buckle Switch Your vehicle may be equipped with the following air bag • Seat Belt Pretensioners system components: Advanced Front Air Bag Features • Occupant Restraint Controller (ORC) The Advanced Front Air Bag system has multistage • Air Bag Warning Light driver and front passenger air bags.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 WARNING! • No objects should be placed over or near the air bag on the instrument panel, because any such objects could cause harm if the vehicle is in a collision severe enough to cause the air bag to inflate. • Do not put anything on or around the air bag covers or attempt to open them manually. You may damage the air bags and you could be injured because the air bags may no longer be functional.
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Side Air Bag Inflatable Curtain (SABIC) — If Equipped SABIC air bags may offer side-impact protection to front and rear seat outboard occupants in addition to that provided by the body structure. Each air bag features inflated chambers placed adjacent to the head of each outboard occupant that reduce the potential for sideimpact head injuries. The curtains deploy downward, covering both windows on the impact side.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 • Being too close to the SAB and SABIC air bags during deployment could cause you to be severely injured or killed. • Should a vehicle rollover occur, the pretensioners (if equipped) and/or SAB and SABIC air bags on both sides of the vehicle may deploy. The system includes side impact sensors (if equipped) that are calibrated to deploy the side air bags during impacts that require air bag occupant protection.
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • If your vehicle is equipped with left and right Supplemental Side Air Bag Inflatable Curtain (SABIC), do not stack luggage or other cargo up high enough to block the location of the SABIC. The area where the SABIC is located should remain free from any obstructions.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Along with seat belts and pretensioners, Advanced Front Air Bags work with the knee impact bolsters to provide improved protection for the driver and front passenger. Side air bags also work with seat belts to improve occupant protection.
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Because air bag sensors measure vehicle deceleration over time, vehicle speed and damage by themselves are not good indicators of whether or not an air bag should have deployed. Also, the ORC turns on the Air Bag Warning Light in the instrument panel for approximately four to eight seconds for a self-check when the ignition is first turned on. After the self-check, the Air Bag Warning Light will turn off.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 WARNING! Ignoring the Air Bag Warning Light in your instrument panel could mean you won’t have the air bags to protect you in a collision. If the light does not come on as a bulb check when the ignition is first turned on, stays on after you start the vehicle, or if it comes on as you drive, have an authorized dealer service the air bag system immediately.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Based on the severity and type of collision, the side air bag inflator on the crash side of the vehicle may be triggered, releasing a quantity of non-toxic gas. The inflating SAB exits through the seat seam into the space between the occupant and the door. The SAB fully inflate in about 10 milliseconds.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 In order to reset the Enhanced Accident Response System functions after an event, the ignition switch must be In the event of an impact causing air bag deployment, if changed from IGN ON to IGN OFF. the communication network remains intact, and the power remains intact, depending on the nature of the 9-1-1 Call Operating Instructions – If Equipped event the ORC will determine whether to have the 1.
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Once a connection between the vehicle and a 9-1-1 operator is made, the 9-1-1 Call system may transmit the following important vehicle information to a 9-1-1 operator: NOTE: Once a connection is made between the vehicle’s 9-1-1 Call system and the 9-1-1 operator, the 9-1-1 operator may be able to open a voice connection with the vehicle to determine if additional help is needed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 WARNING! WARNING! (Continued) • If anyone in the vehicle could be in danger (e.g., fire or smoke is visible, dangerous road conditions or location), do not wait for voice contact from a 9-1-1 operator. All occupants should exit the vehicle immediately and move to a safe location. • The 9-1-1 Call system is embedded into the vehicle’s electrical system. Do not add aftermarket electrical equipment to the vehicle’s electrical system.
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Phone Screen will display the following message Even if the 9-1-1 Call system is fully functional, factors “Vehicle phone requires service. Please contact your beyond FCA US LLC’s control may prevent or stop the dealer.”; and, 9-1-1 Call system operation. These include, but are not limited to, the following factors: • An In-Vehicle Audio message will state “Vehicle phone requires service. Please contact your dealer.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 • Operator error by the 9-1-1 operator; If A Deployment Occurs • Wireless network congestion; The Advanced Front Air Bags are designed to deflate immediately after deployment. • Weather; and NOTE: In a rollover the pretensioners and/or SAB and SABIC - if equipped air bags may deploy on both sides of NOTE: Never place anything on or near the vehicle’s the vehicle. wireless and GPS antennas.
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE However, if you haven’t healed significantly within a few days, or if you have any blistering, see your doctor immediately. WARNING! Deployed air bags and seat belt pretensioners cannot protect you in another collision. Have the air bags, seat belt pretensioners, and the front seat belt retractor assemblies replaced by an authorized dealer immediately. Also, have the Occupant Restraint Controller (ORC) system serviced as well.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 WARNING! (Continued) WARNING! (Continued) upper right side of the instrument panel. Do not modify the front bumper, vehicle body structure, or add aftermarket side steps or running boards. • It is dangerous to try to repair any part of the air bag system yourself. Be sure to tell anyone who works on your vehicle that it has an air bag system. • Do not attempt to modify any part of your air bag system.
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The Air Bag Warning Light remains on after the four to Event Data Recorder (EDR) eight-second interval. This vehicle is equipped with an event data recorder • The Air Bag Warning Light comes on intermittently or (EDR). The main purpose of an EDR is to record, in certain crash or near crash-like situations, such as an air remains on while driving.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 These data can help provide a better understanding of Child Restraints the circumstances in which crashes and injuries occur. Everyone in your vehicle needs to be buckled up at all NOTE: EDR data are recorded by your vehicle only if a times, including babies and children.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards. You should also make sure that you can install it in the vehicle where you will use it. NOTE: For additional information, refer to www.seatcheck.org or call 1–866–SEATCHECK. Canadian residents should refer to Transport Canada’s website for additional information: http://www.tc.gc.ca/ eng/roadsafety/safedrivers-childsafety-index-53.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 Summary Of Recommendations For Restraining Children In Vehicles Infants and Toddlers Small Children Larger Children Children Too Large for Child Restraints Child Size, Height, Weight or Age Children who are two years old or younger and who have not reached the height or weight limits of their child restraint Children who are at least two years old or who have out-grown the height or weight limit of their rear-facing child restraint Children who have out-g
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Infants And Child Restraints Safety experts recommend that children ride rearwardfacing in the vehicle until they are two years old or until they reach either the height or weight limit of their rear facing child safety seat. Two types of child restraints can be used rearward-facing: infant carriers and convertible child seats. The infant carrier is only used rearward-facing in the vehicle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 remain in a forward-facing child seat with a harness for as long as possible, up to the highest weight or height allowed by the child seat. All children whose weight or height is above the forward-facing limit for the child seat should use a belt-positioning booster seat until the vehicle’s seat belts fit properly.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Is the lap part of the belt as low as possible, touching the child’s thighs and not their stomach? Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend 5. Can the child stay seated like this for the whole trip? over the front of the seat when their back is against the seatback, should use the seat belt in a rear seat.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 89 Recommendations For Attaching Child Restraints — Quad Cab®/Crew Cab Restraint Type Combined Weight of the Child + Child Restraint Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
90 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Recommendations For Attaching Child Restraints — Standard Cab, Mega Cab® Restraint Type Combined Weight of the Child + Child Restraint Rear-Facing Child Restraint Rear-Facing Child Restraint Forward-Facing Child Restraint Forward-Facing Child Restraint Up to 65 lbs (29.5 kg) More than 65 lbs (29.5 kg) Up to 65 lbs (29.5 kg) More than 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 91 Lower Anchors and Tethers for Children (LATCH) Restraint System Your vehicle is equipped with the child restraint anchorage system called LATCH, which stands for Lower Anchors and Tethers for CHildren. The LATCH system has three vehicle anchor points for installing LATCHequipped child seats. There are two lower anchorages located at the back of the seat cushion where it meets the seatback and one top tether anchorage located behind the seating position.
92 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE LATCH Positions For Installing Child Restraints In This Vehicle Quad Cab®/Crew Cab Full Bench Standard Cab Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 93 2 Mega Cab®/Crew Cab Split Bench Lower Anchorage Symbol 2 anchorages per seating position Top Tether Anchorage Symbol
94 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Quad Cab®/Crew Cab What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 95 Can two child restraints be attached using a common lower LATCH anchorage? No Can the rear-facing child restraint touch the back of the front passenger seat? Yes Can the head restraints be removed? No Never “share” a LATCH anchorage with two or more child restraints.
96 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Mega Cab®/Standard Cab What is the weight limit (child’s weight + weight of the child restraint) for using the LATCH anchorage system to attach the child restraint? 65 lbs (29.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 97 Can the rear-facing child restraint touch the back of the front passenger seat? Can the head restraints be removed? Yes No The child seat may touch the back of the front passenger seat if the child restraint manufacturer also allows contact. See your child restraint owner’s manual for more information.
98 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Locating The LATCH Anchorages — Quad Cab®/Mega Cab®/Crew Cab The lower anchorages are round bars that are found at the rear of the seat cushion where it meets the seatback. They are just visible when you lean into the rear seat to install the child restraint. You will easily feel them if you run your finger along the gap between the seatback and seat cushion.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 99 Locating The LATCH Anchorages In addition, Regular Cab models have tether strap anchorages behind the front center and right seats. Quad Cab®, Mega Cab® and Crew Cab models have tether strap anchorages located behind each of the rear seats.
100 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE tether strap. The tether strap will have a hook at the end to attach to the top tether anchorage and a way to tighten the strap after it is attached to the anchorage. Center Seat LATCH — Standard Cab/Quad Cab®/Crew Cab Full Bench Do not install a child restraint in the center position using the LATCH system. Use the seat belt and tether anchor to install a child seat in the center seating position.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 101 Center Seat LATCH — Mega Cab®/Crew Cab Split Bench If a child restraint installed in the center position blocks the seat belt webbing or buckle for the outboard position, do not use that outboard position. If a child seat in the center position blocks the outboard LATCH anchors or seat belt, do not install a child seat in that outboard position. WARNING! Never use the same lower anchorage to attach more than one child restraint.
102 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Attach the lower hooks or connectors of the child How To Stow An Unused ALR Seatbelt restraint to the lower anchorages in the selected seat- When using the LATCH attaching system to install a ing position. child restraint, stow all ALR seat belts that are not being 5. If the child restraint has a tether strap, connect it to the used by other occupants or being used to secure child top tether anchorage. See the section “Installing Child restraints.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 103 the seat belt tight around the child restraint so that it is not necessary to use a locking clip. The ALR retractor can Improper installation of a child restraint to the be “switched” into a locked mode by pulling all of the LATCH anchorages can lead to failure of the re- webbing out of the retractor and then letting the webbing straint. The child could be badly injured or killed. retract back into the retractor.
104 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Systems for Installing Child Restraints in this Vehicle Quad Cab®/Mega Cab®/Crew Cab Standard Cab
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 105 Quad Cab®/Crew Cab What is the weight limit (child’s weight + weight of the child restraint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? Can the rear-facing child restraint touch the back of the front passenger seat? Weight limit of the Child Restraint Can the head restraints be removed? Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint? No Yes Yes Always u
106 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Mega Cab®/Standard Cab What is the weight limit (child’s weight + weight of the child restraint) for using the Tether Anchor with the seat belt to attach a forward facing child restraint? Can the rear-facing child restraint touch the back of the front passenger seat? Weight limit of the Child Restraint Can the head restraints be removed? Can the buckle stalk be twisted to tighten the seat belt against the belt path of the child restraint? No Yes Yes Alwa
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 107 Installing A Child Restraint with a Switchable Automatic Locking Retractor (ALR) back into the retractor. As the webbing retracts, you will hear a clicking sound. This means the seat belt is now in the Automatic Locking mode. 1. Place the child seat in the center of the seating position. For some second row seats, you may need to 6. Try to pull the webbing out of the retractor.
108 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 9. Test that the child restraint is installed tightly by 3. Slide the latch plate into the buckle until you hear a “click.” pulling back and forth on the child seat at the belt path. It should not move more than 1 inch (25.4 mm) 4. Finally, pull up on any excess webbing to tighten the in any direction.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 109 Any seat belt system will loosen with time, so check the Installing Child Restraints Using The Top Tether belt occasionally, and pull it tight if necessary. Anchorage If the buckle or the cinching latch plate is too close to the belt path opening of the child restraint, you may have trouble tightening the seat belt. If this happens, disconnect the latch plate from the buckle and twist the short buckle-end belt up to three full turns to shorten it.
110 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Route the tether strap to provide the most direct path between the anchorage and the child seat. The tether strap should go between the head restraint posts underneath the head restraint. You may need to adjust the head restraint to the upward position to pass the tether strap underneath the head restraint and between its posts. 3. Lift the cover (if so equipped), and attach the hook to the square opening in the sheet metal.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 111 WARNING! (Continued) younger, including a child in a rearward facing infant seat. Quad Cab® or Crew Cab Trucks: The top tether anchorages in this vehicle are tether strap loops located between the rear glass and the back of the rear seat. There is a tether strap loop located behind each seating position. Follow the steps below to attach the tether strap of the child restraint.
112 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Right or Left Outboard Seats: 1. Raise the head restraint and reach between the rear seat and rear glass to access the tether strap loop. Tether Strap Loop With Center Head Restraint In Raised Position Head Restraint In Raised Position 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 113 3. Pass the tether strap hook under the head restraint 4. Attach the hook to the center tether strap loop (see behind the child seat, though the tether strap loop diagram). Tighten the tether strap according to the behind the seat and over to the center tether strap child seat manufacturer’s instructions. loop.
114 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If there are child seats in both of the outboard (left and right) seating positions, the tether strap hooks of both child seats should be connected to the center tether strap loop. This is the correct way to tether two outboard child seats. Center Seat: 1. Raise the head restraint and reach between the rear seat and rear glass to access the tether strap loop. Tether Strap Loop With Head Restraint In Raised Position 2.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 115 3. Pass the tether strap hook under the head restraint 4. Attach the hook to the outboard tether strap loop (see behind the child seat, though the tether strap loop diagram). Tighten the tether strap according to the behind the seat and over to the right or left outboard child seat manufacturer’s instructions. tether strap loop.
116 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing Three Child Restraints: 1. Place a child restraint on each outboard rear seat. Route the tether straps following the directions for right and left seating positions, above. 2. Attach both hooks to the center tether strap loop, but do not tighten the straps yet. 3. Place a child restraint on the center rear seat. Route the tether strap following the directions for the center seating position, above. 4.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 117 WARNING! • An incorrectly anchored tether strap could lead to increased head motion and possible injury to the child. Use only the anchorage position directly behind the child seat to secure a child restraint top tether strap. • If your vehicle is equipped with a split rear seat, make sure the tether strap does not slip into the opening between the seatbacks as you remove slack in the strap.
118 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! WARNING! Never use Non-Detergent Oil or Straight Mineral Oil in the engine or damage may result. • Do not leave children or animals inside parked vehicles in hot weather. Interior heat build-up may cause serious injury or death. • It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 119 Exhaust Gas WARNING! (Continued) WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing (CO), follow these safety tips: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
120 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Defroster Check operation by selecting the defrost mode and place the blower control on high speed. You should be able to Inspect the belt system periodically, checking for cuts, feel the air directed against the windshield. See your frays, and loose parts. Damaged parts must be replaced authorized dealer for service if your defroster is inoperimmediately. Do not disassemble or modify the system. able.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 121 WARNING! WARNING! (Continued) Pedals that cannot move freely can cause loss of vehicle control and increase the risk of serious personal injury. • Always make sure that floor mats are properly attached to the floor mat fasteners. • Never place or install floor mats or other floor coverings in the vehicle that cannot be properly secured to prevent them from moving and interfering with the pedals or the ability to control the vehicle.
122 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Periodic Safety Checks You Should Make Outside The Vehicle Fluid Leaks Check area under vehicle after overnight parking for fuel, engine coolant, oil, or other fluid leaks. Also, if gasoline fumes are detected or if fuel, power steering fluid Examine tires for excessive tread wear and uneven wear (2500,3500,4500,5500 Models Only), or brake fluid leaks patterns.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS 䡵 MIRRORS . . . . . . . . . . . . . . . . . . . . . . . . . . . .129 ▫ Inside Day/Night Mirror . . . . . . . . . . . . . . . .129 ▫ Automatic Dimming Mirror — If Equipped . . .130 ▫ Automatic Dimming Mirror With Rear View Camera Display — If Equipped . . . . . . . . . . .131 ▫ Outside Mirrors . . . . . . . . . . . . . . . . . . . . . .132 ▫ Driver’s Outside Automatic Dimming Mirror — If Equipped. . . . . . . . . . . . . . . . . . . . . . . . . .
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ Ventilated Seats — If Equipped . . . . . . . . . . . .145 ▫ Automatic Headlights — If Equipped . . . . . . .161 ▫ Manual Seat Adjuster — If Equipped. . . . . . . .146 ▫ Headlights On With Wipers (Available With Automatic Headlights Only) . . . . . . . . . . . . . .162 ▫ 40-20-40 Front Bench Seat — If Equipped . . . .148 ▫ Mega Cab® Rear Seat Features . . . . . . . . . . . .148 ▫ Head Restraints . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 ▫ Multifunction Lever . . . . . . . . . . . . . . . . . . .169 䡵 HEATED STEERING WHEEL — IF EQUIPPED . . . . . . . . . . . . . . . . . . ▫ Turn Signals . . . . . . . . . . . . . . . . . . . . . . . . .170 䡵 DRIVER ADJUSTABLE PEDALS — ▫ Lane Change Assist . . . . . . . . . . . . . . . . . . .170 IF EQUIPPED . . . . . . . . . . . . . . . . . . ▫ Flash-To-Pass . . . . . . . . . . . . . . . . . . . . . . . .170 䡵 ELECTRONIC SPEED CONTROL . . . .
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ▫ ParkSense® Warning Display . . . . . . . . . . . . .183 ▫ Courtesy/Reading Lights . . . . . . . . . . . . . . .194 ▫ ParkSense® Display . . . . . . . . . . . . . . . . . . . .183 䡵 GARAGE DOOR OPENER — IF EQUIPPED. . . .195 ▫ Enabling And Disabling ParkSense® . . . . . . .186 ▫ Before You Begin Programming HomeLink® . .196 ▫ Service The ParkSense® Rear Park Assist System . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 ▫ Pinch Protect Feature . . . . . . . . . . . . . . . . . . .205 ▫ Rear Cupholder — Quad Cab®. . . . . . . . . . . .214 ▫ Venting Sunroof — Express . . . . . . . . . . . . . .205 ▫ Rear Cupholder — Crew Cab . . . . . . . . . . . . .214 ▫ Sunshade Operation. . . . . . . . . . . . . . . . . . . .206 䡵 STORAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . .215 ▫ Wind Buffeting . . . . . . . . . . . . . . . . . . . . . . .206 ▫ Glove Box Storage . . .
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 䡵 REAR WINDOW FEATURES . . . . . . . . . . . . . .224 ▫ Bed Rail Tie-Down System . . . . . . . . . . . . . .241 ▫ Rear Window Defroster . . . . . . . . . . . . . . . . .224 䡵 SLIDE-IN CAMPERS . . . . . . . . . . . . . . . . . . . .243 ▫ Power Sliding Rear Window — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .225 ▫ Manual Sliding Rear Window — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 MIRRORS Inside Day/Night Mirror A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the windshield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window.
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror — If Equipped A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the windshield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Automatic Dimming Mirror With Rear View Camera Display — If Equipped A single ball joint mirror is provided in the vehicle. It is a twist on mirror that has a fixed position at the windshield. The mirror installs on the windshield button with a counterclockwise rotation and requires no tools for mounting. The mirror head can be adjusted up, down, left, and right for various drivers. The mirror should be adjusted to center on the view through the rear window.
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirrors Outside Mirrors Folding Feature To receive maximum benefit, adjust the outside mirrors All outside mirrors are designed to be able to be manuto center on the adjacent lane of traffic with a slight ally folded both forward and rearward to prevent damoverlap of the view obtained on the inside mirror. age. WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 CAUTION! It is recommended to fold the mirrors into the full rearward position to resist damage when entering a car wash or a narrow location. If the mirror is manually folded after electrically cycled, a potential extra button push is required to get the mirrors back to the home position. If the mirror does not electrically fold check for ice or dirt build up at the pivot area which can cause excessive drag.
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The power mirror controls consist of mirror select butThe controls for the power mirrors are located on the tons and a four-way mirror control switch. driver’s door trim panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 To adjust a mirror, press either the L (left) or R (right) Heated Mirrors — If Equipped button to select the mirror that you want to adjust. Using the mirror control switch, press on any of the four arrows for the direction that you want the mirror to move These mirrors are heated to melt frost or ice. This feature can be activated whenever you turn on the rear window defroster if equipped.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Illuminated Vanity Mirror — If Equipped “Slide-On-Rod” Features Of Sun Visor — Illuminated vanity mirrors are located on each sun visor. If Equipped To use the mirror, rotate the sun visor down and swing The sun visor “Slide-On-Rod” feature allows for addithe mirror cover upward. The lights will turn on auto- tional flexibility in positioning the visor to block out the sun. matically. Closing the mirror cover turns off the light.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or outboard, the mirror head should be rotated (flipped in or out).
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Fold the trailer towing mirrors rearward prior to SEATS entering an automated car wash. Seats are a part of the Occupant Restraint System of the A small blindspot mirror is located next to main mirror vehicle. and can be adjusted separately. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Driver’s Power Seat — If Equipped Some models may be equipped with an eight-way power driver’s seat. The power seat switches are located on the outboard side of the driver’s seat cushion. There are two power seat switches that are used to control the movement of the seat cushion and the seatback.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjusting The Seat Forward Or Rearward Reclining The Seatback The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch. Release the switch when the desired position has been reached. The angle of the seatback can be adjusted forward or rearward. Push the seatback switch forward or rearward, the seat will move in the direction of the switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 CAUTION! Do not place any article under a power seat or impede its ability to move as it may cause damage to the seat controls. Seat travel may become limited if movement is stopped by an obstruction in the seat’s path. Adjusting The Seat Forward Or Rearward The seat can be adjusted both forward and rearward. Push the seat switch forward or rearward, the seat will move in the direction of the switch.
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Lumbar — If Equipped Vehicles equipped with power driver or passenger seats may be also be equipped with power lumbar. The power lumbar switch is located on the outboard side of the power seat. Push the switch forward to increase the lumbar support. Push the switch rearward to decrease the lumbar support.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 Heated Seats — If Equipped Front Heated Seats On some models, the front and rear seats may be There are two heated seat switches as well as soft-keys in equipped with heaters located in the seat cushions. the radio that allow the driver and passenger to operate the seats independently. The controls for each seat are located near the bottom center of the instrument panel WARNING! (below the climate controls) or in the radio unit.
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Vehicle Equipped With Remote Start • Once a heat setting is selected, heat will be felt within On models that are equipped with remote start, the driver’s heated seat can be programmed to come on two to five minutes. during a remote start. Refer to “Remote Starting System • The engine must be running for the heated seats to — If Equipped” in “Things to Know Before Starting Your operate. Vehicle” for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 There are two heated seat switches that allow the rear passengers to operate the seats independently. You can choose from HIGH, LOW or OFF heat settings. Amber indicator lights in each switch indicate the level of heat in use. Two indicator lights will illuminate for HIGH, one for LOW and none for OFF. of operation. Then, the heat output will drop to the normal HIGH-level.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press the switch once to choose HIGH, press it a second time to choose LOW. Pressing the switch a third time will turn the ventilated seat OFF. When HIGH speed is selected both lights on the switch will be illuminated. When LOW speed is selected one light will Manual Seat Adjuster — If Equipped Both front seats are adjustable forward or rearward. The manual seat adjustment handle is located under the seat cushion at the front edge of each seat.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 While sitting in the seat, pull up on the handle and slide the seat forward or backward. Release the bar once you have reached the desired position. Then, using body pressure, move forward and rearward on the seat to be sure that the seat adjusters have latched. Dump Feature — Manual Recline Seat Only Actuating the recliner handle will allow the seatback to swing (dump) forward on manual recliner seats.
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 40-20-40 Front Bench Seat — If Equipped The seat is divided into three segments. The outboard seat portions are each 40% of the total width of the seat. On some models the back of the center portion (20%) easily folds down to provide an armrest/center storage compartment. Mega Cab® Rear Seat Features Reclining Rear Seats — If Equipped The recliner handle is located on the outside of the seat cushion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 Folding Rear Seat (Table Mode) — If Equipped 2. Fold the seatback forward. Both the left and right rear seatbacks can be folded down and used as a table. To fold down either rear seatback: 3 1. Lift the handle, located next to the head restraint. Table Mode 3. Lift the seatback, to return the seat to the upright position. Be sure the seatback is locked in place.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Folding Rear Seat — If Equipped To fold either rear seat flat: Both the outboard rear seats will drop and move forward 1. Lift the handle, located on the outboard side of either when the seatback is folded flat. of the rear seats. WARNING! • It is dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 2. Fold the seatback down and push the seat forward. WARNING! An improperly latched seat could cause serious injury or death. Make sure that the seatback is securely locked into position. If the seatback in not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. Rear Passenger Fold-Flat Seats 3. Lift the seatback, to return the seat to the upright position. Be sure the seat is locked in place.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Head Restraints Front Head Restraints Head restraints are designed to reduce the risk of injury by restricting head movement in the event of a rear impact. Head restraints should be adjusted so that the top of the head restraint is located above the top of your ear. To raise the head restraint, pull upward on the head restraint.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Rear Head Restraints NOTE: The rear seats are equipped with adjustable head re- • The rear center head restraint (Crew Cab and Quad straints. To raise the head restraint, pull upward on the Cab) has only one adjustment position that is used to head restraint. To lower the head restraint, press the aid in the routing of a tether.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER MEMORY SEAT — IF EQUIPPED This feature allows the driver to store up to two different memory profiles for easy recall through a memory switch. Each memory profile contains desired position settings for the driver seat, side mirrors, adjustable pedals (if equipped) and a set of desired radio station presets. Your Remote Keyless Entry (RKE) transmitter can also be programmed to recall the same positions when the UNLOCK button is pressed.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Programming The Memory Feature Vehicles Not Equipped With Keyless Enter-N-Go NOTE: To create a new memory profile, perform the 1. Insert the ignition key fob, and turn the ignition switch following: to the ON/RUN position. 2.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Before programming your RKE transmitters you must select the “Remote Linked to Memory” feature • Memory profiles can be set without the vehicle in through the Electronic Vehicle Information Center PARK, but the vehicle must be in PARK to recall a (EVIC), refer to “Electronic Vehicle Information Center memory profile.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 3. Once the profile has been recalled, press and release the SET (S) button on the memory switch, then press and release button (1) or (2) accordingly. “Memory Profile Set” (1 or 2) will display in the instrument cluster on vehicles equipped with the EVIC. Memory Position Recall NOTE: The vehicle must be in PARK to recall memory positions.
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver Two Memory Position Recall TO OPEN AND CLOSE THE HOOD • To recall the memory setting for driver two using the To open the hood, two latches must be released. memory switch, press MEMORY button number 2 on 1. Pull the hood release lever located below the steering the memory switch. wheel at the base of the instrument panel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 2. Reach into the opening beneath the center of the hood and push the safety latch lever to the left to release it, before raising the hood. CAUTION! To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. WARNING! Be sure the hood is fully latched before driving your vehicle.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your vehicle is equipped with plastic headlight and fog light (if equipped) lenses that are lighter and less susceptible to stone breakage than glass lights. Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. LIGHTS The headlight switch is located on the left side of the instrument panel, next to the steering wheel.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Headlights To turn on the headlights, rotate the headlight switch clockwise to the headlight position. When the headlight switch is on, the parking lights, taillights, license plate light and instrument panel lights are also turned on. To turn off the headlights, rotate the headlight switch back to the O (Off) position.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights On With Wipers (Available With Automatic Headlights Only) DRL lamp on the same side of the vehicle may turn off for the duration of the turn signal activation. Once the turn signal is no longer active, the DRL lamp will illuminate. When this feature is active, the headlights will turn on approximately 10 seconds after the wipers are turned on Headlight Delay if the headlight switch is placed in the AUTO position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 • Broken, muddy, or obstructed headlights and taillights of vehicles in the field of view will cause headlights to remain on longer (closer to the vehicle). Also, dirt, film, The Automatic High Beam Headlamp Control system and other obstructions on the windshield or camera provides increased forward lighting at night by automatlens will cause the system to function improperly.
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Rotate the headlight switch counterclockwise to the 2. Pull the multifunction lever toward you to switch the headlights from the high beam to the low beam AUTO (A) position. position. 3. Push the multifunction lever away from you to switch the headlights to the high beam position. Refer to 3. Rotate the headlight switch clockwise from the AUTO (A) to the on position. “Multifunction Lever” in this section for further information.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 The fog lights will operate only when the parking lights The fog lights are turned on by rotating the headlight are on or when the vehicle headlights are on low beam. switch to the parking light or headlight position and An indicator light located in the instrument cluster will illuminate when the fog lights are on. The fog lights will pushing in the headlight rotary control.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE button is pressed on the Remote Keyless Entry (RKE) transmitter. When a door is open and the interior lights are on, rotating the dimmer control all the way left, to the OFF detent, will cause all the interior lights to go out.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 (RKE) transmitter, if equipped. These lights are also operated individually as reading lights by pressing on the corresponding lens.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Ambient Light The overhead console is equipped with an ambient light feature. This light casts illumination for improved visibility of the floor console area. Rear Passenger Courtesy/Reading Light NOTE: The courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 The cargo lights will also turn on for approximately 30 The cargo lights are turned on by pressing on the cargo seconds when a RKE transmitter UNLOCK button is pressed, as part of the Illuminated Entry feature. button. Multifunction Lever Cargo Light The multifunction lever is located on the left side of the steering column.
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: If either light remains on and does not flash, or Move the multifunction lever up or down and the arrows there is a very fast flash rate, check for a defective outside on each side of the instrument cluster flash to show light bulb. If an indicator fails to light when the lever is moved, it would suggest that the indicator bulb is proper operation of the front and rear turn signal lights. defective.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 High/Low Beam Switch WINDSHIELD WIPERS AND WASHERS Push the multifunction lever toward the instrument Windshield Wipers panel to switch the headlights to high beam. Pulling the The wipers and washers are operated by a switch in the multifunction lever back toward the steering wheel will multifunction lever. Turn the end of the handle to select turn the low beams back on, or shut the high beams off. the desired wiper speed.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wiper Operation Windshield Washers Rotate the end of the lever upward, to the first detent past the intermittent settings for low-speed wiper operation. Rotate the end of the lever upward to the second detent past the intermittent settings for high-speed wiper operation. To use the windshield washer, push the washer knob, located on the end of the multifunction lever, inward to the second detent.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 WARNING! Sudden loss of visibility through the windshield could lead to a collision. You might not see other vehicles or other obstacles. To avoid sudden icing of the windshield during freezing weather, warm the windshield with the defroster before and during windshield washer use.
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Rain Sensing feature may not function properly when ice, or dried salt water is present on the windshield. operate until the wiper switch is moved, vehicle speed is greater than 0 mph (0 km/h), or the outside temperature is greater than 32°F (0°C). • Use of Rain-X® or products containing wax or silicone • Transmission In NEUTRAL Position — When the may reduce Rain Sensing performance.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 TILT STEERING COLUMN This feature allows you to tilt the steering column upward or downward. The tilt lever is located on the steering column, below the multifunction lever. 3 Pull the lever toward the steering wheel to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Release the lever to lock the steering column firmly in place.
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driving with the steering column unlocked, could cause the driver to lose control of the vehicle. Failure to follow this warning may result in serious injury or death. HEATED STEERING WHEEL — IF EQUIPPED The heated steering wheel switch is located on the switch bank below the climate controls.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 Vehicles Equipped With Remote Start WARNING! (Continued) On models that are equipped with remote start, the heated steering wheel can be programmed to come on during a remote start. Refer to “Remote Starting System — If Equipped” in “Things to Know Before Starting Your Vehicle” for further information. • Do not place anything on the steering wheel that insulates against heat, such as a blanket or steering wheel covers of any type and material.
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The adjustable pedal switch is located to the left side of • The pedals cannot be adjusted when the vehicle is in the steering column. REVERSE or when the Electronic Speed Control System is on.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 CAUTION! The Electronic Speed Control buttons are located on the right side of the steering wheel. Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. 3 WARNING! Do not adjust the pedals while the vehicle is moving. You could lose control and have an accident.
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In order to ensure proper operation, the Electronic Speed Control System has been designed to shut down if multiple Speed Control functions are operated at the same time. If this occurs, the Electronic Speed Control System can be reactivated by pushing the Electronic Speed Control ON/OFF button and resetting the desired vehicle set speed. WARNING! Leaving the Electronic Speed Control system on when not in use is dangerous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 Pressing the RES (+) button once will result in a 1 mph (1.6 km/h) increase in set speed. Each subsequent tap of A soft tap on the brake pedal, pushing the CANCEL the button results in an increase of 1 mph (1.6 km/h). button, or normal brake pressure while slowing the vehicle will deactivate Electronic Speed Control without To decrease speed while the Electronic Speed Control is erasing the set speed memory. Pressing the ON/OFF set, push the SET (-) button.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using Electronic Speed Control On Hills PARKSENSE® REAR PARK ASSIST — The transmission may downshift on hills to maintain the IF EQUIPPED The ParkSense® Rear Park Assist system provides visual vehicle set speed. and audible indications of the distance between the rear NOTE: The Electronic Speed Control system maintains fascia and a detected obstacle when backing up, e.g. speed up and down hills. A slight speed change on during a parking maneuver.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 ParkSense® Sensors The ParkSense® Warning screen is located within the Electronic Vehicle Information Center (EVIC). It provides visual warnings to indicate the distance between the rear fascia/bumper and the detected obstacle. Refer to “Electronic Vehicle Information Center (EVIC)/Settings” in Understanding Your Instrument Panel” for further information.
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE As the vehicle moves closer to the object, the display will show the single arc moving closer to the vehicle and the tone will change from a single 1/2 second tone to slow, to fast, to continuous.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 3 Fast Tone Continuous Tone The vehicle is close to the obstacle when the warning display shows one flashing arc and sounds a continuous tone.
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Distance (in/cm) Audible Alert Chime Arc Greater than 79 in (200 cm) None Radio Volume Reduced No None WARNING ALERTS 79-45 in 45-31 in (200-115 cm) (115-80 cm) Single 1/2 Slow Second Tone 4th Solid 3rd Solid Yes Yes 31-18 in (80-45 cm) Fast Less than 18 in (45 cm) Continuous 2nd Flashing Yes 1st Flashing Yes NOTE: ParkSense® will reduce the volume of the radio, approximately five seconds.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 NOTE: The ParkSense® system will automatically disable when the system detects that a trailer with trailer brakes has been connected to the Integrated Trailer Brake Module. The EVIC will display “PARKSENSE OFF” message for as long as the vehicle is in reverse. The ParkSense® switch LED will be ON when ParkSense® is disabled or defective. The ParkSense® switch LED will be OFF when the system is enabled.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If ⬙PARKSENSE UNAVAILABLE WIPE REAR SENSORS⬙ ParkSense® System Usage Precautions appears in the Electronic Vehicle Information Center NOTE: (EVIC) make sure the outer surface and the underside of the rear fascia/bumper is clean and clear of snow, ice, • Ensure that the rear bumper is free of snow, ice, mud, dirt and debris to keep the ParkSense® system opermud, dirt or other obstruction, and then cycle the igniating properly. tion.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 • ParkSense® , when on, will reduce the volume of the • On vehicles equipped with a tailgate, ParkSense® radio when it is sounding a tone. should be disabled when the tailgate is in the lowered or open position and the vehicle is in REVERSE. A • Clean the ParkSense® sensors regularly, taking care lowered tailgate could provide a false indication that not to scratch or damage them. The sensors must not an obstacle is behind the vehicle.
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Drivers must be careful when backing up even when using ParkSense®. Always check carefully behind your vehicle, look behind you, and be sure to check for pedestrians, animals, other vehicles, obstructions, and blind spots before backing up. You are responsible for safety and must continue to pay attention to your surroundings. Failure to do so can result in serious injury or death.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 When the vehicle is shifted out of REVERSE, the rear camera mode is exited. Active guide lines are overlaid on the image to illustrate the width of the vehicle and its projected backup path based on the steering wheel position. The active guide lines will show separate zones that will help indicate the distance to the rear of the vehicle.
192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! • To avoid vehicle damage, ParkView® should only be used as a parking aid. The ParkView® camera is unable to view every obstacle or object in your drive path. • To avoid vehicle damage, the vehicle must be driven slowly when using ParkView® to be able to stop in time when an obstacle is seen. It is recommended that the driver look frequently over his/her shoulder when using ParkView®. Turning ParkView® On Or Off — With Uconnect® 5.0 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193 OVERHEAD CONSOLE — IF EQUIPPED The overhead console is located on the headliner above the review mirror.
194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Courtesy/Reading Lights Both lights in the overhead console and rear passenger compartment will illuminate as courtesy lights when a door is opened, when the dimmer control is rotated to the courtesy light position (full right position), or when the UNLOCK button is pressed on the Remote Keyless Entry (RKE) transmitter, if equipped. These lights are also operated individually as reading lights by pressing on the corresponding lens.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195 GARAGE DOOR OPENER — IF EQUIPPED HomeLink® replaces up to three hand-held transmitters that operate devices such as garage door openers, motorized gates, lighting or home security systems. The HomeLink® unit is powered by your vehicles 12 Volt battery. Rear Passenger Courtesy/Reading Light NOTE: The courtesy/reading lights will remain on until the switch is pressed a second time, so be sure they have been turned off before leaving the vehicle.
196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The HomeLink® buttons that are located in the overhead Before You Begin Programming HomeLink® console designate the three different HomeLink® channels. Ensure your vehicle is parked outside of the garage before you begin programming. For efficient programming and accurate transmission of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink® system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197 NOTE: • Erasing all channels should only be performed when programming HomeLink® for the first time. Do not erase channels when programming additional buttons. • If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance. Programming A Rolling Code For programming garage door openers that were manufactured after 1995.
198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink® button you wish to program. attached to the garage door opener/device motor. Firmly press and release the “LEARN” or “TRAINING” button. On some garage door openers/devices there may be a light that blinks when the garage door opener/device is in the LEARN/TRAIN mode. 3.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199 2. Place the hand-held transmitter 1 to 3 inches (3 to 8 cm) away from the HomeLink® button you wish to To reprogram a channel that has been previously trained, program. follow these steps: 3. Simultaneously press and hold both the Homelink® 1. Turn the ignition switch to the ON/RUN position. button you want to program and the hand-held trans2. Press and hold the desired HomeLink® button until mitter button. the EVIC displays “CHANNEL # TRAINING” Do not 4.
200 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 5. Press and hold the programmed HomeLink® button. The EVIC will display “CHANNEL # TRANSMIT”. If the garage door opener/device activates, programming is complete. Canadian/Gate Operator Programming For programming transmitters in Canada/United States that require the transmitter signals to “time-out” after several seconds of transmission.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 201 3. Simultaneously press and hold both the Homelink® Reprogramming A Single HomeLink® Button button while you press and release (“cycle”), your To reprogram a channel that has been previously trained, hand-held transmitter every two seconds. follow these steps: 4. Continue to hold buttons until the EVIC display 1. Turn the ignition switch to the ON/RUN position. changes from “CHANNEL # TRAINING” to “CHAN2.
202 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Security Troubleshooting Tips It is advised to erase all channels before you sell or turn If you are having trouble programming HomeLink®, in your vehicle. here are some of the most common solutions: To erase the channels press and hold the two outside • Replace the battery in the original hand-held transmitter. HomeLink® buttons (I and III) for up 20 seconds.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 203 WARNING! • Your motorized door or gate will open and close while you are programming the universal transceiver. Do not program the transceiver if people, pets or other objects are in the path of the door or gate. Only use this transceiver with a garage door opener that has a “stop and reverse” feature as required by Federal safety standards. This includes most garage door opener models manufactured after 1982.
204 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED The power sunroof switch is located on the overhead console between the courtesy/reading lights. Power Sunroof Switch WARNING! • Never leave children unattended in a vehicle, and do not leave the key in the ignition switch (or leave the ignition of a vehicle equipped with Keyless Enter-N-Go™ in the ACC or ON/Run position).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 205 Opening Sunroof — Express Pinch Protect Feature Press the switch rearward and release it within one-half second and the sunroof will open automatically from any position. The sunroof will open fully and stop automatically. This is called “Express Open”. During Express Open operation, any movement of the sunroof switch will stop the sunroof. This feature will detect an obstruction in the opening of the sunroof during Express Close operation.
206 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Sunshade Operation Sunroof Maintenance The sunshade can be opened manually. However, the Use only a nonabrasive cleaner and a soft cloth to clean sunshade will open automatically as the sunroof opens. the glass panel. NOTE: The sunshade cannot be closed if the sunroof is Ignition Off Operation open.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 207 ELECTRICAL POWER OUTLETS The auxiliary 12 Volt (13 Amp) power outlets can provide power for in-cab accessories designed for use with the standard “cigar lighter” plug. The 12 Volt power outlets have a cap attached to the outlet indicating “12V DC”, together with either a key symbol or a battery symbol. A key symbol indicates that the key must be in the ON/RUN or ACC positions for the outlet to provide power.
208 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The auxiliary power outlets can be found in the following • Center console when equipped with bucket seats.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 209 • Inside the upper lid of the center storage compartment • Rear of the center console storage compartment — — if equipped. Quad Cab® or Crew Cab. 3 Power Outlet — Upper Lid Power Outlet — Rear Center Console The key symbol indicates that this outlet can supply power when the key is in the ON/RUN or ACC positions.
210 UNDERSTANDING THE FEATURES OF YOUR VEHICLE All accessories connected to the outlet(s) should be removed or turned off when the vehicle is not in use to protect the battery against discharge. WARNING! To avoid serious injury or death: • Only devices designed for use in this type of outlet should be inserted into any 12 Volt outlet. • Do not touch with wet hands. • Close the lid when not in use and while driving the vehicle. • If this outlet is mishandled, it may cause an electric shock and failure.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 211 CIGAR LIGHTER AND ASH RECEIVER — IF EQUIPPED A removable ash receiver and cigar lighter are available. For vehicles with a bench seat the cupholder tray can be used to hold the ash receiver.
212 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER INVERTER — IF EQUIPPED A 115 Volt (150 Watts Maximum) outlet is located on the center stack of the instrument panel, to the right of the radio. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts. Certain high-end video games, such as Playstation3 and XBox360 will exceed this power limit, as will most power tools. The power inverter is designed with built-in overload protection.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 213 WARNING! To avoid serious injury or death: • Do not insert any objects into the receptacles. • Do not touch with wet hands. • Close the lid when not in use. • If this outlet is mishandled, it may cause an electric shock and failure. Front Instrument Panel Cupholders — Floor Mounted Shifter For vehicles equipped with bucket seats there are two cupholders located in the floor console.
214 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rear Cupholder — Quad Cab® Rear Cupholder — Crew Cab Quad Cab® vehicles may be equipped with a rear Crew Cab vehicles are equipped with rear cupholders cupholder that consists of two cup wells for rear passen- located in the center armrest. ger convenience.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 215 STORAGE Glove Box Storage The glove box is located on the passenger side of the instrument panel and features both an upper and lower storage area.
216 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To open the upper glove box push upward on the handle To open the lower glove box, pull on the handle to release release. The glove box door will automatically open. the latch and lower the door.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 217 Door Storage Rear Door Storage — Crew Cab Front Door Storage — If Equipped Storage compartments are located in both the driver and passenger door trim panels. Storage areas and bottle holders (drivers side only) are located in the door trim panels.
218 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Center Storage Compartment — If Equipped The center storage compartment is located between the driver and passenger seats. The storage compartment provides an armrest and contains both and upper and lower storage area. Center Storage Compartment WARNING! • This armrest is not a seat. Anyone seated on the armrest could be seriously injured during vehicle operation, or a collision. Only use the center seating position when the armrest is fully upright.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 219 Pull on the upper handle on the front of the armrest to With the upper lid closed, pull on the lower handle to raise the cover. The upper storage area contains a 12 Volt open the lower storage bin. power outlet that can be used to power small electrical devices, refer to “Electrical Power Outlets” for further information.
220 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not operate this vehicle with a console compartment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving. Use of these devices while driving can cause an accident due to distraction, resulting in death or injury. Second Row In-Floor Storage Bin — If Equipped In-floor storage bins are located in front of the second row seats and can be used for extra storage.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 221 To open in-floor storage bin, lift upward on the handle of Seatback Storage the latch and open the lid. Located in the back of both the driver and passenger NOTE: The front seat may have to be moved forward to front seats are pockets that can be used for storage. fully open the lid.
222 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage (Regular Cab) Storage and Seats (Crew Cab) The storage bin is located behind the front seats and runs The Crew Cab models provide additional storage under the length of the cab. the rear seats. Lift the seats to access the storage compartment. To open the storage compartments, lift upward on the handle of the latch and open the lid.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 223 CAUTION! Always lift the storage compartment lids by using the handle. Failure to lift the lids by using the handle can result in damage to the lids. Plastic Grocery Bag Retainers (Regular Cab Models) Retainer hooks which will hold plastic grocery bag handles are built into the back panel of the cab, behind the rear seat.
224 UNDERSTANDING THE FEATURES OF YOUR VEHICLE REAR WINDOW FEATURES Rear Window Defroster The rear window defroster button is located on the climate control panel. Press this button to turn on the rear window defroster and the heated outside mirrors (if equipped). An indicator in the button will illuminate when the rear window defroster is on. The rear window defroster automatically turns off after approximately 10 minutes. For an additional five minutes of operation, press the button a second time.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 225 Power Sliding Rear Window — If Equipped Manual Sliding Rear Window — If Equipped The switch for the power sliding rear window is located A locking device in the center of the window helps to on the overhead console. prevent entry from the rear of the vehicle. Squeeze the lock to release the window. FOLD FLAT LOAD FLOOR — IF EQUIPPED Quad Cab® and Crew Cab models with a 60/40 rear seat may be equipped with a folding load floor.
226 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Unfolding the Load Floor 1. Lift the 60/40 seat cushion(s) to the upward position. Unfolding The Load Floor 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. Load Floor In Open Position 3. Reverse the procedure to store the load floor.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 227 Positioning the Load Floor for Storage Access Under the Seat 1. Lift the 60/40 seat cushion(s) to the upward position. 2. Unsnap the securing snap located at either side of the load floor. 3 3. Lift the load floor up to access storage under the load floor. WARNING! Do not drive with the load floor in the up position. When stopping fast or in an accident, the load floor could move to the down position causing serious injury. Load Floor Securing Straps 4.
228 UNDERSTANDING THE FEATURES OF YOUR VEHICLE PICKUP BOX The pickup box has many features designed for utility and convenience.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 229 NOTE: If you are installing a Toolbox, Ladder Rack or Headache Rack at the front of the Pickup Box, you must use Mopar Box Reinforcement Brackets that are available from your authorized dealer. You can carry wide building materials (sheets of plywood, etc.) by building a raised load floor. Place lumber across the box in the indentations provided above the wheel housings and in the bulkhead dividers to form the floor.
230 UNDERSTANDING THE FEATURES OF YOUR VEHICLE There are stampings in the sheet metal on the inner side bulkheads of the box in front of and behind both wheel housings. Place wooden boards across the box from side to side to create separate load compartments in the pickup box. RamBox® Integrated Box Side Storage Bins Cargo storage bins are located on both sides of the pickup box.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 231 CAUTION! Failure to follow the following items could cause damage to the vehicle: • Assure that all cargo inside the storage bins is properly secured. • Do not exceed cargo weight rating of 150 lb (68 kg) 1500 series vehicles or 300 lbs (136 kg) for 2500 and 3500 series vehicles per bin. To open a storage bin with the RamBox® unlocked, press and release the button located on the lid. The RamBox® lid will open upward to allow hand access.
232 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! (Continued) it is recommended that the bin lights be turned off manually using the on/off switch. Cargo bins feature two removable drain plugs (to allow water to drain from bins). To remove plug, pull up on the edge. To install push plug downward into drain hole. NOTE: Provisions are provided in the bins for cargo dividers and shelf supports. These accessories (in addition to other RamBox® accessories) are available from MOPAR®.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 233 the storage bin, insert the key into the keyhole on the RamBox® Safety Warning pushbutton and turn clockwise to lock or counterclock- Carefully follow these warnings to help prevent personal wise to unlock. Always return the key to the upright injury or damage to your vehicle: (vertical) position before removing the key from the pushbutton. WARNING! CAUTION! • Ensure cargo bin lids are closed and latched before moving or driving vehicle.
234 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: In the event of an individual being locked inside the storage bin, the storage bin cover can be opened from As a security measure, a Storage Bin Cover Emergency inside of the bin by pulling on the glow-in-the-dark lever Release is built into the storage bin cover latching mecha- attached to the storage bin cover latching mechanism. nism.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 235 1. Make sure the center handle is unlocked using the 2. With the side gates open, position the extender fully vehicle key and rotate the center handle vertically to forward in the bed against the front panel. release the extender side gates.
236 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Rotate the side gates closed allowing the outboard ends to be positioned in front of the cargo tie down loops. Side Gates Closed 5. Lock the center handle using the vehicle key to secure the panel into place and assist against theft. Cargo Tie Down Loop 4. Rotate the center handle horizontally to secure the side gates in the closed position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 237 Divider Position The divider position is intended for managing your cargo and assisting in keeping cargo from moving around the bed. There are 11 divider slots along the bed inner panels which allow for various positions to assist in managing your cargo. 3 To install the bed extender into a divider position perform the following: 1.
238 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. With the side gates open, position the extender so the 4. Rotate the center handle horizontally to secure the side outboard ends align with the intended slots in the gates in the closed position. sides of the bed. Side Gates Closed Aligning Gate To Slots 3. Rotate the side gates closed so that the outboard ends are secured into the intended slots of the bed. 5. Lock the center handle to secure the panel into place and assist against theft.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 239 Extender Position The extender position allows you to load the bed of the truck beyond the tail gate. The bed extender will add an additional 15 in (38 cm) in the back of the truck when additional cargo room is needed. The extender position utilizes a locating pin and rotating handle located on both sides of the truck bed near the tailgate. 3 Extender Position To install the bed extender into the extender position perform the following: 1.
240 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Make sure the center handle is unlocked and rotate the 4. Rotate the handles to the horizontal position to secure center handle vertically in order to release the exinto place. tender side gates. 3. Fit the end of the side gate ends onto the pin and handle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 241 WARNING! To reduce the risk of potential injury or property damage: • Cargo must be secured. • Do not exceed cargo load rating of your vehicle. • Secure all loads to truck utilizing cargo tie downs. • Extender should not be used as cargo tie down. • When vehicle is in motion do not exceed 150 lbs (68 kg) load on the tailgate. • The bed extender is not intended for off road use.
242 UNDERSTANDING THE FEATURES OF YOUR VEHICLE out on the cleat and slide it to the detent nearest the desired location. Make sure the cleat is seated in the detent and tighten the nut. Adjustable Cleats Each cleat must be located and tightened down in one of the detents, along either rail, in order to keep cargo properly secure. 1 — Utility Rail Detent To move the cleat to any position on the rail, turn the nut 2 — Cleat Retainer Nut 3 — Utility Rail Cleat counterclockwise, approximately three turns.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 243 To remove the cleats from the utility rail, remove the end SLIDE-IN CAMPERS cap by pushing up on the locking tab, located on the Camper Applications bottom of the end cap. Slide the cleat off the end of the Certain truck models are not recommended for slide-in rail. campers. To determine if your vehicle is excluded, please refer to the “Consumer Information Truck-Camper Loading” document available from your authorized dealer.
244 UNDERSTANDING THE FEATURES OF YOUR VEHICLE EASY-OFF TAILGATE Disconnecting the Rear Camera or Remote To simplify mounting of a camper unit with an overhang, Keyless Entry — If Equipped the tailgate can be removed. 1. Open the tailgate to access the rear camera or RKE connector bracket located on the rear sill. NOTE: If your vehicle is equipped with a rear camera or RKE the electrical connector must be disconnected prior to removing the tailgate.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 245 2. Remove the connector bracket from the sill by press- 4. Connect the chassis plug and bracket (provided in the ing inward in the locking tab. glove box) to the chassis wiring harness and insert the bracket back into the sill. 5. Connect the tailgate plug (provided in the glove box) to the tailgate wiring harness to ensure that the terminals do not corrode. 6. Tape the tailgate harness and bracket against the forward-facing surface of the tailgate.
246 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Make sure tailgate is supported when removing 5. Slide the entire tailgate to the right to free the left side support cables. pivot. 6. Remove the tailgate from the vehicle. NOTE: Do not carry the tailgate loose in the truck pickup box. WARNING! To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the overhanging camper compartment and be free of leaks.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 247 TRI-FOLD TONNEAU COVER-IF EQUIPPED Tri-Fold Tonneau Cover Removal Tri-Fold Tonneau Cover — If Equipped To remove the Tonneau Cover follow the following steps: Your vehicle may be equipped with a Tri-Fold Tonneau 1. Lower the tailgate. Cover which consists of different features: 2. Pull down on the clamp on both driver and passenger • Easy Tri-Fold cover sides. • Tonneau fore aft locator • Crosscar inside bed locator 3.
248 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Clamped Position NOTE: If clamp wire is damaged replace immediately.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 249 3 Released Position Stowage Strap NOTE: Be sure the Tonneau Cover has been folded completely before removing.
250 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Tri-Fold Tonneau Cover Installation And Cleaning Position the folded Tonneau Cover on the truck bed and push the Cover forward against the front of the truck bed. The Tonneau Cover centers itself when placed on the vehicle. Disengage the stowage straps and unfold the Tonneau Cover then attach the rear clamps to the truck bed flange to secure the Tonneau Cover to the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS 䡵 INSTRUMENT PANEL FEATURES . . . . . . . . . .253 ▫ EVIC White Telltales . . . . . . . . . . . . . . . . . . .277 䡵 INSTRUMENT CLUSTER — PREMIUM . . . . . . .254 ▫ EVIC Red Telltales . . . . . . . . . . . . . . . . . . . . .277 䡵 INSTRUMENT CLUSTER DESCRIPTIONS . . . . .255 ▫ EVIC Green Telltales . . . . . . . . . . . . . . . . . . .279 䡵 ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) . . . . . . . . . . . . . . . . . . . . . . . .
252 UNDERSTANDING YOUR INSTRUMENT PANEL 䡵 iPod®/USB/MP3 CONTROL — IF EQUIPPED. . . . . . . . . . . . . . . . . . . . . . . . . .310 ▫ Manual Climate Controls With Touch-Screen — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .319 䡵 STEERING WHEEL AUDIO CONTROLS — IF EQUIPPED . . . . . . . . . . . . . . . . . . . . . . . . .311 ▫ Automatic Climate Controls With Touch-Screen — If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .324 ▫ Radio Operation . . . . . . . . . . . . . . . . .
UNDERSTANDING YOUR INSTRUMENT PANEL 253 INSTRUMENT PANEL FEATURES 4 1 — Headlight Switch 2 — Instrument Cluster 3 — Radio 4 — Hazard Switch 5 — Upper Glove Compartment 6 — Lower Glove Compartment 7 — 115v Power Inverter Outlet 8 — Power Outlet 9 — Lower Switch Bank (Engine Start/Stop, ESC OFF, TOW/HAUL, Electronic Trailer Brake, Air Suspension, Park Assist) — If Equipped 10 — Instrument Panel Drawer 11 — Climate Controls 12 — Power Outlet/Cigar Lighter 13 — Gear Selector/Transfer Case Position Switch
254 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER — PREMIUM
UNDERSTANDING YOUR INSTRUMENT PANEL 255 If the ABS light remains on or turns on while driving, it indicates that the anti-lock portion of the brake system is 1. Tachometer not functioning and that service is required. However, The tachometer indicates engine speed in Revolutions the conventional brake system will continue to operate Per Minute (RPM x 1000). normally if the BRAKE warning light is not on.
256 UNDERSTANDING YOUR INSTRUMENT PANEL testing the light will come on when the ignition is first turned on and remain on for 15 seconds, then blink for 5 seconds, and remain on until the vehicle is started. If the bulb does not come on during starting, have the condition investigated promptly. If this light comes on and remains on while driving, it suggests a potential engine control problem and the need for system service.
UNDERSTANDING YOUR INSTRUMENT PANEL 257 NOTE: The voltmeter may show a gauge fluctuation at • A continuous chime will sound if the vehicle is various engine temperatures. This cycling operation is driven more than 1 mile (1.6 km) with either turn caused by the post-heat cycle of the intake manifold heater system. The number of cycles and the length of the signal on. cycling operation is controlled by the engine control • Check for an inoperative outside light bulb if either module.
258 UNDERSTANDING YOUR INSTRUMENT PANEL hydraulic system malfunction or that a problem with the If brake failure is indicated, immediate repair is necesBrake Booster has been detected by the Anti-Lock Brake sary. System (ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the condition WARNING! has been corrected.
UNDERSTANDING YOUR INSTRUMENT PANEL 259 unless the parking brake is applied or a brake fault is 8. Seat Belt Reminder Light detected. If the light does not illuminate, have the light When the ignition switch is first turned to inspected by an authorized dealer. ON/RUN, this light will turn on for four to The light also will turn on when the parking brake is eight seconds as a bulb check.
260 UNDERSTANDING YOUR INSTRUMENT PANEL dealer as soon as possible. Refer to “Occupant Restraints” 13. Cargo Light — If Equipped in “Things To Know Before Starting Your Vehicle” for The cargo light will illuminate when the cargo further information. light is activated by pressing the cargo light 10. Oil Pressure Gauge — If Equipped button on the headlight switch. The pointer should always indicate some oil pressure when the engine is running.
UNDERSTANDING YOUR INSTRUMENT PANEL 261 by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.
262 UNDERSTANDING YOUR INSTRUMENT PANEL replacement or alternate tires and wheels allow the TPMS 17. Front Fog Light Indicator — If Equipped to continue to function properly. This indicator will illuminate when the front fog lights are on. CAUTION! The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 263 NOTE: The highest available transmission gear is dis- 22. TOW/HAUL played in the lower right corner of the Electronic Vehicle The TOW HAUL button is located on the center Information Center (EVIC) whenever the Electronic stack upper switch bank. This light will illumiRange Select (ERS) feature is active. Use the +/- selector nate when TOW HAUL mode is selected. on the shift lever to activate ERS.
264 UNDERSTANDING YOUR INSTRUMENT PANEL The gauge pointer will likely indicate a higher tempera• The “ESC Off Indicator Light” and the “ESC ture when driving in hot weather, up mountain grades, Activation/Malfunction Indicator Light” come on or when towing a trailer. It should not be allowed to momentarily each time the ignition switch is turned exceed the upper limits of the normal operating range. to ON/RUN.
UNDERSTANDING YOUR INSTRUMENT PANEL 265 WARNING! ELECTRONIC VEHICLE INFORMATION CENTER (EVIC) A hot engine cooling system is dangerous. You or others could be badly burned by steam or boiling coolant. You may want to call an authorized dealer for service if your vehicle overheats. If you decide to look under the hood yourself, see “Maintaining Your Vehicle.” Follow the warnings under the “Cooling System Pressure Cap” paragraph.
266 UNDERSTANDING YOUR INSTRUMENT PANEL This system allows the driver to select a variety of useful • Vehicle Settings (Not Equipped with a Uconnect® information by pressing the switches mounted on the Access 5.0 & 8.4 radio) steering wheel.
UNDERSTANDING YOUR INSTRUMENT PANEL 267 • UP Arrow Button Press and release the UP arrow button to scroll upward through the main menu and submenus (Fuel Economy, Trip A, Trip B, Audio, Stored Messages, Screen Set Up). • DOWN Arrow Button • SELECT/RIGHT Arrow Button Press and release the SELECT/RIGHT arrow button to access/select the information screens or sub-menu screens of a main menu item.
268 UNDERSTANDING YOUR INSTRUMENT PANEL Electronic Vehicle Information Center (EVIC) Displays 1. Main Screen — The inner ring of the display will illuminate in grey under normal conditions, yellow for non critical warnings, red for critical warnings and white for on demand information. 2. Audio / Phone Information and Sub-menu Information — Whenever there are sub-menus available, the position within the sub-menus is shown here. 3.
UNDERSTANDING YOUR INSTRUMENT PANEL 269 The main display area will normally display the main menu or the screens of a selected feature of the main menu. The main display area also displays “pop up” messages that consist of approximately 60 possible warning or information messages.
270 UNDERSTANDING YOUR INSTRUMENT PANEL Engine Oil Change Indicator System Vehicles Equipped With Keyless Enter-N-Go™ Oil Change Required 1. Without pressing the brake pedal, press the ENGINE START/STOP button and cycle the ignition to the Your vehicle is equipped with an engine oil change ON/ RUN position (Do not start the engine.) indicator system. The “Oil Change Required” message will flash in the EVIC display for approximately 10 2.
UNDERSTANDING YOUR INSTRUMENT PANEL 271 NOTE: If the indicator message illuminates when you • Service Antilock Brake System start the vehicle, the oil change indicator system did not • Service Electronic Throttle Control reset. If necessary, repeat this procedure.
272 UNDERSTANDING YOUR INSTRUMENT PANEL • Service Electronic Throttle Control • Remote Start Aborted Hood Open • Lights On • Remote Start Aborted Trunk Open • Right Turn Signal Light Out • Remote Start Aborted Time Expired • Left Turn Signal Light Out • Remote Start Disabled Start to Reset • Turn Signal On • Service Airbag System • Vehicle Not in Park • Service Airbag Warning Light • Key in Ignition • Driver Seatbelt Unbuckled • Key in Ignition Lights On • Passenger Seatbelt Unbuckled • Rem
UNDERSTANDING YOUR INSTRUMENT PANEL 273 • Shift to Neutral then Drive or Reverse • Normal Ride Height Achieved • Autostick Unavailable Service Required • Aerodynamic Ride Height Achieved • Automatic Unavailable Use Autostick Service Req. • Off Road 1 Ride Height Achieved • Transmission Getting Hot Press Brake • Off Road 2 Ride Height Achieved • Trans.
274 UNDERSTANDING YOUR INSTRUMENT PANEL • Battery Low Start Engine To Change Ride Height • Stop/Start Ready – If Equipped • Stop/Start Not Ready – If Equipped • Stop/Start Not Ready Hood Open – If Equipped • Stop/Start Not Ready Battery Charging – If Equipped • Stop/Start Not Ready Trailer Tow/Haul Selected – If Equipped • Stop/Start Not Ready 4WD/Low Range Selected – If Equipped • Stop/Start Not Ready Fuel Level Low – If Equipped • Stop/Start Not Ready Steep Incline – If Equipped • Stop/Start Not Ready E
UNDERSTANDING YOUR INSTRUMENT PANEL 275 • Stop/Start Not Ready Steering Wheel Turned – If Equipped • Stop/Start Autostop Active – If Equipped The Reconfigurable Telltales section is divided into the white telltales area on the right, amber telltales in the middle, and red telltales on the left. EVIC Amber Telltales • Stop/Start To Restart Press Clutch Or Shift To Neutral This area will show reconfigurable amber caution tell– If Equipped tales.
276 UNDERSTANDING YOUR INSTRUMENT PANEL • Low Coolant Level Indicator Protection Mode will automatically be selected in order to “protect” the air suspension system, air suspension This telltale will turn on to indicate the vehicle adjustment is limited due to payload. coolant level is low. • Service Stop/Start System Telltale - If Equipped • Transmission Temperature Warning Telltale This telltale indicates that the transmission fluid temperature is running hot.
UNDERSTANDING YOUR INSTRUMENT PANEL 277 WARNING! If you continue operating the vehicle when the Transmission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. EVIC White Telltales • Electronic Speed Control Ready EVIC Red Telltales This area will show reconfigurable red telltales. These telltales include: • Door Ajar This light will turn on to indicate that one or more doors may be ajar.
278 UNDERSTANDING YOUR INSTRUMENT PANEL • Oil Temperature Warning Light This telltale indicates engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. • Charging System Light This light shows the status of the electrical charging system. If the light stays on or comes on while driving, turn off some of the vehicle’s non-essential electrical devices or increase engine speed (if at idle).
UNDERSTANDING YOUR INSTRUMENT PANEL 279 • Engine Temperature Warning Light EVIC Green Telltales This light warns of an overheated engine condi- • Electronic Speed Control SET tion. As temperatures rise and the gauge apThis telltale will illuminate green when the proaches H, this indicator will illuminate and a single electronic speed control is SET. For further chime will sound after reaching a set threshold.
280 UNDERSTANDING YOUR INSTRUMENT PANEL Press and release the UP or DOWN arrow button until “Tire Pressure” is highlighted in the EVIC. Press and Press and release the UP or DOWN arrow release the SELECT/RIGHT arrow button and one of the button until the Vehicle Info icon is highlighted following will be displayed: in the EVIC.
UNDERSTANDING YOUR INSTRUMENT PANEL 281 Refer to “Tire Pressure Monitoring System (TPMS)” Trip B under “Starting and Operating” for further information. Press and release the Left or Right arrow button until the Trip B icon is highlighted in the EVIC (Toggle left or right to select Trip A or Press and release the UP or DOWN arrow Trip B). The Trip B information will display the button until the Trip A icon is highlighted in following: the EVIC (Toggle left or right to select Trip A or Trip B).
282 UNDERSTANDING YOUR INSTRUMENT PANEL Fuel Economy Trailer Tow Press and release the UP or DOWN arrow button until the Fuel Economy icon is highlighted. Press and release the UP or DOWN arrow button until the Trailer Tow icon is highlighted.
UNDERSTANDING YOUR INSTRUMENT PANEL 283 Screen Setup Personal Settings (Customer-Programmable Press and release the UP or DOWN arrow Features) button until the Screen Setup display icon is For vehicles equipped a 3.5” EVIC screen highlighted in the EVIC. Press and release the Personal Settings allows the driver to set and recall SELECT/RIGHT arrow button to enter the features when the transmission is in PARK. Screen Setup sub-menu.
284 UNDERSTANDING YOUR INSTRUMENT PANEL Press and release the SELECT/RIGHT arrow button to Units Enter Vehicle Settings Press and release the UP or DOWN button until “Units” Use the UP or DOWN button to display one of the displays in the EVIC and press the SELECT button. The EVIC, odometer, and navigation system (if equipped) can following choices. be changed between English and Metric units of meaNOTE: Your vehicle may or may not be equipped with sure.
UNDERSTANDING YOUR INSTRUMENT PANEL 285 button until a check-mark appears next to the feature showing the system has been activated or the check-mark The Rear Park Assist system will scan for objects behind is removed showing the system has been deactivated. the vehicle when the transmission is in the REVERSE position and the vehicle speed is less than 11 mph Auto Wipers — If Equipped (18 km/h).
286 UNDERSTANDING YOUR INSTRUMENT PANEL feature showing the system has been activated or the highlighted, then press and release the SELECT button check-mark is removed showing the system has been until a check-mark appears next to the setting, showing that the setting has been selected. deactivated. Headlamp Off Delay Headlamps With Wipers When this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL 287 showing the system has been activated or the check-mark is removed showing the system has been deactivated. Refer to “Lights/SmartBeam™ — If Equipped” in “Understanding The Features Of Your Vehicle” for further information. Flash Lamps With Lock When this feature is selected, the front and rear turn signals will flash when the doors are locked or unlocked with the RKE transmitter. This feature may be selected with or without the sound horn on lock feature selected.
288 UNDERSTANDING YOUR INSTRUMENT PANEL feature showing the system has been activated or the When Unlock All Doors On 1st Press is selected, all of check-mark is removed showing the system has been the doors will unlock on the first press of the RKE transmitter UNLOCK button. To make your selection, deactivated.
UNDERSTANDING YOUR INSTRUMENT PANEL 289 a check-mark appears next to the feature showing the system has been activated or the check-mark is removed This feature allows you to lock and unlock the vehicle’s showing the system has been deactivated. door(s) without having to press the RKE transmitter lock or unlock buttons.
290 UNDERSTANDING YOUR INSTRUMENT PANEL selection, scroll up or down until the preferred setting is highlighted, then press and release the SELECT button until a check-mark appears next to the setting, showing that the setting has been selected. Transport Mode – If Equipped Tire/Jack Mode – If Equipped Horn with Remote Lower – If Equipped When this feature is selected the air suspension system is disabled to assist with flat bed towing.
UNDERSTANDING YOUR INSTRUMENT PANEL 291 the feature showing the system has been activated or the release the SELECT button until a check-mark appears check-mark is removed showing the system has been next to the setting, showing that the setting has been selected. deactivated. Lights with Remote Lower – If Equipped Trailer Brake Type When this feature is selected, the front and rear turn signals will flash when the RKE transmitter REMOTE LOWER button is pressed.
292 UNDERSTANDING YOUR INSTRUMENT PANEL press and release the SELECT button until a check-mark • Outside Temp (default setting) appears next to the setting, showing that the setting has • Trans Temp been selected. • Oil Temp Calibrate Compass • Time Refer to “Compass Display” for more information. • Range To Empty (RTE) Compass Variance • Average MPG Refer to “Compass Display” for more information. Screen Setup Driver Selectable Items • Current MPG Odometer • Trip A • 000 • Trip B • 000.
UNDERSTANDING YOUR INSTRUMENT PANEL 293 • Compass (default setting) Lower Left • Outside Temp • None (default setting) • Trans Temp • Compass • Oil Temp • Outside Temp • Time • Trans Temp • Range To Empty (RTE) • Oil Temp • Average MPG • Time • Current MPG • Range • Trip A • AVG MPG • Trip B • Current MPG • Trailer Trip (distance only) • Trailer Brake Gain • Trailer Brake Gain Lower Right • None (default setting) 4
294 UNDERSTANDING YOUR INSTRUMENT PANEL • Compass Uconnect® SETTINGS • Outside Temp • Oil Temp The Uconnect® system uses a combination of soft and hard keys located on the center of the instrument panel that allows you to access and change the customer programmable features. • Time Hard-Keys • Trans Temp • Range Hard-Keys are located below the Uconnect® system in the center of the instrument panel.
UNDERSTANDING YOUR INSTRUMENT PANEL 295 Press the Screen Off hard-key to turn off the Uconnect® When making a selection, press the soft-key to enter the screen. Press the Screen Off hard-key a second time to desired mode. Once in the desired mode press and turn the screen on. release the preferred setting until a check-mark appears next to the setting, showing that setting has been sePress the Back hard-key to exit out of a Menu or certain lected.
296 UNDERSTANDING YOUR INSTRUMENT PANEL • Display Brightness With Headlights ON language soft-key until a check-mark appears next to the language, showing that setting has been selected. Touch When in this display, you may select the brightness with the back arrow soft-key to return to the previous menu. the headlights on. Adjust the brightness with the + and – setting soft-keys or by selecting any point on the scale • Units between the + and – soft-keys.
UNDERSTANDING YOUR INSTRUMENT PANEL 297 • Touchscreen Beep • Fuel Saver Display In Cluster When in this display, you may turn on or shut off the sound heard when a touch screen button (soft-key) is pressed. Touch the Touchscreen Beep soft-key until a check-mark appears next to the setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu. The “ECO” message is located in the instrument cluster display, this message can be turned on or off.
298 UNDERSTANDING YOUR INSTRUMENT PANEL • Set Time Hours check-mark appears next to the 12hrs or 24hrs setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu. When in this display, you may adjust the hours. The Sync with GPS Time soft-key must be unchecked. To make your selection touch the + or - soft-keys to adjust the Safety / Assistance hours up or down.
UNDERSTANDING YOUR INSTRUMENT PANEL 299 • Tilt Mirrors In Reverse When this feature is selected, the outside sideview mirrors will tilt downward when the ignition is in the RUN position and the transmission shift lever is in the REVERSE position. The mirrors will move back to their previous position when the transmission is shifted out of REVERSE. To make your selection, touch the Tilt Mirrors In Reverse soft-key, until a check-mark appears next to setting, showing that setting has been selected.
300 UNDERSTANDING YOUR INSTRUMENT PANEL the Hill Start Assist soft-key, until a check-mark appears • Headlight Illumination On Approach next to setting, showing that setting has been selected. When this feature is selected, the headlights will activate Touch the back arrow soft-key to return to the previous and remain on for 0, 30, 60, or 90 seconds when the doors menu. are unlocked with the Remote Keyless Entry (RKE) • Four Corner Air Suspension Modes — If Equipped transmitter.
UNDERSTANDING YOUR INSTRUMENT PANEL 301 • Auto Dim High Beams “SmartBeam™” — If Equipped • Flash Headlights With Lock When this feature is selected, the high beam headlights will deactivate automatically under certain conditions. To make your selection, touch the Auto High Beams softkey, until a check-mark appears next to setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu.
302 UNDERSTANDING YOUR INSTRUMENT PANEL • Auto Unlock On Exit • Sound Horn With Remote Start When this feature is selected, all doors will unlock when the vehicle is stopped and the transmission is in the PARK or NEUTRAL position and the driver’s door is opened. To make your selection, touch the Auto Unlock On Exit soft-key, until a check-mark appears next to setting, showing that setting has been selected. Touch the back arrow soft-key to return to the previous menu.
UNDERSTANDING YOUR INSTRUMENT PANEL 303 NOTE: If the vehicle is programmed 1st Press Of Key Fob Unlocks, all doors will unlock no matter which Passive Entry equipped door handle is grasped. If 1st Press Of Key Fob Unlocks is programmed, only the driver’s door will unlock when the driver’s door is grasped. With Passive Entry, if 1st Press Of Key Fob Unlocks is programmed touching the handle more than once will only result in the driver’s door opening.
304 UNDERSTANDING YOUR INSTRUMENT PANEL Seats soft-key, until a check-mark appears next to setting, showing that setting has been selected. Touch the back After pressing the Auto-On Comfort & Remote Start arrow soft-key to return to the previous menu. soft-key the following settings will be available. Engine Off Options • Horn With Remote Start Auto-On Comfort & Remote Start When this feature is selected, the horn will sound when the remote start is activated.
UNDERSTANDING YOUR INSTRUMENT PANEL 305 • Headlight Off Delay • Variance When this feature is selected, the driver can choose to have the headlights remain on for 0, 30, 60, or 90 seconds when exiting the vehicle. To change the Headlight Off Delay status touch the + or - soft-key to select your desired time interval. Touch the back arrow soft-key to return to the previous menu. Compass Variance is the difference between Magnetic North and Geographic North.
306 UNDERSTANDING YOUR INSTRUMENT PANEL calibrate the compass by pressing the ON soft-key and completing one or more 360-degree turns (in an area free from large metal or metallic objects) until the CAL indicator displayed in the EVIC turns off. The compass will now function normally. Audio After pressing the Audio soft-key the following settings will be available. • Balance/Fade Compass Variance Map When in this display you may adjust the Balance and Fade settings.
UNDERSTANDING YOUR INSTRUMENT PANEL 307 NOTE: Bass/Mid/Treble allow you to simply slide your To make your selection, touch the AUX Volume Match finger up or down to change the setting as well as touch soft-key, select On or Off followed by pressing the arrow back soft-key. directly on the desired setting. • Speed Adjusted Volume • Loudness — If Equipped This feature increases or decreases volume relative to vehicle speed. To change the Speed Adjusted Volume touch the Off, 1, 2 or 3 soft-key.
308 UNDERSTANDING YOUR INSTRUMENT PANEL Air Suspension – If Equipped system has been activated or the check-mark is removed showing the system has been deactivated. After pressing the Suspension soft-key the following • Suspension Display Messages settings will be available. • Sound Horn with Remote Lower When All is selected, all the Air Suspension Alerts will be When this feature is selected, a short horn sound will displayed.
UNDERSTANDING YOUR INSTRUMENT PANEL 309 to the feature showing the system has been activated or • Channel Skip the check-mark is removed showing the system has been SiriusXM can be programmed to designate a group of deactivated. channels that are the most desirable to listen to or to • Transport Mode exclude undesirable channels while scanning.
310 UNDERSTANDING YOUR INSTRUMENT PANEL Write down the SIRIUS ID numbers for your receiver. To iPod®/USB/MP3 CONTROL — IF EQUIPPED reactivate your service, either call the number listed on Located inside the center console upper lid, this feature the screen or visit the provider online. allows an iPod® or external USB device to be plugged NOTE: SiriusXM Travel Link is a separate subscription into the USB port. and is available for U.S. residents only.
UNDERSTANDING YOUR INSTRUMENT PANEL 311 The right hand control is a rocker type switch with a pushbutton in the center. Pressing the top of the switch The remote sound system controls are located on the back will increase the volume, and pressing the bottom of the surface of the steering wheel. Reach behind the wheel to switch will decrease the volume. access the switches. The button located in the center of the right hand control will switch modes to Radio, CD or other valid audio source.
312 UNDERSTANDING YOUR INSTRUMENT PANEL The button located in the center of the left hand control 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. will tune to the next pre-set station that you have programmed in the radio pre-set pushbuttons. 3. Do not apply paper or tape to the disc; avoid scratching the disc. CD Player Pressing the top of the switch once will go to the next 4. Do not use solvents such as benzene, thinner, cleaners, track on the CD.
UNDERSTANDING YOUR INSTRUMENT PANEL 313 RADIO OPERATION AND MOBILE PHONES CLIMATE CONTROLS Under certain conditions, the mobile phone being on in your vehicle can cause erratic or noisy performance from your radio. This condition may be lessened or eliminated by relocating the mobile phone antenna. This condition is not harmful to the radio.
314 UNDERSTANDING YOUR INSTRUMENT PANEL Front Blower Control There are four blower speeds. Use this control to regulate the amount of air forced through the system in any mode you select. The blower speed increases as you move the control clockwise from the OFF position. NOTE: For vehicles equipped with Remote Start, the climate controls will not function during Remote Start operation if the blower control is left in the OFF position.
UNDERSTANDING YOUR INSTRUMENT PANEL 315 Temperature Control Use this control to regulate the temperature of the air inside the passenger compartment. Rotating the knob counterclockwise, from top center into the blue area of the scale, indicates cooler temperatures. Rotating the knob clockwise, into the red area, indicates warmer temperatures. MAX A/C For maximum cooling, when MAX A/C is selected the A/C is turned on automatically and the air is recirculated.
316 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Control (Air Direction) Mode control allows you to choose from several patterns of air distribution. You can select either a primary mode, as identified by the symbols, or a blend of two of these modes. The closer the control is to a particular mode, the more air distribution you receive from that mode. Bi-Level Mode Air is directed through the panel and floor outlets.
UNDERSTANDING YOUR INSTRUMENT PANEL 317 Mix Mode Recirculation Control Air is directed through the floor, defrost and side Press this button to choose between outside air window demist outlets. This setting works best in intake or recirculation of the air inside the cold or snowy conditions that require extra heat at the vehicle. A LED will illuminate when you are in windshield. This setting is good for maintaining comfort, Recirculation mode.
318 UNDERSTANDING YOUR INSTRUMENT PANEL • In cold or damp weather, the use of the Recirculation mode will cause windows to fog on the inside because of moisture buildup inside the vehicle. For maximum defogging, select the outside air position. Economy Mode If ECONOMY mode is desired, press the A/C button to turn off the LED indicator and the A/C compressor. Rotate the temperature control knob to the desired tem• The A/C can be deselected manually without disturb- perature.
UNDERSTANDING YOUR INSTRUMENT PANEL 319 Manual Climate Controls With Touch-Screen — If Equipped Soft-Keys Soft-keys are accessible on the radio touch-screen. Hard-Keys The hard-keys are located below the radio touch-screen.
320 UNDERSTANDING YOUR INSTRUMENT PANEL Button Descriptions (Applies To Both Hard-keys And increase when Defrost mode is selected. If the front Soft-keys) defrost mode is turned off the climate system will return the previous setting. 1. A/C Button 4. Defrost Button Press and release to change the current setting, the indicator illuminates when A/C is ON.
UNDERSTANDING YOUR INSTRUMENT PANEL 321 CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window.
322 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: BI-LEVEL mode is designed under comfort conditions to provide cooler air out of the panel outlets and warmer air from the floor outlets. • Floor Mode Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. • Mix Mode Air comes from the floor, defrost and side window demister outlets. This mode works best in cold or snowy conditions.
UNDERSTANDING YOUR INSTRUMENT PANEL 323 7. Climate Control OFF Button Recirculation Control Press and release this button to turn the Climate Control ON/OFF. When outside air contains smoke, odors, or high humidity, or if rapid cooling is desired, 8. Temperature Control Down Button you may wish to recirculate interior air by pressing the RECIRCULATION control button. Push the button for cooler temperature settings.
324 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Climate Controls With Touch-Screen — If Equipped Soft-Keys Soft-keys are accessible on the radio touch-screen. Hard-Keys The hard-keys located below the radio touch-screen.
UNDERSTANDING YOUR INSTRUMENT PANEL 325 Button Descriptions (Applies To Both Hard-keys And increase when Defrost mode is selected. If the front Soft-keys) defrost mode is turned off the climate system will return the previous setting. 1. A/C Button 4. Defrost Press and release to change the current setting, the indicator illuminates when A/C is ON.
326 UNDERSTANDING YOUR INSTRUMENT PANEL CAUTION! Failure to follow these cautions can cause damage to the heating elements: • Use care when washing the inside of the rear window. Do not use abrasive window cleaners on the interior surface of the window. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Labels can be peeled off after soaking with warm water. • Do not use scrapers, sharp instruments, or abrasive window cleaners on the interior surface of the window.
UNDERSTANDING YOUR INSTRUMENT PANEL 327 NOTE: BI-LEVEL mode is designed under comfort conditions to provide cooler air out of the panel outlets and warmer air from the floor outlets. • Floor Mode Air comes from the floor outlets. A slight amount of air is directed through the defrost and side window demister outlets. • Mix Mode Air comes from the floor, defrost and side window demister outlets. This mode works best in cold or snowy conditions. Hard-key 6.
328 UNDERSTANDING YOUR INSTRUMENT PANEL the red arrow soft-key for warmer temperature settings 11. SYNC or slide the temperature bar towards the blue arrow Press the Sync soft-key to toggle the Sync feature On/Off. soft-key for cooler temperature settings. The Sync indicator is illuminated when this feature is 9. Passenger Temperature Controls enabled. Sync is used to synchronize the passenger temperature setting with the driver temperature setting. Push the Up button for warmer temperature settings.
UNDERSTANDING YOUR INSTRUMENT PANEL 329 3. When the system is set up for your comfort level, it is Recirculation Control not necessary to change the settings. You will experience the greatest efficiency by simply allowing the When outside air contains smoke, odors, or system to function automatically. high humidity, or if rapid cooling is desired, you may wish to recirculate interior air by NOTE: pressing the RECIRCULATION control button.
330 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: In cold weather, use of Recirculation mode may lead to excessive window fogging. The recirculation feature may be unavailable (soft-key button greyed out) if conditions exist that could create fogging on the inside of the windshield. On systems with Manual Climate Controls, the recirculation mode is not allowed in Defrost mode to improve window clearing operation. Recirculation will be disabled automatically if this mode is selected.
UNDERSTANDING YOUR INSTRUMENT PANEL 331 Window Fogging and Frosting Outside Air Intake Vehicle windows tend to fog on the inside of the glass in mild, rainy and/or humid weather. Windows may frost on the inside of the glass in very cold weather. To clear the windows, select Defrost or Mix mode and increase the front blower speed. Do not use the Recirculation mode without A/C for long periods, as fogging may occur.
332 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Chart
STARTING AND OPERATING CONTENTS 䡵 STARTING PROCEDURES . . . . . . . . . . . . . . . .340 䡵 STOP/START SYSTEM — IF EQUIPPED . . . . . .344 ▫ Normal Starting. . . . . . . . . . . . . . . . . . . . . . .340 ▫ Automatic Mode . . . . . . . . . . . . . . . . . . . . . .344 ▫ Automatic Transmission . . . . . . . . . . . . . . . .340 ▫ Possible Reasons The Engine Does Not AUTO STOP . . . . . . . . . . . . . . . . . . . . . . . . .345 ▫ Keyless Enter-N-Go™ . . . . . . . . . . . . . . . . . .
334 STARTING AND OPERATING 䡵 AUTOMATIC TRANSMISSION . . . . . . . . . . . .350 ▫ Key Ignition Park Interlock. . . . . . . . . . . . . . .352 ▫ Brake/Transmission Shift Interlock System . . .352 ▫ Eight-Speed Automatic Transmission – If Equipped . . . . . . . . . . . . . . . . . . . . . . . . .352 ▫ Six–Speed Automatic Transmission If Equipped — 1500 Models Only . . . . . . . . . . . . . . . . . . . . .361 ▫ Electronically Shifted Transfer Case (Five-Position Switch) – If Equipped . . . . . . . .
STARTING AND OPERATING 335 䡵 SAFE OFF-ROAD DRIVING — POWER WAGON ONLY . . . . . . . . . . . . . . . . .418 ▫ Acceleration . . . . . . . . . . . . . . . . . . . . . . . . .437 ▫ Traction . . . . . . . . . . . . . . . ▫ Off-Road Driving Tips And Vehicle 䡵 DRIVING THROUGH WATER Characteristics . . . . . . . . . . . . . . . . . . . . . . .418 ▫ Flowing/Rising Water . . . . . ▫ Driving In Snow, Mud And Sand . . . . . . . . . .421 ▫ Shallow Standing Water . . . .
336 STARTING AND OPERATING ▫ Rigging Techniques . . . . . . . . . . . . . . . . . . . .460 ▫ Brake Assist System (BAS) – If Equipped . . . .471 䡵 POWER STEERING . . . . . . . . . . . . . . . . . . . . .463 ▫ Hill Start Assist (HSA) – If Equipped. . . . . . . .472 ▫ Power Steering Fluid Check . . . . . . . . . . . . . .464 ▫ Hill Descent Control (HDC) – If Equipped (Power Wagon Only) . . . . . . . . . . . . . . . . . .475 䡵 FUEL SAVER TECHNOLOGY 5.7L ENGINE ONLY – IF EQUIPPED . . . . . . . . . . . . .
STARTING AND OPERATING 337 䡵 TIRES — GENERAL INFORMATION . . . . . . . .495 ▫ Tire Spinning . . . . . . . . . . . . . . . . . . . . . . . .502 ▫ Tire Pressure . . . . . . . . . . . . . . . . . . . . . . . .495 ▫ Tread Wear Indicators . . . . . . . . . . . . . . . . . .503 ▫ Tire Inflation Pressures . . . . . . . . . . . . . . . . .496 ▫ Life Of Tire . . . . . . . . . . . . . . . . . . . . . . . . .503 ▫ Tire Pressures For High Speed Operation . . . .498 ▫ Replacement Tires . . . . . . . . . . . . .
338 STARTING AND OPERATING ▫ Tire Pressure Monitor System (TPMS) Tire 䡵 FLEXIBLE FUEL (3.6L/4.7L ENGINE ONLY) Light Load Inflation Switch Description IF EQUIPPED. . . . . . . . . . . . . . . . . . . . . . . (2500 Models) – If Equipped . . . . . . . . . . . . . .518 ▫ E-85 General Information . . . . . . . . . . . . ▫ General Information . . . . . . . . . . . . . . . . . . .522 ▫ Ethanol Fuel (E-85) . . . . . . . . . . . . . . . . . 䡵 FUEL REQUIREMENTS . . . . . . . . . . . . . . . . . .
STARTING AND OPERATING 339 䡵 VEHICLE LOADING . . . . . . . . . . . . . . . . . . . .533 䡵 SNOWPLOW . . . . . . . . . . . . . . . . . . . . . . . . .558 ▫ Certification Label . . . . . . . . . . . . . . . . . . . .533 ▫ 1500 Models Only . . . . . . . . . . . . . . . . . . . . .558 䡵 TRAILER TOWING . . . . . . . . . . . . . . . . . . . . .536 ▫ 2500/3500 Models Only . . . . . . . . . . . . . . . . .559 ▫ Common Towing Definitions . . . . . . . . . . . . .536 䡵 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
340 STARTING AND OPERATING STARTING PROCEDURES Normal Starting Before starting your vehicle, adjust your seat, adjust both Normal starting of either a warm or cold engine is inside and outside mirrors, and fasten your seat belt. obtained without pumping or pressing the accelerator pedal. Turn the key fob to the START position and release The starter should not be operated for more than 15when the engine starts. If the engine fails to start within second intervals.
STARTING AND OPERATING 341 2. Press and hold the brake pedal while pressing the ENGINE START/STOP button once. Tip Start Feature Do not press the accelerator. Turn the ignition switch briefly to the START position and release it. The starter 3. The system takes over and attempts to start the motor will continue to run but will automatically disenvehicle. If the vehicle fails to start, the starter will gage when the engine is running. disengage automatically after 10 seconds.
342 STARTING AND OPERATING 3. If the shift lever/shift selector is not in PARK, the ENGINE START/STOP button must be held for two seconds and vehicle speed must be above 5 mph (8 km/h) before the engine will shut off. The ignition switch position will remain in the ACC position until the shift lever/shift selector is in PARK and the button is pressed twice to the OFF position.
STARTING AND OPERATING 343 4. Press the ENGINE START/STOP button a third time to return the ignition switch to the OFF position (EVIC displays “OFF”). Extreme Cold Weather (Below –20°F Or −29°C) To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (available from your authorized dealer) is recommended. If Engine Fails To Start If the engine fails to start after you have followed the “Normal Starting” procedure, it may be flooded.
344 STARTING AND OPERATING WARNING! (Continued) • If the vehicle has a discharged battery, booster cables may be used to obtain a start from a booster battery or the battery in another vehicle. This type of start can be dangerous if done improperly. Refer to “Jump Starting” in “What To Do In Emergencies” for further information. After Starting The idle speed is controlled automatically and it will decrease as the engine warms up.
STARTING AND OPERATING 345 To Activate The Autostop Mode, The Following Must Autostop, the Climate Controls system may automatiOccur: cally adjust airflow to maintain cabin comfort. Customer settings will be maintained upon return to an engine 1. The system must be in STOP/START READY state. A running condition. STOP/START READY message will be displayed in the Electronic Vehicle Information Center (EVIC) Possible Reasons The Engine Does Not AUTO within the Stop/Start section.
346 STARTING AND OPERATING • Cabin heating or cooling is in process and an accept- To Start The Engine While In Autostop Mode able cabin temperature has not been achieved While in DRIVE the engine will start when the brake • HVAC is set to full defrost mode at a high blower pedal is released or the throttle pedal is depressed. The transmission will automatically reengage upon engine speed restart.
STARTING AND OPERATING 347 • Low brake vacuum (e.g. after several brake pedal • The engine hood has been opened applications) • A STOP/START system error occurs • STOP/START OFF switch is pressed The engine may then be restarted by moving the transmission shift selector out of PARK (e.g. to DRIVE) or, in • 4WD system is put into 4LO mode some cases, only by a KEY START.
348 STARTING AND OPERATING 2. The STOP/START OFF message will appear in Electronic Vehicle Information Center (EVIC). Refer to 1. Press the STOP/START Off switch (located on the “Electronic Vehicle Information Center (EVIC)” in switch bank). The light on the switch will illuminate. “Understanding Your Instrument Panel” for further information. To Manually Turn Off The Start Stop System 3. At the next vehicle stop (after turning off the STOP/ START system) the engine will not be stopped. 4.
STARTING AND OPERATING 349 System Malfunction 1500 Models If there is a malfunction in the STOP/START system, the system will not shut down the engine. A SERVICE STOP/START SYSTEM message will appear in the Electronic Vehicle Information Center (EVIC). Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further information. The engine block heater cord is routed under the hood on the passenger side of the vehicle near the right head lamp assembly.
350 STARTING AND OPERATING WARNING! CAUTION! (Continued) Remember to disconnect the engine block heater cord before driving. Damage to the 110-115 Volt electrical cord could cause electrocution. AUTOMATIC TRANSMISSION • Do not shift between PARK, REVERSE, NEUTRAL, or DRIVE when the engine is above idle speed. • Before shifting into any gear, make sure your foot is firmly pressing the brake pedal. NOTE: You must press and hold the brake pedal while shifting out of PARK.
STARTING AND OPERATING 351 WARNING! WARNING! (Continued) • It is dangerous to shift out of PARK or NEUTRAL if the engine speed is higher than idle speed. If your foot is not firmly pressing the brake pedal, the vehicle could accelerate quickly forward or in reverse. You could lose control of the vehicle and hit someone or something. Only shift into gear when the engine is idling normally and your foot is firmly pressing the brake pedal.
352 STARTING AND OPERATING Key Ignition Park Interlock This vehicle is equipped with a Key Ignition Park Interlock which requires the transmission to be in PARK before the ignition switch can be turned to the full OFF (key removal) position. The key fob can only be removed from the ignition when the ignition is in the full OFF position, and the transmission is locked in PARK whenever the ignition switch is in the full OFF position.
STARTING AND OPERATING 353 The electronically-controlled transmission provides a precise shift schedule. The transmission electronics are self-calibrating; therefore, the first few shifts on a new vehicle may be somewhat abrupt. This is a normal condition, and precision shifts will develop within a few hundred miles (kilometers). Only shift from DRIVE to PARK or REVERSE when the accelerator pedal is released and the vehicle is stopped.
354 STARTING AND OPERATING PARK This range supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. When parking on a level surface, you may shift the transmission into PARK first, and then apply the parking brake. When parking on a hill, apply the parking brake before shifting the transmission to PARK.
STARTING AND OPERATING 355 WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure those in or near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, turn the engine OFF, and remove the key fob. When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.
356 STARTING AND OPERATING CAUTION! • DO NOT race the engine when shifting from PARK or NEUTRAL into another gear range, as this can damage the drivetrain. • Before moving the shift lever out of PARK, you must start the engine, and also press the brake pedal. Otherwise, damage to the shift lever could result. REVERSE This range is for moving the vehicle backward. Shift into REVERSE only after the vehicle has come to a complete stop.
STARTING AND OPERATING 357 CAUTION! Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage. Refer to “Recreational Towing” in “Starting And Operating” and “Towing A Disabled Vehicle” in “What To Do In Emergencies” for further information. DRIVE This range should be used for most city and highway driving. It provides the smoothest upshifts and downshifts, and the best fuel economy.
358 STARTING AND OPERATING Mode is activated. In this mode, the transmission may operate only in certain gears, or may not shift at all. Vehicle performance may be severely degraded and the engine may stall. In some situations, the transmission may not re-engage if the engine is turned off and restarted. The Malfunction Indicator Light (MIL) may be illuminated. A message in the instrument cluster will inform the driver of the more serious conditions, and indicate what actions may be necessary. 2.
STARTING AND OPERATING 359 Electronic Range Select (ERS) Operation – 8 Speed Transmission The Electronic Range Select (ERS) switches allow the driver to limit the highest available gear when the transmission is in DRIVE. For example, if you shift the transmission into 3 (third gear), the transmission will not shift above third gear (except to prevent engine overspeed), but will shift down into second and first gears normally. You can switch between DRIVE and ERS mode at any vehicle speed.
360 STARTING AND OPERATING WARNING! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. When to Use TOW/HAUL Mode When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting occurs, press the TOW/HAUL switch to activate TOW/ HAUL mode.
STARTING AND OPERATING 361 Only shift from DRIVE to PARK or REVERSE when the accelerator pedal is released and the vehicle is stopped. Be sure to keep your foot on the brake pedal when The transmission gear position display (located in the shifting between these gears. instrument cluster) indicates the transmission gear range.
362 STARTING AND OPERATING NOTE: After selecting any gear range, wait a moment to allow the selected gear to engage before accelerating. This is especially important when the engine is cold. PARK This range supplements the parking brake by locking the transmission. The engine can be started in this range. Never attempt to use PARK while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range.
STARTING AND OPERATING 363 WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure those in and near the vehicle. As with all vehicles, you should never exit a vehicle while the engine is running. Before exiting a vehicle, always apply the parking brake, shift the transmission into PARK, turn the engine OFF, and remove the key fob. When the ignition is in the OFF position, the transmission is locked in PARK, securing the vehicle against unwanted movement.
364 STARTING AND OPERATING CAUTION! • Release the shift lever and make sure it is fully seated in the PARK gate. • Before moving the shift lever out of PARK, you must turn the ignition switch from the OFF position to the ON/RUN position, and also press the brake pedal. Otherwise, damage to the shift lever could result. • DO NOT race the engine when shifting from PARK or NEUTRAL into another gear range, as this can damage the drivetrain.
STARTING AND OPERATING 365 WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions. You might lose control of the vehicle and have a collision. CAUTION! Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can cause severe transmission damage.
366 STARTING AND OPERATING If the transmission temperature exceeds normal operating limits, the powertrain controller will modify the transmission shift schedule and expand the range of torque converter clutch engagement. This is done to prevent transmission damage due to overheating. If the transmission becomes extremely hot or is in danger of overheating, the “Transmission Temperature Warning Light” may illuminate and the transmission may operate differently until the transmission cools down.
STARTING AND OPERATING 367 in direct gear regardless of which forward gear is selected. PARK, REVERSE, and NEUTRAL will continue to operate. The Malfunction Indicator Light (MIL) may be illuminated. Limp Home Mode allows the vehicle to be driven to an authorized dealer for service without damaging the transmission. NOTE: Even if the transmission can be reset, we recommend that you visit your authorized dealer at your earliest possible convenience.
368 STARTING AND OPERATING during through-gear accelerations. This additional gear added underdrive gear). Once in ERS mode, tapping ERS can improve vehicle performance and cooling capability (-) or (+) will change the top available gear. when towing a trailer on certain grades. In ERS mode, gears 1 though 3 are underdrive gears, and ERS 4 is direct drive. ERS 5 and 6 (Overdrive gears) are the same as the normal fourth and fifth gears. You can switch between DRIVE and ERS mode at any vehicle speed.
STARTING AND OPERATING 369 WARNING! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. Console Shift Lever To exit ERS mode, simply press and hold the shift lever to the right (+) (console shift) or press the ERS (+) switch (column shift) until “D” is once again displayed in the instrument cluster.
370 STARTING AND OPERATING CAUTION! When To Use TOW/HAUL Mode When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting occurs, press the TOW/HAUL switch to activate TOW/ HAUL mode. This will improve performance and reduce the potential for transmission overheating or failure due to excessive shifting.
STARTING AND OPERATING 371 WARNING! Do not use the “TOW/HAUL” feature when driving in icy or slippery conditions. The increased engine braking can cause the rear wheels to slide, and the vehicle to swing around with the possible loss of vehicle control, which may cause an accident possibly resulting in personal injury or death. Torque Converter Clutch TOW/HAUL Switch The “TOW/HAUL Indicator Light” will illuminate in the instrument cluster to indicate that TOW/HAUL mode has been activated.
372 STARTING AND OPERATING NOTE: • The torque converter clutch will not engage, and the transmission will not shift into the top overdrive gear, until the transmission fluid and engine coolant are warm [usually after 1 to 3 miles (2 to 5 km) of driving]. Because top gear is disabled, and the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting properly when cold. This is normal.
STARTING AND OPERATING 373 Only shift from DRIVE to PARK or REVERSE when the NOTE: After selecting any gear range, wait a moment to accelerator pedal is released and the vehicle is stopped. allow the selected gear to engage before accelerating. Be sure to keep your foot on the brake pedal when This is especially important when the engine is cold. shifting between these gears.
374 STARTING AND OPERATING precaution, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. WARNING! (Continued) • Never use the PARK position as a substitute for the parking brake. Always apply the parking brake fully when parked to guard against vehicle movement and possible injury or damage. • Your vehicle could move and injure you and others if it is not completely in PARK.
STARTING AND OPERATING 375 WARNING! (Continued) CAUTION! • When leaving the vehicle, always remove the key fob and lock your vehicle. • Never leave children alone in a vehicle, or with access to an unlocked vehicle. Allowing children to be in a vehicle unattended is dangerous for a number of reasons. A child or others could be seriously or fatally injured. Children should be warned not to touch the parking brake, brake pedal or the shift lever.
376 STARTING AND OPERATING • Release the shift lever and make sure it is fully seated in the PARK gate. • Look at the transmission gear position display and verify that it indicates the PARK position. • With brake pedal released, verify that the shift lever will not move out of PARK. WARNING! Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe practices that limit your response to changing traffic or road conditions.
STARTING AND OPERATING 377 If the transmission temperature exceeds normal operating limits, the powertrain controller will modify the This range should be used for most city and highway transmission shift schedule and expand the range of driving. It provides the smoothest upshifts and downtorque converter clutch engagement. This is done to shifts, and the best fuel economy. The transmission prevent transmission damage due to overheating.
378 STARTING AND OPERATING During cold temperatures, transmission operation may be modified depending on engine and transmission temperature as well as vehicle speed. This feature improves warm up time of the engine and transmission to achieve maximum efficiency. Engagement of both the torque converter clutch and the top overdrive gear are inhibited until the transmission fluid is warm (refer to the “Note” under “Torque Converter Clutch” in this section).
STARTING AND OPERATING 379 NOTE: Even if the transmission can be reset, we recommend that you visit your authorized dealer at your earliest possible convenience. Your authorized dealer has diagnostic equipment to determine if the problem could recur. shifting between all available gears. Tapping the ERS (-) switch will activate ERS mode, display the current gear in the instrument cluster, and maintain that gear as the top available gear.
380 STARTING AND OPERATING To exit ERS mode, simply press and hold the ERS (+) switch until “D” is once again displayed in the instrument cluster. WARNING! Do not downshift for additional engine braking on a slippery surface. The drive wheels could lose their grip and the vehicle could skid, causing a collision or personal injury. CAUTION! When using ERS for engine braking while descending steep grades, be careful not to overspeed the engine. Apply the brakes as needed to prevent engine overspeed.
STARTING AND OPERATING 381 When To Use TOW/HAUL Mode When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting occurs, press the TOW/HAUL switch to activate TOW/ HAUL mode. This will improve performance and reduce the potential for transmission overheating or failure due to excessive shifting.
382 STARTING AND OPERATING WARNING! Do not use the “TOW/HAUL” feature when driving in icy or slippery conditions. The increased engine braking can cause the rear wheels to slide, and the vehicle to swing around with the possible loss of vehicle control, which may cause an accident possibly resulting in personal injury or death. Torque Converter Clutch A feature designed to improve fuel economy has been included in the automatic transmission on your vehicle.
STARTING AND OPERATING 383 FOUR-WHEEL DRIVE OPERATION — IF EQUIPPED Four-wheel drive trucks are equipped with either a manually shifted transfer case or an electronically shifted transfer case. Refer to the operating instructions for your transfer case, located in this section for further information. Manually Shifted Transfer Case – If Equipped The transfer case provides four mode positions.
384 STARTING AND OPERATING When operating your vehicle in 4L, the engine speed is approximately three times that of the 2H or 4H positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference will adversely affect shifting and can cause damage to the drivetrain.
STARTING AND OPERATING 385 For additional information on the appropriate use of each 4L transfer case mode position, see the information below: Four-Wheel Drive Low Range - This range locks the front and rear driveshafts together forcing the front and rear 2H wheels to rotate at the same speed. Additional traction Rear-Wheel Drive High Range - This range is for normal and maximum pulling power for loose, slippery road street and highway driving on dry hard surfaced roads. surfaces only.
386 STARTING AND OPERATING Shifting Procedure – Manually Shifted Transfer Case 2H To 4H NOTE: • Pausing in transfer case NEUTRAL in vehicles equipped with an automatic transmission may require shutting the engine OFF to avoid gear clash while completing the shift. If difficulty occurs, shift the transmission into NEUTRAL, hold foot on brake, and turn the engine OFF. Make shift to the desired mode. Shifting between 2H and 4H can be made with the vehicle stopped or in motion.
STARTING AND OPERATING 387 Transfer Case Position Indicator Light The “Transfer Case Position Indicator Light” in the instrument cluster is used to alert the driver that the front axle is fully engaged and all four wheels are driving. Electronically Shifted Transfer Case (Four-Position Switch) – If Equipped This is an electronic shift transfer case and is operated by the 4WD Control Switch (Transfer Case Switch), which is located on the instrument panel.
388 STARTING AND OPERATING NOTE: The transfer case NEUTRAL position is selected by pressing the recessed button located on the lower left hand corner of the 4WD Control Switch. The transfer case NEUTRAL position is to be used for recreational towing only. Refer to “Recreational Towing” in “Starting and When additional traction is required, the transfer case Operating” for further information.
STARTING AND OPERATING 389 3. When the shift is complete, the indicator light for the The “SVC 4WD Warning Light” monitors the electronic selected position will stop flashing and remain ON. shift four-wheel drive system. If this light remains on after engine start up or illuminates during driving, it If One Or More Shift Conditions Are Not Met: means that the four-wheel drive system is not function1. The indicator light for the current position will remain ing properly and that service is required. ON. 2.
390 STARTING AND OPERATING When operating your vehicle in 4WD LOW, the engine speed is approximately three times that of the 2WD or 4WD LOCK positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the drivetrain.
STARTING AND OPERATING 391 4WD LOCK Shifting Procedure Four-Wheel Drive Lock Range - This range maximizes NOTE: torque to the front driveshaft, forcing the front and rear • If any of the requirements to select a new transfer case wheels to rotate at the same speed. This range provides position have not been met, the transfer case will not additional traction for loose, slippery road surfaces only. shift.
392 STARTING AND OPERATING 2WD To 4WD LOCK 2WD Or 4WD LOCK To 4WD LOW Rotate the 4WD control switch to the desired position. Shifts between 2WD and 4WD LOCK can be done with the vehicle stopped or in motion. With the vehicle in motion, the transfer case will engage/disengage faster if you momentarily release the accelerator pedal after turning the control switch. If the vehicle is stopped, the ignition switch must be in the ON position with the engine either running or off.
STARTING AND OPERATING 393 Alternate Procedure NOTE: • If Steps 1 or 2 of either the Preferred or Alternate Procedure are not satisfied prior to attempting the 2. With the ignition switch in the ON position and the shift, then the desired position indicator light will flash engine running, shift the transmission into NEUTRAL. continuously while the original position indicator light 3. Rotate the transfer case control switch to the desired is ON, until all requirements have been met. position.
394 STARTING AND OPERATING Electronically Shifted Transfer Case (Five-Position Switch) – If Equipped This electronically shifted transfer case provides five mode positions: This is an electronic shift transfer case and is operated by • Two-wheel drive high range (2WD) the 4WD Control Switch (Transfer Case Switch), which is • Four-wheel drive automatic range (4WD AUTO) located on the instrument panel.
STARTING AND OPERATING 395 NOTE: The transfer case NEUTRAL position is selected by depressing the recessed button located on the lower left hand corner of the 4WD Control Switch. The transfer case NEUTRAL position is to be used for recreational towing only. Refer to “Recreational Towing” in “Starting When additional traction is required, the transfer case and Operating” for further information.
396 STARTING AND OPERATING 3. When the shift is complete, the indicator light for the The “SVC 4WD Warning Light” monitors the electronic selected position will stop flashing and remain ON. shift four-wheel drive system. If this light remains on after engine start up or illuminates during driving, it If One Or More Shift Conditions Are Not Met: means that the four-wheel drive system is not function1. The indicator light for the current position will remain ing properly and that service is required. ON. 2.
STARTING AND OPERATING 397 When operating your vehicle in 4WD LOW, the engine speed is approximately three times that of the 2WD, 4WD AUTO or 4WD LOCK positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the drivetrain.
398 STARTING AND OPERATING 4WD AUTO 4WD LOW Four-Wheel Drive Auto Range - This range sends power to the rear wheels. The four–wheel drive system will be automatically engaged when the vehicle senses a loss of traction. Additional traction for varying road conditions. Four-Wheel Drive Low Range - This range provides low speed four-wheel drive. It maximizes torque to the front driveshaft , forcing the front and rear wheels to rotate at the same speed.
STARTING AND OPERATING 399 Shifting Procedure NOTE: • If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift. The position indicator light for the previous position will remain ON and the newly selected position indicator light will continue to flash until all the requirements for the selected position have been met.
400 STARTING AND OPERATING Electronically Shifted Transfer Case (Five-Position Switch) – If Equipped This electronically shifted transfer case provides five mode positions: This is an electronic shift transfer case and is operated by • Two-wheel drive high range (2WD) the 4WD Control Switch (Transfer Case Switch), which is • Four-wheel drive automatic range (4WD AUTO) located on the instrument panel.
STARTING AND OPERATING 401 NOTE: The transfer case NEUTRAL position is selected by depressing the recessed button (with a ballpoint pen or similar object) located in the center of the 4WD Control Switch. The transfer case NEUTRAL position is to be used for recreational towing only. Refer to “Recreational When additional traction is required, the transfer case Towing” in “Starting and Operating” for further infor4WD LOCK and 4WD LOW positions can be used to mation.
402 STARTING AND OPERATING 3. When the shift is complete, the indicator light for the The “SVC 4WD Warning Light” monitors the electronic selected position will stop flashing and remain ON. shift four-wheel drive system. If this light remains on after engine start up or illuminates during driving, it If One Or More Shift Conditions Are Not Met: means that the four-wheel drive system is not function1. The indicator light for the current position will remain ing properly and that service is required. ON. 2.
STARTING AND OPERATING 403 When operating your vehicle in 4WD LOW, the engine speed is approximately three times that of the 2WD, 4WD AUTO or 4WD LOCK positions at a given road speed. Take care not to overspeed the engine and do not exceed 25 mph (40 km/h). Proper operation of four-wheel drive vehicles depends on tires of equal size, type and circumference on each wheel. Any difference in tire size can cause damage to the drivetrain.
404 STARTING AND OPERATING 4WD AUTO N Four-Wheel Drive Auto Range - This range sends power to the rear wheels. The four–wheel drive system will be automatically engaged when the vehicle senses a loss of traction. Additional traction for varying road conditions. Neutral - This range disengages both the front and rear driveshafts from the powertrain. To be used for flat towing behind another vehicle. Refer to “Recreational Towing” in “Starting and Operating” for further information.
STARTING AND OPERATING 405 will flash until the transfer case completes the shift. 2WD Or 4WD AUTO Or 4WD LOCK To 4WD LOW When the shift is complete, the position indicator light NOTE: When shifting into or out of 4WD LOW some for the selected position will stop flashing and remain gear noise may be heard. This noise is normal and is not ON. detrimental to the vehicle or occupants.
406 STARTING AND OPERATING • The ignition switch must be in the ON position for a shift to take place and for the position indicator lights 1. Bring the vehicle to complete stop. to be operable. If the ignition switch is not in the ON position, then the shift will not take place and no 2. With the ignition switch in the ON position and the position indicator lights will be on or flashing. engine running, shift the transmission into NEUTRAL. Alternate Procedure 3.
STARTING AND OPERATING 407 NOTE: The vehicle will automatically enter Aero Mode when the vehicle speed remains between 62 mph (100 km/h) and 66 mph (106 km/h) for greater than 20 seconds or if the vehicle speed exceeds 66 mph (106 km/h). • Normal Ride Height (NRH) – This is the standard position of the suspension and is meant for normal driving.
408 STARTING AND OPERATING will be automatically lowered to NRH. Off-Road 1 • If the vehicle is in OFFROAD1 or OFFROAD2 setting, be aware of your surroundings, you may not have the may not be available due to vehicle payload, an EVIC clearance required for certain areas and vehicle dammessage will be displayed when this occurs. Refer to age may occur. “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” for further • Aero Mode (Lowers the vehicle approximately .
STARTING AND OPERATING 409 NOTE: Aero Mode may be disabled through vehicle settings in the Electronic Vehicle Information Center (EVIC) or in the Uconnect™ Access 8.4 Radio (If Equipped). Refer to “Electronic Vehicle Information Center (EVIC)” in “Understanding Your Instrument Panel” or “Uconnect™ Access Settings” in “Understanding Your Instrument Panel” for further information. return to Normal Height Mode, press the “Up” button once while in Entry/Exit or drive the vehicle over 15 mph (24 km/h).
410 STARTING AND OPERATING must be closed. If a door is opened at any time while the NOTE: If equipped with a touch screen radio all vehicle is lowering the change will not be completed enabling/disabling of air suspension features must be done through the radio. Refer to “Uconnect™ Access until the open door(s) is closed. Settings” in “Understanding Your Instrument Panel” for This system uses a lifting and lowering pattern which further information.
STARTING AND OPERATING 411 to be disabled. Refer to “Electronic Vehicle Information Wheel Alignment Mode Center (EVIC)” in “Understanding Your Instrument Before performing a wheel alignment this mode must be Panel” for further information. enabled. Refer to “Electronic Vehicle Information Center NOTE: This mode is intended to be enabled with engine (EVIC)” in “Understanding Your Instrument Panel” for further information. running.
412 STARTING AND OPERATING NOTE: If equipped with a touch screen radio all enabling/disabling of air suspension features must be done through the radio. Refer to “Uconnect® Access Settings” in “Understanding Your Instrument Panel” for further information. to achieve. When raising, if multiple indicator lamps are flashing, the highest flashing indicator lamp is the position the system is working to achieve.
STARTING AND OPERATING 413 by one position down to a minimum of Entry/Exit Mode or the lowest position allowed based on current conditions (i.e. vehicle speed, etc.) If vehicle speed is reduced to, and kept below, 15 mph (24 km/h) indicator lamp 4 will flash and indicator lamp 3 will remain solid until Entry/Exit Mode is achieved at which point indicator lamp 4 will turn off. Automatic height changes will occur based on vehicle speed and the current vehicle height.
414 STARTING AND OPERATING AXLE LOCKER SYSTEM (POWER WAGON MODELS ONLY) — IF EQUIPPED CAUTION! This vehicle is equipped with electronically locking front • Do not lock the front or rear axle on hard surfaced roads. The ability to steer the vehicle is reduced and rear differentials. These differentials, when engaged, and damage to the drivetrain may occur when the mechanically lock together the axle shafts forcing the axles are locked on hard surfaced roads. wheels to spin at an equal rate.
STARTING AND OPERATING 415 position, the rear axle is locked. In the FRONT/REAR NOTE: Left to right wheel speed difference may be LOCK position, the front and rear axles are locked. necessary to allow the axle to fully lock.
416 STARTING AND OPERATING NOTE: The rear axle must be locked before the front axle STABILIZER/SWAY BAR SYSTEM — POWER will lock. WAGON ONLY To unlock the front axle; move the axle locker switch to Your vehicle is equipped with an electronic disconnecting REAR LOCK. The FRONT/REAR LOCK indicator light stabilizer/sway bar. This system allows greater front suspension travel in off-road situations. will go out when the axle is unlocked.
STARTING AND OPERATING 417 The system is normally in the On-Road mode, indicated by a solid green light. The stabilizer/sway bar should remain in the On-Road mode during normal driving conditions. WARNING! 1 — On Road 2 — Off Road The switch has two positions; On-Road and Off-Road. Do not disconnect the stabilizer bar and drive on hard surfaced roads or at speeds above 18 mph (29 km/h), you may lose control of the vehicle, which could result in serious injury or death.
418 STARTING AND OPERATING To disconnect the stabilizer/sway bar, shift to either 4HI or 4LO as shown in “Four Wheel Drive Operation” and press the right hand Off Road stabilizer/sway bar button to obtain the Off-Road position. The amber indicator light will flash until the stabilizer/sway bar has been fully disconnected. WARNING! If the stabilizer/sway bar will not return to On-Road mode, vehicle stability is greatly reduced. Do not attempt to drive the vehicle over 18 mph (29 km/h).
STARTING AND OPERATING 419 agency to determine the designated off-road vehicle (ORV) trails or recreation areas. You should always tread lightly and only use established roads, trails or ORV recreational areas. The National Forest Service, Bureau of Land Management or local Department of Natural Resources are a wealth of information and usually have maps with marked trails.
420 STARTING AND OPERATING CAUTION! The door sill height is 25 inches. Water may intrude into the interior of the vehicle at greater depths. Simultaneous Brake And Throttle Operation Many off-road driving conditions require the simultaneous use of the brake and throttle (two footed driving). When climbing rocks, logs, or other stepped objects, using light brake pressure with light throttle will keep the vehicle from jerking or lurching.
STARTING AND OPERATING 421 WARNING! Driving In Snow, Mud And Sand There is a drastic reduction in traction when driving in snow, mud or sand. The vehicle will be less responsive to steering, acceleration and braking inputs. Therefore you should accelerate slowly, leave greater stopping distances and avoid abrupt vehicle maneuvers. You want to keep a When To Use Low Range slow constant steady pace. The key is to maintain the When driving off-road, shift into 4L (Low Range) for vehicle’s momentum.
422 STARTING AND OPERATING CAUTION! On icy or slippery roads, do not downshift at high engine RPMs or vehicle speeds because engine braking may cause skidding and loss of control. • Mud – Deep mud creates a great deal of suction around the tires and is very difficult to get through. You should use 4L (Low Range) with a gear low enough to maintain your momentum without shifting.
STARTING AND OPERATING 423 CAUTION! WARNING! Reduced tire pressures may cause tire unseating and total loss of air pressure. To reduce the risk of tire unseating, while at a reduced tire pressure, reduce your speed and avoid sharp turns or abrupt maneuvers. Crossing obstacles can cause abrupt steering system loading which could cause you to loose control of your vehicle.
424 STARTING AND OPERATING will lift your undercarriage over the obstacle. The tread of the tire is tougher and thicker than the side wall and is designed to take the abuse. Always look ahead and make every effort to cross the large rocks with your tires. CAUTION! • Never attempt to straddle a rock that is large enough to strike your axles or undercarriage. • Never attempt to drive over a rock which is large enough to contact the door sills.
STARTING AND OPERATING 425 CAUTION! CAUTION! Do not attempt to cross a log with a greater diameter than the running ground clearance or the vehicle will become high centered. Winching or rocking the vehicle off hard objects increases the risk of underbody damage. Getting High Centered If you get hung up or high centered on an object, get out of the vehicle and try to determine what the vehicle is hung up on, where it is contacting the underbody and what is the best direction to recover the vehicle.
426 STARTING AND OPERATING the vehicle if something goes wrong? If everything looks good and you feel confident, then change transmission into a lower gear, shift the transfer case into 4L (Low) and proceed with caution. You should use first gear and 4L (Low Range) for very steep hills. fresh ⬙bite⬙ into the surface and will usually provide enough traction to complete the climb.
STARTING AND OPERATING 427 ability to proceed then make sure you are in 4L (Low Range) with the transmission in first gear (manually select first gear on automatic transmissions) and proceed with caution. Allow engine braking to control the descent and apply your brakes if necessary, but do not allow the tires to lock. WARNING! soils. If possible transverse the incline at an angle heading slightly up or down.
428 STARTING AND OPERATING WARNING! If the engine stalls or you lose headway or cannot make it to the top of a steep hill or grade, never attempt to turn around. To do so may result in tipping and rolling the vehicle, which may result in severe injury. Always back carefully straight down a hill in REVERSE. Never back down a hill in NEUTRAL using only the vehicle brakes. Never drive diagonally across a hill, always drive straight up or down.
STARTING AND OPERATING 429 CAUTION! Water ingestion into the axles, transmission, transfer case, engine or vehicle interior can occur if you drive too fast or through too deep of water. Water can cause permanent damage to engine, driveline or other vehicle components and your brakes will be less effective once wet and/or muddy. • Before You Cross Any Type Of Water – As you approach any type of water you need to determine if you can cross it safely and responsibly.
430 STARTING AND OPERATING CAUTION! Muddy waters can reduce the cooling system effectiveness by depositing debris onto the radiator. • Crossing Ditches, Streams, Shallow Rivers Or Other Flowing Water – Flowing water can be extremely dangerous. Never attempt to cross a fast running stream or river even in shallow water. Fast moving water can easily push your vehicle downstream sweeping it out of control.
STARTING AND OPERATING 431 Airing Down For Off-Road Driving Running lower tire pressure off-road can improve your ride comfort and vehicle traction. Reducing the tire air pressure allows the tire to bulge slightly, improving its surface area for better flotation and ability to mold or form to the ground contour. Different terrain, tires, and vehicles require different tire pressure. Hard surfaces like rock and heavier vehicles require higher pressures than softer surfaces such as sand and lighter vehicles.
432 STARTING AND OPERATING vehicle? Is there an anchor point to winch to? Are you CAUTION! alone or do you have another vehicle to help? Is there high risk of vehicle damage during the recovery process? Pulling the vehicle off an obstacle, without first Answering these questions will help you determine the clearing the object, may result in additional underbest method of recovery. If you can still move the vehicle body damage.
STARTING AND OPERATING 433 shift. If after a few rock cycles your vehicle is not free, stop and try another method of recovery. Continuous rock cycling will only cause unnecessary damage to your vehicle and the environment. CAUTION! Damage can occur when spinning your tires at an excessive high speed. Do not spin your tires faster than an indicated 30 mph (48 km/h).
434 STARTING AND OPERATING brakes, once signaled by the other driver. This sequence is important to avoid having the recovered vehicle hit the pulling vehicle. WARNING! Never use tow straps with end hooks or link two straps with a clevis pin. These heavy metal objects could become projectiles if a strap breaks, which could cause severe injury. Never leave more than two or three feet of slack in the strap. More slack than this greatly increases the risk of injury and vehicle damage.
STARTING AND OPERATING 435 floor mat or something else over the strung out cable. Placing something over the strung out cable helps keep the cable on the ground if it breaks. Next, place the vehicle in first gear and apply a very light throttle as you power the winch in. Be careful not to allow slack in the cable as you recover the vehicle. Do not try to guide the cable into the drum. If it starts to bunch up on one end, let it. You can re-spool the cable afterwards.
436 STARTING AND OPERATING • Check for accumulations of plants or brush. These • If you experience unusual vibration after driving in things could be a fire hazard. They might hide damage mud, slush or similar conditions, check the wheels for to fuel lines, brake hoses, axle pinion seals, and impacted material. Impacted material can cause a propeller shafts. wheel imbalance and freeing the wheels of it will correct the situation.
STARTING AND OPERATING 437 will supply maximum traction. When starting with only DRIVING ON SLIPPERY SURFACES one rear wheel on an excessively slippery surface, slight Acceleration momentary application of the parking brake may be Rapid acceleration on snow covered, wet, or other slipnecessary to gain maximum traction. pery surfaces may cause the driving wheels to pull erratically to the right or left.
438 STARTING AND OPERATING Traction DRIVING THROUGH WATER When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface. This is known as hydroplaning and may cause partial or complete loss of vehicle control and stopping ability. To reduce this possibility, the following precautions should be observed: Driving through water more than a few inches/ centimeters deep will require extra caution to ensure safety and prevent damage to your vehicle. 1.
STARTING AND OPERATING 439 Shallow Standing Water CAUTION! (Continued) Although your vehicle is capable of driving through shallow standing water, consider the following Caution and Warning before doing so. CAUTION! • Always check the depth of the standing water before driving through it. Never drive through standing water that is deeper than the bottom of the tire rims mounted on the vehicle.
440 STARTING AND OPERATING WARNING! • Driving through standing water limits your vehicle’s traction capabilities. Do not exceed 5 mph (8 km/h) when driving through standing water. • Driving through standing water limits your vehicle’s braking capabilities, which increases stopping distances. Therefore, after driving through standing water, drive slowly and lightly press on the brake pedal several times to dry the brakes.
STARTING AND OPERATING 441 always a good idea to check for damage. That way you • After extended operation in mud, sand, water, or can get any problems taken care of right away and have similar dirty conditions, have the radiator, fan, brake rotors, wheels, brake linings, and axle yokes inspected your vehicle ready when you need it. and cleaned as soon as possible. • Completely inspect the underbody of your vehicle. Check tires, body structure, steering, suspension, and WARNING! exhaust system for damage.
442 STARTING AND OPERATING WINCH USAGE (POWER WAGON ONLY) — IF EQUIPPED Things To Know Before Using Your Winch General Winch Information Tensioning The Wire Rope The winch rope must be properly tensioned before use. Follow the instructions below to tension the rope: 1. Un-spool the wire rope leaving five wraps of rope on the winch drum. Your vehicle is equipped with an electric vehicle recovery winch. This winch uses the electrical power from the 2. Attach the hook to a suitable anchor point.
STARTING AND OPERATING 443 CAUTION! Winch Motor Thermal Protection Your winch is equipped with a thermal protection device in the motor. If the winch is operated for an excessive duration, the device may interrupt motor function to protect the winch motor. During this time the winch will power-out but will not power-in. Allow the winch motor Low Voltage Interrupt to cool for a few minutes before continuing to winch.
444 STARTING AND OPERATING Understanding The Features Of Your Winch Winch Components
STARTING AND OPERATING 445 1. Motor: The winch motor is powered by the vehicle 6. Clutch Lever: The clutch lever allows the winch drum charging system and features a thermal protection to be disconnected from the winch motor to allow the wire rope to be pulled from the winch by hand. switch that automatically stops motor function in the power-in direction if the motor gets too hot. 7. Remote Control: The remote control provides the 2.
446 STARTING AND OPERATING Winch Accessories The following accessories are necessary to attach the winch to anchors, change direction of pull, and for safe winching. Gloves: Wire rope, through use, will develop ⬙barbs⬙ which can slice skin. It is extremely important to wear protective gloves while operating the winch or handling the wire rope. Avoid loose fitting clothes or anything that could become entangled in the wire rope and other moving parts.
STARTING AND OPERATING 447 Clevis/D-Shackles: The D-Shackle is a safe means of connecting the looped ends of cables, straps and snatch blocks. The shackle’s pin is threaded to allow easy removal. Tree Trunk Protector: Typically made of tough, highquality nylon, it provides the operator an attachment point for the winch rope to a wide variety of anchor points and objects, as well as protect living trees.
448 STARTING AND OPERATING Operating Your Winch WARNING! (Continued) WARNING! Failure to observe any of these warnings regarding proper winch usage may result in severe injury. • Always use supplied hook strap to hold the hook when spooling wire rope in or out. • Never use as a hoist. • Never use to move persons. • Never exceed winch or wire rope rated capacity. • Always wear heavy leather gloves when handling the wire rope. • Never touch wire rope or hook while in tension or under load.
STARTING AND OPERATING 449 WARNING! (Continued) • Always disconnect the remote control when not in use. • Never winch when there are less than five wraps of wire rope around the winch drum. • Always pass remote control through a window to avoid pinching lead in door, then using remote inside a vehicle. • Never leave the remote control plugged into the winch while free spooling, rigging or sitting idle. General Information Practice using your winch before you get stuck.
450 STARTING AND OPERATING CAUTION! (Continued) • Always inspect winch installation and wire rope condition before operating the winch. Frayed, kinked or damaged wire rope must be replaced immediately. Loose or damaged winch installation must be corrected immediately. • Always be sure any element which can interfere with safe winching operations is removed prior to initiating winching. • Always keep remote control lead clear of the drum, wire rope and rigging.
STARTING AND OPERATING 451 3. Disengage the clutch to allow free spooling of the 4. Free the winch hook and attach the hook strap. Free winch drum, rotate the clutch lever on the winch to the winch hook from its anchor point. Attach the hook disengage. Freespooling conserves battery power. strap to the hook (if not attached).
452 STARTING AND OPERATING 5. Pull the wire to the anchor point. Pull out enough wire 6. Secure to the anchor point. Once you have established rope to reach your anchor point. Be sure to keep a your anchor point, secure the tree-trunk protector or certain amount of tension on the wire as it can become choker-chain around the object. twisted and over-wrapped when slackened, leading to wire rope damage. To prevent losing the end, hold the hook strap while you work.
STARTING AND OPERATING 453 CAUTION! Always be certain the anchor you select will withstand the load. NOTE: How to choose an anchor point: A secure anchor is critical to winching operations. An anchor must be strong enough to hold while winching. Natural anchors include trees, stumps and rocks. Hook the cable as low as possible. If no natural anchors are available when recovering another vehicle, your vehicle becomes the anchor point.
454 STARTING AND OPERATING 8. Lock the clutch. Lock the winch drum by rotating the clutch lever on the winch to engage. NOTE: Always ensure the clutch is fully engaged or disengaged. 9. Connect the remote control to the winch control box, located behind the front bumper. Be careful not to let the remote control cord dangle in front of the winch. If you choose to control the winch from inside your vehicle, always pass the remote through a window to avoid pinching the cord in the door.
STARTING AND OPERATING 455 10. Put wire rope under tension. Using the remote con- 12. Check wire rope. The wire rope should be neatly trol switch, slowly wind the wire rope until no slack wound around the spooling drum. Improper winding can cause damage to the wire rope. remains. Once the wire rope is under tension, stand well clear of it and never step over it. 5 11. Check your anchor. Make sure all connections are secured and free of debris before continuing with the winching procedure.
456 STARTING AND OPERATING In certain situations you may decide to throw a heavy blanket or similar object over the wire rope. A heavy blanket can absorb energy should the wire rope break. Place it on the wire rope midway between the winch and the anchor point. Do this before the wire rope is put under tension. Do not approach or move the blanket once tension is applied. Do not allow it to get pulled into the fairlead.
STARTING AND OPERATING 457 14. Begin winching. With the winching vehicles engine on and light tension already on the wire rope, begin winching slowly and steadily. Be sure that the wire rope is winding evenly and tightly around the spooling drum. For additional assistance, the winched vehicle can be slowly driven while being pulled by the winch. Continue pulling until the vehicle is on stable ground. If you are able to drive the vehicle, the winching operation is complete.
458 STARTING AND OPERATING • What to look for under load: The wire rope must 15. Secure vehicle. Once recovery of the vehicle is comalways spool onto the drum as indicated by the plete, be sure to secure the vehicle’s brakes and shift the transmission to PARK. Release tension in the wire drum rotation decal on the winch. As you power-in, rope. make sure the wire rope winds evenly and tightly on the drum. This prevents the outer wire wraps from 16.
STARTING AND OPERATING 459 WARNING! To prevent serious injury, NEVER put your fingers inside the hook area as you are powering-in. NOTE: How to spool under no load: Arrange the remote control lead so it cannot be caught in the winch. Arrange the wire rope so it will not kink or tangle when spooled. Be sure any wire rope already on the spooling drum is wound tightly and evenly layered. Tighten and straighten the layer if necessary.
460 STARTING AND OPERATING 18. Store the hook on the most outboard loop of the tow 19. Disconnect the remote control. Disconnect the remote hook. control cord from the control box and store in a clean and dry place. Winching operations are now complete. Put the cap on the solenoid plug-in. NOTE: Always store the remote control in a protected, clean, dry area. Rigging Techniques Various winching situations will require application of other winching techniques.
STARTING AND OPERATING 461 How To Change The Pulling Direction All winching operations should have a straight line from the winch to the object being pulled. This minimizes the wire rope collecting on one side of the drum affecting pulling efficiency and damaging wire rope. A snatch block, secured to a point directly in front of the vehicle will enable you to change your pulling direction while still allowing the wire rope to be at 90° to wind properly onto the spooling drum.
462 STARTING AND OPERATING Double Line Because pulling power decreases with the number of layers of wire rope on the winch drum, you can use a snatch block to double line out more wire rope. This decreases the number of layers of wire rope on the drum, and increases pulling power. Start by feeding out enough wire rope to free the winch hook. Attach the hook to your vehicle’s frame/tow hook and run the wire rope through a snatch block.
STARTING AND OPERATING 463 • Upon initial start-up in cold weather, the power steering pump may make noise for a short amount of time. The standard power steering system will give you good This is due to the cold, thick fluid in the steering vehicle response and increased ease of maneuverability system. This noise should be considered normal, and it in tight spaces. The system will provide mechanical does not in any way damage the steering system. steering capability if power assist is lost.
464 STARTING AND OPERATING Power Steering Fluid Check WARNING! (Continued) Checking the power steering fluid level at a defined service parts and to ensure accurate fluid level reading. Do interval is not required. The fluid should only be checked if not overfill. Use only manufacturer’s recommended a leak is suspected, abnormal noises are apparent, and/or power steering fluid. the system is not functioning as anticipated. Coordinate inspection efforts through an authorized dealer.
STARTING AND OPERATING 465 PARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied. Also, be certain to leave the transmission in PARK. The foot operated parking brake is located below the lower left corner of the instrument panel. To apply the park brake, firmly push the park brake pedal fully. To release the parking brake, pull the parking brake release handle.
466 STARTING AND OPERATING NOTE: • When the parking brake is applied and the transmission is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime will sound to alert the driver. Fully release the parking brake before attempting to move the vehicle. • This light only shows that the parking brake is applied. It does not show the degree of brake application.
STARTING AND OPERATING 467 WARNING! (Continued) • Be sure the parking brake is fully disengaged before driving; failure to do so can lead to brake failure and a collision. • Always fully apply the parking brake when leaving your vehicle or it may roll and cause damage or injury. Also, be certain to leave the transmission in PARK. Failure to do so may cause the vehicle to roll and cause damage or injury.
468 STARTING AND OPERATING Four-Wheel Anti-Lock Brake System WARNING! The Four-Wheel Anti-Lock Brake System contains sophisticated electronic equipment. It may be susceptible to interference caused by improperly installed or high output radio transmitting equipment. This interference can cause possible loss of anti-lock braking capability. Installation of such equipment should be performed by qualified professionals. The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure.
STARTING AND OPERATING 469 ABS Warning Light WARNING! (Continued) The ABS includes an amber warning light. When the light is illuminated, the ABS is not functioning. The system reverts to standard, non-anti-lock brakes. WARNING! • Pumping of the anti-lock brakes will diminish their effectiveness and may lead to a collision. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop.
470 STARTING AND OPERATING ELECTRONIC BRAKE CONTROL SYSTEM Your vehicle is equipped with an advanced electronic brake control system that includes Anti-Lock Brake System (ABS), Traction Control System (TCS), Brake Assist System (BAS), Electronic Roll Mitigation (ERM), Hill Start Assist (HSA), Electronic Stability Control (ESC) and Trailer Sway Control (TSC). All of the systems work together to enhance vehicle stability and control in various driving conditions, and are commonly referred to as ESC.
STARTING AND OPERATING 471 power is reduced to provide enhanced acceleration and stability. A feature of the TCS functions similarly to a limited-slip differential and controls the wheel spin across a driven axle. If one wheel on a driven axle is spinning faster than the other, the system will apply the brake of the spinning wheel. This will allow more engine torque to be applied to the wheel that is not spinning. This feature remains active even if TCS and ESC are in the “Partial Off” mode.
472 STARTING AND OPERATING WARNING! (Continued) • The BAS cannot prevent collisions, including those resulting from excessive speed in turns, following another vehicle too closely, or hydroplaning. • The capabilities of a BAS-equipped vehicle must never be exploited in a reckless or dangerous manner which could jeopardize the user’s safety or the safety of others. Hill Start Assist (HSA) – If Equipped and the vehicle will roll down the incline.
STARTING AND OPERATING 473 • Gear selection matches vehicle uphill direction (i.e., The system will work in REVERSE and all forward gears, vehicle facing uphill is in forward gear; vehicle back- and will not activate if the vehicle is placed in NEUing uphill is in REVERSE gear). TRAL. WARNING! There may be situations on minor hills (i.e.
474 STARTING AND OPERATING WARNING! WARNING! (Continued) • If you use a trailer brake controller with your trailer, your trailer brakes may be activated and deactivated with the brake switch. If so, when the brake pedal is released, there may not be enough brake pressure to hold the vehicle and trailer on a hill and this could cause a collision with another vehicle or object behind you.
STARTING AND OPERATING 475 4. Press the “ESC Off” switch four times within 20 Customer Programmable Features” in “Understanding seconds. The “ESC Off Indicator Light” should appear Your Instrument Panel” for further information. and disappear four times. Hill Descent Control (HDC) – If Equipped (Power 5. Rotate the steering wheel 360° clockwise (180° clock- Wagon Only) wise from center). HDC is only intended for low speed off-road driving.
476 STARTING AND OPERATING When enabled, HDC senses the terrain and activates in the usual manner. When either the brake or the when the vehicle is descending a hill. HDC speed may be accelerator is released, HDC will control the vehicle at the adjusted by the driver to suit the driving conditions. The original set speed. speed corresponds to the transmission gear selected. Enabling HDC Gear 1st 2nd 3rd 4th 5th 6th REVERSE Approximate HDC Set Speed 1 mph (1.5 km/h) 2.5 mph (4 km/h) 4 mph (6.5 km/h) 5.
STARTING AND OPERATING 477 All Two-Wheel Drive Vehicles And Four-Wheel The ESC system enhances directional control and stabil- Drive Vehicles In 2WD, 4WD AUTO, Or 4WD ity of the vehicle under various driving conditions. ESC LOCK Modes Can Choose The Following ESC corrects for oversteering or understeering of the vehicle Operating Modes: by applying the brake of the appropriate wheel to assist ESC On in counteracting the oversteer or understeer condition.
478 STARTING AND OPERATING WARNING! Electronic Stability Control (ESC) cannot prevent the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by prevailing road conditions. ESC cannot prevent accidents, including those resulting from excessive speed in turns, driving on very slippery surfaces, or hydroplaning. ESC also cannot prevent accidents resulting from loss of vehicle control due to inappropriate driver input for the conditions.
STARTING AND OPERATING 479 NOTE: To improve the vehicle’s traction when driving with snow chains or starting off in deep snow, sand or gravel, it may be desirable to switch to the “Partial Off” mode by pressing the “ESC Off” switch. Once the situation requiring ESC to be switched to the “Partial Off” mode is overcome, turn ESC back on by momentarily pressing the “ESC Off” switch. This may be done while the vehicle is in motion.
480 STARTING AND OPERATING In this mode, ESC and TCS except for the “limited slip” WARNING! feature described in the TCS section are turned off until the vehicle reaches a speed of 40 mph (64 km/h). At In the ESC ⴖFull Offⴖ mode, the engine torque reduc40 mph (64 km/h) the system returns to “Partial Off” tion and stability features are disabled. Therefore, mode, described above. When the vehicle speed drops the enhanced vehicle stability offered by ESC is below 35 mph (56 km/h) the ESC system shuts off.
STARTING AND OPERATING 481 malfunction has been detected in the ESC system. If this NOTE: light remains on after several ignition cycles, and the • The “ESC Activation/Malfunction Indicator Light” vehicle has been driven several miles (kilometers) at and the “ESC OFF Indicator Light” come on momenspeeds greater than 30 mph (48 km/h), see your authotarily each time the ignition switch is turned ON. rized dealer as soon as possible to have the problem diagnosed and corrected.
482 STARTING AND OPERATING Trailer Sway Control (TSC) – If Equipped The TSC system uses sensors in the vehicle to recognize an excessively swaying trailer and will take the appropriate actions to attempt to stop the sway. The system may reduce engine power and apply the brake of the appropriate wheel(s) to counteract the sway of the trailer. TSC will become active automatically once an excessively swaying trailer is recognized. No driver action is required.
STARTING AND OPERATING 483 TIRE SAFETY INFORMATION Tire Markings 5 1 — U.S.
484 STARTING AND OPERATING • Temporary spare tires are spares designed for temporary emergency use only. Temporary high pressure • P (Passenger) - Metric tire sizing is based on U.S. compact spare tires have the letter “T” or “S” molded design standards. P-Metric tires have the letter “P” into the sidewall preceding the size designation. Exmolded into the sidewall preceding the size designaample: T145/80D18 103M. tion. Example: P215/65R15 95H. • High flotation tire sizing is based on U.S.
STARTING AND OPERATING 485 Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ⴖ....blank....ⴖ = Passenger car tire based on European design standards LT = Light truck tire based on U.S. design standards T or S = Temporary spare tire 31 = Overall diameter in inches (in) 215 = Section width in millimeters (mm) 65 = Aspect ratio in percent (%) — Ratio of section height to section width of tire 10.
486 STARTING AND OPERATING EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions — The maximum speed corresponding to the speed symbol should only be achieved under specified operating conditions (i.e.
STARTING AND OPERATING 487 Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side. Tires the outboard side, then you will find it on the inboard side of the tire. with white sidewalls will have the full TIN, including the date code, located on the white sidewall side of the tire.
488 STARTING AND OPERATING EXAMPLE: DOT MA L9 ABCD 0301 01 = Number representing the year in which the tire was manufactured (two digits) — 01 means the year 2001 — Prior to July 2000, tire manufacturers were only required to have one number to represent the year in which the tire was manufactured.
STARTING AND OPERATING 489 Tire Terminology And Definitions Term B-Pillar Cold Tire Inflation Pressure Maximum Inflation Pressure Recommended Cold Tire Inflation Pressure Tire Placard Definition The vehicle B-Pillar is the structural member of the body located behind the front door. Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
490 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
STARTING AND OPERATING 491 Tire And Loading Information Placard 2) total weight your vehicle can carry 3) tire size designed for your vehicle 4) cold tire inflation pressures for the front, rear, and spare tires. Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle.
492 STARTING AND OPERATING To determine the maximum loading conditions of your 4. The resulting figure equals the available amount of vehicle, locate the statement “The combined weight of cargo and luggage load capacity. For example, if occupants and cargo should never exceed XXX lbs or “XXX” amount equals 1,400 lbs (635 kg) and there will XXX kg” on the Tire and Loading Information placard.
STARTING AND OPERATING 493 • For the following example, the combined weight of occupants and cargo should never exceed 865 lbs • The following table shows examples on how to calcu(392 kg). late total load, cargo/luggage, and towing capacities of your vehicle with varying seating configurations and number and size of occupants. This table is for illustration purposes only and may not be accurate for the seating and load carry capacity of your vehicle.
494 STARTING AND OPERATING
STARTING AND OPERATING 495 WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES — GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
496 STARTING AND OPERATING WARNING! (Continued) • Always drive with each tire inflated to the recommended cold tire inflation pressure. Economy Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Under-inflation also increases tire rolling resistance resulting in higher fuel consumption.
STARTING AND OPERATING 497 CAUTION! After inspecting or adjusting the tire pressure, always reinstall the valve stem cap. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem. Tire pressures change by approximately 1 psi (7 kPa) per 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in the Winter.
498 STARTING AND OPERATING Tire Pressures For High Speed Operation The manufacturer advocates driving at safe speeds and within posted speed limits. Where speed limits or conditions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important. Increased tire pressure and reduced vehicle loading may be required for high-speed vehicle operation.
STARTING AND OPERATING 499 the tire sidewall. Use all season tires only in sets of four; If you need snow tires, select tires equivalent in size and failure to do so may adversely affect the safety and type to the original equipment tires. Use snow tires only in sets of four; failure to do so may adversely affect the handling of your vehicle. safety and handling of your vehicle.
500 STARTING AND OPERATING Spare Tire Matching Original Equipped Tire And Wheel – If Equipped Your vehicle may be equipped with a spare tire and wheel equivalent in look and function to the original equipment tire and wheel found on the front or rear axle of your vehicle. This spare tire may be used in the tire rotation for your vehicle. If your vehicle has this option refer to an authorized tire dealer for the recommended tire rotation pattern.
STARTING AND OPERATING 501 WARNING! (Continued) replaced. Be sure to follow the warnings, which apply to your spare. Failure to do so could result in spare tire failure and loss of vehicle control. Full Size Spare – If Equipped The full size spare is for temporary emergency use only. This tire may look like the originally equipped tire on the front or rear axle of your vehicle, but it is not. This spare tire may have limited tread life.
502 STARTING AND OPERATING WARNING! Limited-use spares are for emergency use only. Installation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the speed listed on the limit-use spare wheel. Keep inflated to the cold tire inflation pressures listed on your Tire and Loading Information Placard located on the driver’s side B-Pillar or the rear edge of the driver’s side door.
STARTING AND OPERATING 503 These indicators are molded into the bottom of the tread Tread wear indicators are in the original equipment tires grooves. They will appear as bands when the tread depth to help you in determining when your tires should be becomes 1/16 in (2 mm). When the tread is worn to the tread wear indicators, the tire should be replaced. Refer replaced. to replacement tires in this section for further information.
504 STARTING AND OPERATING WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread. Failure to follow this warning can result in sudden tire failure. You could lose control and have a collision resulting in serious injury or death. Information placard or the Vehicle Certification Label for the size designation of your tire. The Load Index and Speed Symbol for your tire will be found on the original equipment tire sidewall.
STARTING AND OPERATING 505 WARNING! WARNING! (Continued) • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combinations of unapproved tires and wheels may change suspension dimensions and performance characteristics, resulting in changes to steering, handling, and braking of your vehicle. This can cause unpredictable handling and stress to steering and suspension components. You could lose control and have a collision resulting in serious injury or death.
506 STARTING AND OPERATING TIRE CHAINS CAUTION! (Continued) NOTE: Chains must be the proper size for the vehicle as recommended by the chain manufacturer. CAUTION! To avoid damage to your vehicle or tires, observe the following precautions: • Because of restricted traction device clearance between tires and other suspension components, it is important that only traction devices in good condition are used. Broken devices can cause serious damage.
STARTING AND OPERATING 507 These cautions apply to all chain traction devices, including link and cable (radial) chains. NOTE: • On 4x2 and 4x4 1500 model trucks, the use of class “S” snow chains is permitted on the rear wheels only of trucks equipped with P265/70R17 tires. • On 4x2 2500 model trucks, the use of class “U” snow chains is permitted on the rear wheels only of trucks equipped with LT245/70R17 or LT265/70R17 tires.
508 STARTING AND OPERATING The suggested rotation method is the “forward cross” shown in the following diagram. This rotation pattern Tires on the front and rear axles of vehicles operate at does not apply to some directional tires that must not be different loads and perform different steering, driving, reversed. and braking functions. For these reasons, they wear at unequal rates. TIRE ROTATION RECOMMENDATIONS These effects can be reduced by timely rotation of tires.
STARTING AND OPERATING 509 Directional Tires – If Equipped Dual Rear Wheels – If Equipped For the R/T package with 22” tires and wheels, the rotational direction of the tire must be taken into consideration when rotating the tires. The recommended rotation pattern for directional tires is shown below. The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires.
510 STARTING AND OPERATING CAUTION! 3500 Dual Rear Tires may only have one approved direction of rotation. This is to accommodate the asymmetrical design (tread pattern) of the On/OffRoad tire and the use of Outline White Letter (OWL) tires. • When replacing a flat, the spare tire may have to be remounted on the rim, or installed at a different location, to maintain the correct placement of the tire on the wheel relative to the tire/wheel position on the truck.
STARTING AND OPERATING 511 also increase as the vehicle is driven - this is normal and to be driven for up to 20 minutes above 15 mph there should be no adjustment for this increased pres- (25 km/h) in order for the TPMS to receive this information. sure. The TPMS will warn the driver of a low tire pressure if the tire pressure falls below the low-pressure warning limit for any reason, including low temperature effects and natural pressure loss through the tire.
512 STARTING AND OPERATING CAUTION! • The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage.
STARTING AND OPERATING 513 • Seasonal temperature changes will affect tire pressure, The matching full size spare wheel and tire assembly (if and the TPMS will monitor the actual tire pressure in equipped) has a TPM sensor. The matching full size spare can be used in place of any of the four road tires. The the tire. TPMS will only monitor the pressure in the full size spare Base System when it is used in place of a road tire.
514 STARTING AND OPERATING to the vehicle’s recommended cold placard pressure 1. Signal interference due to electronic devices or driving next to facilities emitting the same radio frequencies as value as shown in the ⬙Inflate to XX⬙ message. Once the the TPM sensors. system receives the updated tire pressures, the system will automatically update and the “Tire Pressure Moni2.
STARTING AND OPERATING 515 displayed, and the “Tire Pressure Monitoring Telltale The TPMS consists of the following components: Light” will turn ON. An ⬙Inflate to XX⬙ message will • Receiver module, also be displayed. • Four TPM sensors, 3.
516 STARTING AND OPERATING will sound when tire pressure is low in one or more of the four active road tires. In addition, the EVIC will display a “LOW TIRE PRESSURE” message for a minimum of five seconds and a graphic showing the pressure values of each tire with the low tire pressure values flashing or in a different color. An ⬙Inflate to XX⬙ message will also be displayed.
STARTING AND OPERATING 517 and then display dashes (- -) in place of the pressure SYSTEM⬙ message will no longer display, and a pressure value to indicate which sensor is not being received. value will display in place of the dashes. A system fault can occur due to any of the following: 1. Signal interference due to electronic devices or driving next to facilities emitting the same radio frequencies as the TPM sensors. 2.
518 STARTING AND OPERATING message is then followed with a graphic display with 3. After driving the vehicle for up to 20 minutes above pressure values still shown.
STARTING AND OPERATING 519 WARNING! (Continued) Supplemental Tire Pressure Information Label which is located on the rear face of the driver door opening. Failure to do so may cause you to lose control resulting in an accident, causing serious or fatal injury.
520 STARTING AND OPERATING Tire Light Load Inflation Switch Operation – If Equipped • This vehicle may have different recommended tire pressure values between the front and rear tires as shown in both the Tire Loading Information Label and the Supplemental Tire Pressure Information Label. It is also equipped to be driven with tire pressures appropriate to either a Light Load condition or the vehicle Max Load condition.
STARTING AND OPERATING 521 Tire Pressure Information label. The Supplemental Tire Pressure Information label is located on the rear face of the driver door opening. Use an accurate tire gauge to check the tire pressures when lowering all four tire pressures. The vehicle may need to be driven above 15 mph (25 km/h) to receive this updated pressure information. After all four tire pressures have been lowered to the Light Load inflation pressures, press the tire light load inflation switch.
522 STARTING AND OPERATING To switch back to the max load inflation pressure (cold) low pressure warning threshold, press the tire light load inflation switch. It is not necessary to first fill the tires to the max load inflation pressure (cold) values to switch the TPMS system to the max load inflation pressure (cold) low pressure warning threshold.
STARTING AND OPERATING 523 FUEL REQUIREMENTS 5.7L Engine 3.6L And 4.7L Engine These engines are designed to meet all emissions regulations and provide excellent fuel economy and performance when using high quality unleaded “regular” gasoline having an octane rating of 87. The use of premium gasoline is not recommended, as it will not provide any benefit over regular gasoline in these engines.
524 STARTING AND OPERATING Over 40 auto manufacturer’s world wide have issued and endorsed consistent gasoline specifications (the Worldwide Fuel Charter, WWFC) which define fuel properties necessary to deliver enhanced emissions, performance, and durability for your vehicle. The manufacturer recommends the use of gasolines that meet the WWFC specifications, if they are available. Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with oxygenates such as 10% ethanol, MTBE, and ETBE.
STARTING AND OPERATING 525 • disconnect and reconnect the battery to reset the engine controller memory Non-FFV vehicles are compatible with gasoline containing 10% ethanol (E10). Gasoline with higher ethanol More extensive repairs will be required for prolonged content may void the vehicle’s warranty. exposure to E-85 fuel.
526 STARTING AND OPERATING Materials Added To Fuel CAUTION! (Continued) All gasoline sold in the United States is required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and they would result in additional cost. Therefore, you should not have to add anything to the fuel. Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law.
STARTING AND OPERATING 527 Carbon Monoxide Warnings WARNING! (Continued) WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas, which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
528 STARTING AND OPERATING E-85 Fuel Cap CAUTION! Only vehicles with the E-85 fuel filler door label can operate on E-85. E-85 Badge Ethanol Fuel (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline.
STARTING AND OPERATING 529 WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smoking materials lit in or near the vehicle when removing the fuel filler tube cap (gas cap) or filling the tank. Do not use E-85 as a cleaning agent and never use it near an open flame.
530 STARTING AND OPERATING Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles FFV vehicles operated on E-85 require specially formulated engine oils. These special requirements are included in MOPAR® engine oils, and in equivalent oils meeting Chrysler Specification MS-6395. The manufacturer only recommends engine oils that are API Certified and meet the requirements of Material Standard MS-6395.
STARTING AND OPERATING 531 CAUTION! Replacing fuel system components with non-ethanol compatible components can damage your vehicle. Maintenance ADDING FUEL The fuel filler cap (gas cap) is located behind the fuel filler door, on the left side of the vehicle. Open the fuel door and remove the fuel cap by turning it counterclockwise. CAUTION! 5 Do not use ethanol mixture greater than 85% in your vehicle. It will cause difficulty in cold starting and may affect driveability.
532 STARTING AND OPERATING NOTE: When removing the fuel filler cap, lay the cap tether in the hook, located on the fuel filler door. CAUTION! • Damage to the fuel system or emissions control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap could let impurities into the fuel system. • A poorly fitting gas cap may cause the “Malfunction Indicator Light (MIL)” to turn on.
STARTING AND OPERATING 533 • When the fuel nozzle “clicks” or shuts off, the fuel tank Loose Fuel Filler Cap Message is full. WARNING! Static electricity can cause an ignition of flammable liquid, vapor or gas in any vehicle or trailer. To reduce risk of serious injury or death when filling containers: • Always place container on the ground before filling. • Keep the pump nozzle in contact with the container when you are filling it. • Use only approved containers for flammable liquid.
534 STARTING AND OPERATING This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Rating (GAWR) front and rear, and Vehicle Identification Number (VIN). A Month-Day-Hour (MDH) number is included on this label and indicates the Month, Day and Hour of manufacture. The bar code that appears on the bottom of the label is your VIN. Gross Axle Weight Rating (GAWR) The GAWR is the maximum permissible load on the front and rear axles.
STARTING AND OPERATING 535 Inflation Pressure This is the cold tire inflation pressure for your vehicle for all loading conditions up to full GAWR. Curb Weight The weight on the front and rear of the vehicle should then be determined separately to be sure that the load is properly distributed over the front and rear axle. Weighing the vehicle may show that the GAWR of either the front or rear axles has been exceeded but the total load is within the specified GVWR.
536 STARTING AND OPERATING CAUTION! (Continued) parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control. Also overloading can shorten the life of your vehicle. Common Towing Definitions The following trailer towing related definitions will assist you in understanding the following information: Gross Vehicle Weight Rating (GVWR) The GVWR is the total allowable weight of your vehicle.
STARTING AND OPERATING 537 measure GTW is to put your fully loaded trailer on a vehicle scale. The entire weight of the trailer must be supported by the scale. Gross Combination Weight Rating (GCWR) The GCWR is the total permissible weight of your vehicle and trailer when weighed in combination. WARNING! It is important that you do not exceed the maximum front or rear GAWR. A dangerous driving condition can result if either rating is exceeded. You could lose control of the vehicle and have an accident.
538 STARTING AND OPERATING Trailer Sway Control Weight-Distributing Hitch The trailer sway control can be a mechanical telescoping link that can be installed between the hitch receiver and the trailer tongue that typically provides adjustable friction associated with the telescoping motion to dampen any unwanted trailer swaying motions while traveling. A weight-distributing system works by applying leverage through spring (load) bars.
STARTING AND OPERATING 539 WARNING! • An improperly adjusted weight distributing hitch system may reduce handling, stability and braking performance and could result in an accident. • Weight distributing systems may not be compatible with surge brake couplers. Consult with your hitch and trailer manufacturer or a reputable Recreational Vehicle dealer for additional information.
540 STARTING AND OPERATING EXAMPLE — With Weight-Distributing Hitch (Correct) EXAMPLE — Improper Adjustment of WeightDistributing Hitch (Incorrect) Fifth-Wheel Hitch The fifth-wheel hitch is a special high platform with a coupling that mounts over the rear axle of the tow vehicle in the truck bed. It connects a vehicle and fifth-wheel trailer with a coupling king pin.
STARTING AND OPERATING 541 Gooseneck Hitch The gooseneck hitch employs a pivoted coupling arm which attaches to a ball mounted in the bed of a pickup truck. The coupling arm connects to the hitch mounted over the rear axle in the truck bed. Trailer Hitch Type and Maximum Trailer Weight The following chart provides the maximum trailer weight a given factory equipped trailer hitch type can tow and should be used to assist you in selecting the correct trailer hitch for your intended towing condition.
542 STARTING AND OPERATING Trailer Towing Weights (Maximum Trailer Weight Ratings) The rear bumper is intended to tow trailers up to a 5,000 lbs (2 268 kg) without added equipment or alterations to the standard equipment. Ram 1500 4x2 3.6L V-6 8–Speed Automatic Transmission 4.
STARTING AND OPERATING 543 5.7L HEMI® V-8 6–Speed Automatic Transmission ST Standard Towing: 5,000 lbs (2 268 kg) Max Towing: 10,450 lbs (4 740 kg) Max Payload: 1,710 lbs (775 kg) SLT/Outdoorsman Standard Towing: 5,000 lbs (2 268 kg) Max Towing: 10,450 lbs (4 740 kg) Max Payload: 1,690 lbs (766 kg) Sport/Laramie Standard Towing: 5,000 lbs (2 268 kg) Max Towing: 10,300 lbs (4 672 kg) Max Payload: 1,550 lbs (703 kg) 5 Ram 1500 4x4 3.
544 STARTING AND OPERATING 4.7L V-8 6–Speed Automatic Transmission 5.
STARTING AND OPERATING 545 Ram 2500 And 3500 5.7L HEMI® V-8 6–Speed Automatic Transmission ST Max Towing: 10,100 lbs (4 581 kg) Max Payload: 1,780 lbs (807 kg) SLT/Outdoorsman/Sport Max Towing: 12,300 lbs (5 579 kg) Max Payload: 3,120 lbs (1 415 kg) Laramie – NOTE: For additional trailer towing information (maxi- Trailer And Tongue Weight mum trailer weight ratings) refer to the following website Always load a trailer with 60% to 65% of the weight in addresses: the front of the trailer.
546 STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options or dealer-installed options must be considered as part of the total load on your vehicle. Refer to “Tire Safety Information/Tire and Loading Information Placard” in “Starting and Operating” for further information.
STARTING AND OPERATING 547 CAUTION! (Continued) WARNING! (Continued) • Then, during the first 500 miles (805 km) that a trailer is towed, do not drive over 50 mph (80 km/h) and do not make starts at full throttle. This helps the engine and other parts of the vehicle wear in at the heavier loads. Improper towing can lead to a collision. Follow these guidelines to make your trailer towing as safe as possible: • Make certain that the load is secured in the trailer and will not shift during travel.
548 STARTING AND OPERATING WARNING! (Continued) • GCWR must not be exceeded. • Total weight must be distributed between the tow vehicle and the trailer such that the following four ratings are not exceeded: 1. GVWR 2. GTW 3. GAWR 4. Trailer tongue weight rating for the trailer hitch utilized . • Proper tire inflation pressures are essential to the safe and satisfactory operation of your vehicle. Refer to “Tires – General Information” in “Starting and Operating” for proper tire inflation procedures.
STARTING AND OPERATING 549 Towing Requirements – Trailer Brakes • Do not interconnect the hydraulic brake system or vacuum system of your vehicle with that of the trailer. This could cause inadequate braking and possible personal injury. • An electronically actuated trailer brake controller is required when towing a trailer with electronically actuated brakes. When towing a trailer equipped with a hydraulic surge actuated brake system, an electronic brake controller is not required.
550 STARTING AND OPERATING Integrated Trailer Brake Module – If Equipped Your vehicle may have an Integrated Trailer Brake Module (ITBM) for Electric and Electric Over Hydraulic (EOH) trailer brakes. NOTE: This module has been designed and verified with electric trailer brakes and new electric over hydraulic systems. Some previous EOH systems may not be compatible with ITBM.
STARTING AND OPERATING 551 The user interface consists of the following: Manual Brake Control Lever Slide the manual brake control lever to the right to activate power to the trailer’s electric brakes independent of the tow vehicle’s brakes. If the manual brake control lever is activated while the brake is also applied, the greater of the two inputs determines the power sent to the trailer brakes.
552 STARTING AND OPERATING Adjusting GAIN 4. Press the UP or DOWN button on the steering wheel until “VEHICLE SETTINGS” appears on the screen. NOTE: This should only be performed in a traffic free environment at speeds of approximately 20–25 mph 5. Press the RIGHT arrow on the steering wheel to enter (30–40 km/h). “VEHICLE SETTINGS”. 1. Make sure the trailer brakes are in good working 6.
STARTING AND OPERATING 553 9. If the trailer wheels lockup (indicated by squealing * The suggested selection depends and may change tires), reduce the GAIN setting; if the trailer wheels depending on the customer preferences for braking perturn freely, increase the GAIN setting. formance. Condition of the trailer brakes, driving and road state may also affect the selection. Repeat Steps 8 and 9 until the GAIN setting is at a point just below trailer wheel lockup.
554 STARTING AND OPERATING CAUTION! Connecting a trailer that is not compatible with the ITBM system may result in reduced or complete loss of trailer braking. There may be a increase in stopping distance or trailer instability which could result in damage to your vehicle, trailer, or other property. WARNING! Connecting a trailer that is not compatible with the ITBM system may result in reduced or complete loss of trailer braking.
STARTING AND OPERATING 555 NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations.
556 STARTING AND OPERATING Towing Tips Before setting out on a trip, practice turning, stopping and backing the trailer up in an area away from heavy traffic. Automatic Transmission Seven-Pin Connector 1 2 3 4 — — — — Battery Backup Lamps Right Stop/Turn Electric Brakes 5 — Ground 6 — Left Stop/Turn 7 — Running Lamps The “DRIVE” range can be selected when towing. The transmission controls include a drive strategy to avoid frequent shifting when towing.
STARTING AND OPERATING 557 When towing a loaded trailer up steep grades at low Electronic Speed Control – If Equipped speeds (20 mph [32 km/h] or below), holding your • Do not use in hilly terrain or with heavy loads. vehicle in first gear (using the ERS switches) can help to • When using the speed control, if you experience speed avoid transmission overheating.
558 STARTING AND OPERATING Air Conditioning Turn off temporarily. Air Suspension System To aid in attaching/detaching the trailer from the vehicle, the air suspension system can be used. Refer to “Air Suspension System” in “Starting and Operating” for further information. NOTE: The vehicle must remain in the engine running position while attaching a trailer for proper leveling of the air suspension system.
STARTING AND OPERATING 559 WARNING! (Continued) WARNING! Do not expect that the airbag will perform as described earlier in this manual. Attaching a snowplow to this vehicle could adversely affect performance of the airbag system in a collision. Do not expect that the airbag will perform as described earlier in this manual. 2500/3500 Models Only Snowplow Prep Packages are available as a factory installed option. These packages include components necessary to equip your vehicle with a snowplow.
560 STARTING AND OPERATING • Check the runners and cutting edge for excessive wear. The loaded vehicle weight, including the snowplow system, The cutting edge should be 1/4 to 1/2 in (6 cm to 1.2 cm) all aftermarket accessories, driver, passengers, options, and above ground in snow plowing position. cargo, must not exceed either the Gross Vehicle Weight • Check that snowplow lighting is connected and func- (GVWR) or Gross Axle Weight (GAWR) ratings.
STARTING AND OPERATING 561 Over The Road Operation With Snowplow Attached The blade restricts air flow to the radiator and causes the engine to operate at higher than normal temperatures. Therefore, when transporting the plow, angle the blade completely and position it as low as road or surface conditions permit. Do not exceed 40 mph (64 km/h). The operator should always maintain a safe stopping distance and allow adequate passing clearance.
562 STARTING AND OPERATING RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.
STARTING AND OPERATING 563 NOTE: Vehicles equipped with air suspension must be lowered to the “Entry/Exit” (lowest) level, and have automatic leveling disabled, before tying them down (from the body) on a trailer or flatbed truck. Refer to “Air Suspension – If Equipped” for more information. If the vehicle cannot be lowered to the “Entry/Exit” level (for example, engine will not run), tie-downs must be fastened to the axles (not to the body).
564 STARTING AND OPERATING CAUTION! CAUTION! • Towing with the rear wheels on the ground will cause severe transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty. • Do not disconnect the driveshaft because fluid may leak from the transmission, causing damage to internal parts. • Front or rear wheel lifts must not be used. Internal damage to the transmission or transfer case will occur if a front or rear wheel lift is used when recreational towing.
STARTING AND OPERATING 565 CAUTION! (Continued) • Towing this vehicle in violation of the above requirements can cause severe transmission and/or transfer case damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case, causing damage to internal parts. • Do not use a bumper-mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged.
566 STARTING AND OPERATING 1. Bring the vehicle to a complete stop, with the engine running. Firmly apply the parking brake. 2. Shift the transmission to NEUTRAL. 3. Press and hold the brake pedal. 4. Depress the clutch pedal on a manual transmission. shift to NEUTRAL (N) is complete. After the shift is completed and the NEUTRAL (N) light stays on, release the NEUTRAL (N) button. 6. Release the parking brake. 7. Shift the transmission into REVERSE. 8.
STARTING AND OPERATING 567 11. Shift the transmission into PARK or place manual transmission in gear (NOT in Neutral). On 8-speed transmissions the shifter will automatically select PARK when the engine is turned off. met during the shift, the NEUTRAL (N) indicator light will flash continuously until all requirements are met or until the NEUTRAL (N) button is released. 12.
568 STARTING AND OPERATING 3. Press and hold the brake pedal. 4. Start the engine. Shift the transmission into NEUTRAL. Depress the clutch pedal on a manual transmission. • With manual shift transfer case, shift the transfer case lever to the desired position. • With electronic shift transfer case with rotary selector switch, press and hold the transfer case NEUTRAL (N) button until the NEUTRAL (N) indicator light turns off. After the NEUTRAL (N) indicator light turns off, release the NEUTRAL (N) button.
STARTING AND OPERATING 569 • The ignition switch must be in the ON/RUN position for a shift to take place and for the position indicator 10. Release the parking brake. lights to be operable. If the ignition switch is not in the ON/RUN position, the shift will not take place and no 11. Shift the transmission into gear, release the brake position indicator lights will be on or flashing. pedal (and clutch pedal on manual transmissions), and check that the vehicle operates normally.
WHAT TO DO IN EMERGENCIES CONTENTS 䡵 HAZARD WARNING FLASHERS . . . . . . . . . . .573 ▫ Reinstalling The Jack And Tools (1500 Series) . .590 䡵 IF YOUR ENGINE OVERHEATS . . . . . . . . . . . .573 ▫ Hub Caps/Wheel Covers — If Equipped . . . .593 䡵 JACKING AND TIRE CHANGING 1500 SERIES TRUCKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . .574 ▫ Wheel Nuts . . . . . . . . . . . . . . . . . . . . . . . . .594 ▫ Removal Of Jack And Tools (1500 Series) . . . . .575 ▫ Jack Location. . . . . . . . .
572 WHAT TO DO IN EMERGENCIES ▫ Jack Instructions (2500, 3500 Series) . . . . . . . . .601 䡵 FREEING A STUCK VEHICLE . . . . . . . . . . . . .619 ▫ To Stow The Flat Or Spare . . . . . . . . . . . . . . .607 䡵 EMERGENCY TOW HOOKS — IF EQUIPPED . .621 ▫ Reinstalling The Jack And Tools 䡵 SHIFT LEVER OVERRIDE . . . . . . . . . . (2500 And 3500 Series) . . . . . . . . . . . . . . . . . .609 ▫ Column Shifter — If Equipped . . . . . . ▫ Hub Caps/Wheel Covers — If Equipped . . . .
WHAT TO DO IN EMERGENCIES 573 HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the upper switch bank just below the radio. potential for overheating by taking the appropriate action. Press the switch to turn on the Hazard Warning • On the highways — slow down. flasher.
574 WHAT TO DO IN EMERGENCIES CAUTION! Driving with a hot cooling system could damage your vehicle. If the temperature gauge reads HOT (H), pull over and stop the vehicle. Idle the vehicle with the air conditioner turned off until the pointer drops back into the normal range. If the pointer remains on HOT (H), and you hear continuous chimes, turn the engine off immediately and call for service. WARNING! You or others can be badly burned by hot engine coolant (antifreeze) or steam from your radiator.
WHAT TO DO IN EMERGENCIES 575 WARNING! (Continued) • The jack is designed to be used as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes. The vehicle should be jacked on a firm level surface only. Avoid ice or slippery areas. NOTE: To assist with changing a spare tire, the air suspension system has a feature which allows the automatic leveling to be disabled.
576 WHAT TO DO IN EMERGENCIES Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then slide the assembly out from under the seat.
WHAT TO DO IN EMERGENCIES 577 Release the tool bag straps from the jack and remove tools from bag. WARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid acceleration or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.
578 WHAT TO DO IN EMERGENCIES 2. Rotate the wheel wrench handle counterclockwise until the spare tire is on the ground with enough cable 1. Remove the spare tire before attempting to jack up the slack to allow you to pull it out from under the vehicle. truck. Attach the wheel wrench to the jack extension tube with the curved angle facing away from the vehicle. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube.
WHAT TO DO IN EMERGENCIES 579 3. Pull the spare tire out from under the vehicle to gain access to the spare tire retainer. 4. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable.
580 WHAT TO DO IN EMERGENCIES 5. Pull the retainer through the center of the wheel. Preparations 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 2. Turn on the Hazard Warning flasher. 3. Set the parking brake.
WHAT TO DO IN EMERGENCIES 581 5. Turn the ignition OFF. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked.
582 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway, be extremely careful of motor traffic.
WHAT TO DO IN EMERGENCIES 583 1. Remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. 3. Placement of the jack: 4x2 Series Trucks Front Jacking Location There is a jack location indicator on the rear portion of the lower control arm.
584 WHAT TO DO IN EMERGENCIES When changing a front wheel, place the scissor jack 4x4 Series Trucks Front Jacking Location under the rear portion of the lower control arm as shown There is a jack location indicator on the rear portion of the below. lower control arm.
WHAT TO DO IN EMERGENCIES 585 When changing a front wheel, place the scissor jack 4x2 and 4x4 Rear Jacking Location under the rear portion of the lower control arm as shown Operate the jack using the jack drive tube and the wheel below. wrench. The tube extension may be used but is not required. For 4x2 and 4x4 trucks, when changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube.
586 WHAT TO DO IN EMERGENCIES CAUTION! Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. 4. By rotating the lug wrench clockwise, raise the vehicle until the wheel just clears the surface. WARNING! Rear Jacking Location Connect the jack tube extension and wheel wrench. Raising the vehicle higher than necessary can make the vehicle unstable and cause a collision.
WHAT TO DO IN EMERGENCIES 587 5. Remove the wheel nuts and pull the wheel off. Install the 7. Install the wheel center cap and remove the wheel spare wheel and wheel nuts with the cone shaped end of blocks. Do not install chrome or aluminum wheel the wheel nuts toward the wheel. To avoid the risk of center caps on the spare wheel. This may result in cap forcing the vehicle off the jack, do not fully tighten the damage. wheel nuts until the vehicle has been lowered. 8.
588 WHAT TO DO IN EMERGENCIES 1. Turn the wheel so that the valve stem is facing the ground and toward the rear of the vehicle for conveNOTE: Vehicles equipped with aluminum wheels cannience in checking the spare tire inflation. Slide the not be stored under the vehicle because the wheel wheel retainer through the center of the wheel. retainer will not fit through the wheel pilot hole. Secure the flat tire in the bed of the truck. Have the flat tire repaired or replaced immediately.
WHAT TO DO IN EMERGENCIES 589 2. Lift the spare tire with one hand to give clearance to 3. Attach the wheel wrench to the jack extension tube tilt the retainer at the end of the cable and position it with the curved angle facing away from the vehicle. properly across the wheel opening. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube.
590 WHAT TO DO IN EMERGENCIES 4. Rotate the lug wrench handle clockwise until the wheel is drawn into place against the underside of the vehicle. Continue to rotate until you feel the winch mechanism slip, or click three or four times. It cannot be overtightened. Push against the tire several times to ensure it is firmly in place. NOTE: The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch.
WHAT TO DO IN EMERGENCIES 591 2. Position the jack and tool bag. Make sure the lug 3. Secure the tool bag straps to the jack. wrench is under the jack near the jack turn-screw.
592 WHAT TO DO IN EMERGENCIES 4. Place the jack and tools in the storage position holding 5. Turn the wing bolt clockwise to secure to the floor pan. the jack by the jack turn-screw, slip the jack and tools Reinstall the plastic cover. under the seat so that the bottom slot engages into the fastener on the floor. Jack And Tools (1500 Series) Jack Hold Down Fastener NOTE: Ensure that the jack slides into the front hold down location.
WHAT TO DO IN EMERGENCIES 593 WARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid acceleration or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury. Hub Caps/Wheel Covers — If Equipped The hub caps must be removed before raising the vehicle off the ground. CAUTION! Use a back-and-forth motion to remove the hub cap.
594 WHAT TO DO IN EMERGENCIES Wheel Nuts All wheel nuts should be tightened occasionally to eliminate the possibility of wheel studs being sheared or the bolt holes in the wheels becoming elongated. This is especially important during the first few hundred miles/kilometers of operation to allow the wheel nuts to become properly set. All wheel nuts should first be firmly seated against the wheel. The wheel nuts should then be tightened to recommended torque.
WHAT TO DO IN EMERGENCIES 595 JACKING AND TIRE CHANGING 2500 AND 3500 SERIES TRUCKS WARNING! • Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • Being under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never put any part of your body under a vehicle that is on a jack.
596 WHAT TO DO IN EMERGENCIES Remove the jack and tools by turning the wing bolt counterclockwise, remove the wing bolt and then slide the assembly out from under the seat.
WHAT TO DO IN EMERGENCIES 597 Remove the jack and tools from the bracket assembly. Turn the jack-turn-screw counterclockwise to release jack from bracket assembly. WARNING! After using the jack and tools, always reinstall them in the original carrier and location. While driving you may experience abrupt stopping, rapid acceleration or sharp turns. A loose jack, tools, bracket or other objects in the vehicle may move around with force, resulting in serious injury.
598 WHAT TO DO IN EMERGENCIES 2. Rotate the wheel wrench handle counterclockwise until the spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle.
WHAT TO DO IN EMERGENCIES 599 3. Pull the spare tire out from under the vehicle to gain access to the spare tire retainer. 4. Lift the spare tire with one hand to give clearance to tilt the retainer at the end of the cable.
600 WHAT TO DO IN EMERGENCIES 5. Pull the retainer through the center of the wheel. Preparations 1. Park the vehicle on a firm, level surface. Avoid ice or slippery areas. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic, pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. 2. Turn on the Hazard Warning flasher. 3. Set the parking brake.
WHAT TO DO IN EMERGENCIES 601 5. Turn the ignition OFF. Block both the front and rear of the wheel diagonally opposite the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. NOTE: Passengers should not remain in the vehicle when the vehicle is being jacked.
602 WHAT TO DO IN EMERGENCIES WARNING! (Continued) • Do not let anyone sit in the vehicle when it is on a jack. • Do not get under the vehicle when it is on a jack. If you need to get under a raised vehicle, take it to a service center where it can be raised on a lift. • Only use the jack in the positions indicated and for lifting this vehicle during a tire change. • If working on or near a roadway, be extremely careful of motor traffic.
WHAT TO DO IN EMERGENCIES 603 1. Remove the spare wheel, jack, and tools from storage. 2. Using the lug wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. 3. Placement of the jack: 4x2 Series Trucks Front Jacking Location For 2500 and 3500 4x2 series trucks, when changing a front wheel, place the bottle jack under the frame rail behind the wheel. Locate the jack as far forward as possible on the straight part of the frame.
604 WHAT TO DO IN EMERGENCIES 4x4 Series Trucks Front Jacking Location For 2500 and 3500 4x4 series trucks, when changing the front wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube. Place the jack under the axle as close to the tire as possible with the drive tubes extending to the front. Connect the jack tube extension and wheel wrench.
WHAT TO DO IN EMERGENCIES 605 NOTE: If the bottle jack will not lower by turning the dial (thumbwheel) by hand, it may be necessary to use the jack drive tube in order to lower the jack. 4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface. WARNING! Rear Jacking Location (All) Connect the jack tube extension and wheel wrench.
606 WHAT TO DO IN EMERGENCIES avoid the risk of forcing the vehicle off the jack, do not 7. Install the wheel center cap and remove the wheel fully tighten the wheel nuts until the vehicle has been blocks. Do not install chrome or aluminum wheel lowered. center caps on the spare wheel. This may result in cap damage. 6. Using the lug wrench, finish tightening the wheel nuts using a crisscross pattern. The correct wheel nut 8. Lower the jack to its fully closed position.
WHAT TO DO IN EMERGENCIES 607 1. Turn the wheel so that the valve stem is facing the ground and toward the rear of the vehicle for conveNOTE: Have the flat tire repaired or replaced immedinience in checking the spare tire inflation. Slide the ately. wheel retainer through the center of the wheel. To Stow The Flat Or Spare WARNING! A loose tire thrown forward in a collision or hard stop could injure the occupants in the vehicle. Have the deflated (flat) tire repaired or replaced immediately.
608 WHAT TO DO IN EMERGENCIES 2. Lift the spare tire with one hand to give clearance to 3. Attach the wheel wrench to the jack extension tube tilt the retainer at the end of the cable and position it with the curved angle facing away from the vehicle. properly across the wheel opening. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube.
WHAT TO DO IN EMERGENCIES 609 4. Rotate the lug wrench handle clockwise until the wheel is drawn into place against the underside of the vehicle. Continue to rotate until you feel the winch mechanism slip, or click three or four times. It cannot be overtightened. Push against the tire several times to ensure it is firmly in place. NOTE: The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch.
610 WHAT TO DO IN EMERGENCIES 3. Place the jack and tool bracket assembly in the storage position holding the jack by the jack turn-screw, slip the jack and tools under the seat so that the bottom slot engages into the fastener on the floor. Jack And Tools Bracket Assembly Jack Hold Down Fastener NOTE: Ensure that the jack and tool bracket assembly slides into the front hold down location.
WHAT TO DO IN EMERGENCIES 611 4. Turn the wing bolt clockwise to secure to the floor pan. Hub Caps/Wheel Covers — If Equipped Reinstall the plastic cover. The hub caps must be removed before raising the vehicle off the ground. CAUTION! Use extreme caution when removing the front and rear center caps. Damage can occur to the center cap and/or the wheel if screwdriver type tools are used. A pulling motion, not a pry off motion, is recommended to remove the caps.
612 WHAT TO DO IN EMERGENCIES rear hub caps. Position the hook and pull out on the ratchet firmly. The hub cap should pop off. The wheel skins can now be removed. For the front hub cap on models use the blade on the end of the lug wrench to pry the caps off. The wheel skin can now be removed. CAUTION! Replace the wheel skins first using a rubber mallet. When replacing the hub caps, tilt the cap retainer over the lug nut bolt circle and strike the high side down with a rubber mallet.
WHAT TO DO IN EMERGENCIES 613 Type Nut Stud Size Hex Size Torque Ft Lbs Cone Flanged M14 x 1.5 M14 x 1.5 22 mm 22 mm 120-140 130-160 Torque Newton Meters 160-190 175-215 8-Stud — Dual Rear Wheels Dual wheels are flat-mounted and center-piloted. The lug nuts are a two-piece assembly. When the tires are being rotated or replaced, clean these lug nuts and add two drops of oil at the interface between the hex and the washer.
614 WHAT TO DO IN EMERGENCIES Slots in the wheels will assist in properly orienting the These dual rear wheels should be tightened as follows: inner and outer wheels. Align these slots when assembling the wheels for best access to the tire valve on the inner wheel. The tires of both dual wheels must be completely off the ground when tightening, to ensure wheel centering and maximum wheel clamping.
WHAT TO DO IN EMERGENCIES 615 second time to verify that specific torque has been JUMP-STARTING PROCEDURES achieved. Retighten to specifications at 100 miles If your vehicle has a discharged battery it can be jump(160 km) and after 500 miles (800 km). started using a set of jumper cables and a battery in It is recommended that wheel stud nuts be kept torqued another vehicle or by using a portable battery booster to specifications at all times. Torque wheel stud nuts to pack.
616 WHAT TO DO IN EMERGENCIES WARNING! Do not attempt jump-starting if the battery is frozen. It could rupture or explode and cause personal injury. Preparations For Jump-Start The battery in your vehicle is located in the front of the engine compartment, behind the left headlight assembly. NOTE: The positive battery post is covered with a protective cap. Lift up on the cap to gain access to the positive battery post.
WHAT TO DO IN EMERGENCIES 617 WARNING! • Take care to avoid the radiator cooling fan whenever the hood is raised. It can start anytime the ignition switch is ON. You can be injured by moving fan blades. • Remove any metal jewelry such as rings, watch bands and bracelets that could make an inadvertent electrical contact. You could be seriously injured. • Batteries contain sulfuric acid that can burn your skin or eyes and generate hydrogen gas which is flammable and explosive.
618 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Failure to follow these procedures could result in damage to the charging system of the booster vehicle or the discharged vehicle. Do not connect the cable to the negative post (-) of the discharged battery. The resulting electrical spark could cause the battery to explode and could result in personal injury. 1. Connect the positive (+) end of the jumper cable to the positive (+) post of the discharged vehicle. 5.
WHAT TO DO IN EMERGENCIES 619 8. Disconnect the opposite end of the positive (+) jumper FREEING A STUCK VEHICLE cable from the positive (+) post of the booster battery. If your vehicle becomes stuck in mud, sand, or snow, it 9. Disconnect the positive (+)end of the jumper cable can often be moved using a rocking motion. Turn the steering wheel right and left to clear the area around the from the positive (+) post of the discharged vehicle. front wheels.
620 WHAT TO DO IN EMERGENCIES CAUTION! CAUTION! Racing the engine or spinning the wheels may lead to transmission overheating and failure. Allow the engine to idle with the transmission in NEUTRAL for at least one minute after every five rocking-motion cycles. This will minimize overheating and reduce the risk of transmission failure during prolonged efforts to free a stuck vehicle.
WHAT TO DO IN EMERGENCIES 621 WARNING! (Continued) WARNING! explode and injure someone. Do not spin your vehicle’s wheels faster than 30 mph (48 km/h) or for longer than 30 seconds continuously without stopping when you are stuck and do not let anyone near a spinning wheel, no matter what the speed. • Do not use a chain for freeing a stuck vehicle. Chains may break, causing serious injury or death. • Stand clear of vehicles when pulling with tow hooks.
622 WHAT TO DO IN EMERGENCIES SHIFT LEVER OVERRIDE If a malfunction occurs and the shift lever cannot be moved out of the PARK position, you can use one of the following procedures to temporarily move the shift lever: Column Shifter — If Equipped 1. Turn the engine off. 2. Firmly apply the parking brake. 3. Tilt the steering wheel to the full up position. 4. Press and maintain firm pressure on the brake pedal. Shift Lever Override Access Port 5.
WHAT TO DO IN EMERGENCIES 623 Center Console Shifter — If Equipped 1. Turn the engine off. 2. Firmly apply the parking brake. 3. Using a small screwdriver or similar tool, remove the shift lever override access cover (located to the right of the shift lever). 4. Press and maintain firm pressure on the brake pedal. 5. Insert the screwdriver or similar tool into the access hole, and push and hold the override release lever down. 6 Shift Lever Override Access Cover 6.
624 WHAT TO DO IN EMERGENCIES MANUAL PARK RELEASE — 8 SPEED TRANSMISSION (3.6L Engine) WARNING! Always secure your vehicle by fully applying the parking brake, before activating the Manual Park Release. Activating the Manual Park Release will allow your vehicle to roll away if it is not secured by the parking brake or by proper connection to a tow vehicle. Activating the Manual Park Release on an unsecured vehicle could lead to serious injury or death for those in or around the vehicle.
WHAT TO DO IN EMERGENCIES 625 2. Using a small screwdriver or similar tool, remove the To Reset The Manual Park Release: Manual Park Release access cover, which is just above 1. Push the locking tab to the right, to unlock the lever. the parking brake release handle, below and to the left 2. Rotate the Manual Park Release lever forward to its of the steering column. original position, until the locking tab snaps into place 3. Using the screwdriver or similar tool, push the to secure the lever.
626 WHAT TO DO IN EMERGENCIES NOTE: Vehicles equipped with air suspension must be This section describes procedures for towing a disabled lowered to the Park (lowest) level, and have automatic vehicle using a commercial wrecker service. If the trans- leveling disabled, before tying them down (from the body) on a trailer or flatbed truck.
WHAT TO DO IN EMERGENCIES 627 Towing Condition Flat Tow Wheel Lift or Dolly Tow Flatbed Wheels OFF the Ground NONE 2WD Models 4WD Models If transmission is operable: • Transmission in NEUTRAL • 30 mph (48 km/h) max speed • 15 miles (24 km) max distance (6–speed transmission) • 30 miles (48 km) max distance (8–speed transmission) Front Rear OK See instructions in “Recreational Towing” under “Starting and Operating” • Auto Transmission in PARK • Manual Transmission in gear ( NOT NEUTRAL) • Transfer C
628 WHAT TO DO IN EMERGENCIES If you must use the accessories (wipers, defrosters, etc.) If flatbed equipment is not available, and the transmiswhile being towed, the ignition must be in the ON/RUN sion is operable, the vehicle may be towed (with rear wheels on the ground) under the following conditions: position, not the ACC position. If the key fob is unavailable or the vehicle’s battery is • The transmission must be in NEUTRAL.
WHAT TO DO IN EMERGENCIES 629 CAUTION! Towing this vehicle in violation of the above requirements can cause severe engine and/or transmission damage. Damage from improper towing is not covered under the New Vehicle Limited Warranty. Four-Wheel Drive Models The manufacturer recommends towing with all wheels OFF the ground. Acceptable methods are to tow the vehicle on a flatbed or with one end of vehicle raised and the opposite end on a towing dolly.
MAINTAINING YOUR VEHICLE CONTENTS 䡵 ENGINE COMPARTMENT — 3.6L . . . . . . . . . .634 ▫ Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . .641 䡵 ENGINE COMPARTMENT — 4.7L . . . . . . . . . .635 ▫ Engine Oil Filter . . . . . . . . . . . . . . . . . . . . . .644 䡵 ENGINE COMPARTMENT — 5.7L . . . . . . . . . .636 ▫ Engine Air Cleaner Filter . . . . . . . . . . . . . . . .644 䡵 ONBOARD DIAGNOSTIC SYSTEM (OBD II) . . .637 ▫ Maintenance-Free Battery . . . . . . . . . . . . . . .
632 MAINTAINING YOUR VEHICLE ▫ Adding Washer Fluid . . . . . . . . . . . . . . . . . .648 䡵 BULB REPLACEMENT . . . . . . . . . . . . . . . . . .685 ▫ Exhaust System . . . . . . . . . . . . . . . . . . . . . .649 ▫ Cooling System . . . . . . . . . . . . . . . . . . . . . .651 ▫ Brake System . . . . . . . . . . . . . . . . . . . . . . . .658 ▫ Rear Axle And 4x4 Front Driving Axle Fluid Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .660 ▫ Transfer Case . . . . . . . . . . . . . . . . . . . .
MAINTAINING YOUR VEHICLE 633 䡵 FLUIDS, LUBRICANTS AND GENUINE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .696 ▫ Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . .696 ▫ Chassis . . . . . . . . . . . . . . . . . . . . . . . . . . . .
634 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 3.
MAINTAINING YOUR VEHICLE 635 ENGINE COMPARTMENT — 4.
636 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT — 5.
MAINTAINING YOUR VEHICLE 637 ONBOARD DIAGNOSTIC SYSTEM (OBD II) Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
638 MAINTAINING YOUR VEHICLE “Understanding Your Instrument Panel” for further information. Tighten the fuel filler cap properly and press the SELECT button to turn off the message. If the problem continues, the message will appear the next time the vehicle is started. Normally, the OBD II system will be ready. The OBD II system may not be ready if your vehicle was recently serviced, recently had a dead battery or a battery replacement.
MAINTAINING YOUR VEHICLE 639 4. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced • The MIL will flash for about 10 seconds and then before going to the I/M station. The I/M station can fail return to being fully illuminated until you turn OFF your vehicle because the MIL is on with the engine the ignition or start the engine.
640 MAINTAINING YOUR VEHICLE DEALER SERVICE MAINTENANCE PROCEDURES Your authorized dealer has the qualified service personnel, special tools, and equipment to perform all service operations in an expert manner. Service Manuals are available which include detailed service information for your vehicle. Refer to these Service Manuals before attempting any procedure yourself. The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle.
MAINTAINING YOUR VEHICLE 641 CAUTION! (Continued) • Your vehicle has been built with improved fluids that protect the performance and durability of your vehicle and also allow extended maintenance intervals. Do not use chemical flushes in these components as the chemicals can damage your engine, transmission, power steering or air conditioning. Such damage is not covered by the New Vehicle Limited Warranty.
642 MAINTAINING YOUR VEHICLE Change Engine Oil American Petroleum Institute (API) Engine Oil The oil change indicator system will remind you that it is Identification Symbol time to take your vehicle in for scheduled maintenance. This symbol means that the oil has Refer to the “Maintenance Schedule” for further informabeen certified by the American tion. Petroleum Institute (API).
MAINTAINING YOUR VEHICLE 643 NOTE: For 2500/3500 trucks with a 5.7L engine operating under a gross combined weight rating of 14,000 lbs (6 SAE 5W-20 engine oil is recommended for all operating 350 kg) or greater, SAE 5W-30 engine oil is recommended temperatures. This engine oil improves low temperature for all operating temperatures. starting and vehicle fuel economy. The engine oil filler cap also shows the recommended engine oil viscosity for Synthetic Engine Oils your engine.
644 MAINTAINING YOUR VEHICLE Engine Oil Filter The engine oil filter should be replaced with a new filter at every engine oil change. Engine Oil Filter Selection This manufacturer’s engines have a full-flow type oil filter. Use a filter of this type for replacement. The quality of replacement filters varies considerably. Only high quality filters should be used to assure most efficient service. MOPAR® engine oil filters are a high quality oil filter and are recommended.
MAINTAINING YOUR VEHICLE 645 Maintenance-Free Battery WARNING! (Continued) Your vehicle is equipped with a maintenance-free battery. You will never have to add water, nor is periodic maintenance required. WARNING! • Battery fluid is a corrosive acid solution and can burn or even blind you. Do not allow battery fluid to contact your eyes, skin, or clothing. Do not lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water.
646 MAINTAINING YOUR VEHICLE CAUTION! (Continued) CAUTION! • If a “fast charger” is used while the battery is in the vehicle, disconnect both vehicle battery cables before connecting the charger to the battery. Do not use a “fast charger” to provide starting voltage. Do not use chemical flushes in your air conditioning system as the chemicals can damage your air conditioning components. Such damage is not covered by the New Vehicle Limited Warranty.
MAINTAINING YOUR VEHICLE 647 WARNING! (Continued) • The air conditioning system contains refrigerant under high pressure. To avoid risk of personal injury or damage to the system, adding refrigerant or any repair requiring lines to be disconnected should be done by an experienced technician. Refrigerant Recovery And Recycling Front Driveshaft Lubrication – 2500/3500 (Four-Wheel Drive) Models (Ram Trucks Only) Lubricate the front driveshaft grease fitting at each oil change.
648 MAINTAINING YOUR VEHICLE underhood services, the hood latch, release mechanism Avoid using the wiper blades to remove frost or ice from the windshield. Keep the blade rubber out of contact with and safety catch should be cleaned and lubricated. petroleum products such as engine oil, gasoline, etc. The external lock cylinders should be lubricated twice a year, preferably in the Fall and Spring.
MAINTAINING YOUR VEHICLE 649 To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
650 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Safety Tips/Exhaust Gas” in “Things To Know Before Starting Your Vehicle” for further information. • A hot exhaust system can start a fire if you park over materials that can burn.
MAINTAINING YOUR VEHICLE 651 Under normal operating conditions, the catalytic con- • Do not try to start the engine by pushing or towing the vehicle. verter will not require maintenance. However, it is important to keep the engine properly tuned to assure • Do not idle the engine with any spark plug wires proper catalyst operation and prevent possible catalyst disconnected or removed, such as when diagnostic damage.
652 MAINTAINING YOUR VEHICLE Engine Coolant Checks With the engine at normal operating temperature (but not running), check the cooling system pressure cap for proper vacuum sealing by draining a small amount of engine coolant (antifreeze) from the radiator drain cock. The radiator drain cock is located in the lower radiator tank. If the cap is sealing properly, the engine coolant (antifreeze) will begin to drain from the coolant expansion bottle.
MAINTAINING YOUR VEHICLE 653 Selection Of Coolant CAUTION! (Continued) Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. CAUTION! • Mixing of engine coolant (antifreeze) other than specified Organic Additive Technology (OAT) engine coolant (antifreeze), may result in engine damage and may decrease corrosion protection.
654 MAINTAINING YOUR VEHICLE miles (240,000 km) before replacement. To prevent reduc- • Use only high purity water such as distilled or deioning this extended maintenance period, it is important that ized water when mixing the water/engine coolant (antifreeze) solution. The use of lower quality water you use the same engine coolant (OAT coolant conformwill reduce the amount of corrosion protection in the ing to MS-12106) throughout the life of your vehicle. engine cooling system.
MAINTAINING YOUR VEHICLE 655 Cooling System Pressure Cap WARNING! (Continued) The cap must be fully tightened to prevent loss of engine coolant (antifreeze), and to ensure that the engine coolant (antifreeze) will return to the radiator from the coolant expansion bottle. • Do not use a pressure cap other than the one specified for your vehicle. Personal injury or engine damage may result.
656 MAINTAINING YOUR VEHICLE 2. Lift and remove the plastic dipstick from the reservoir neck. With the engine OFF and cold, the level of the engine coolant should be between the MIN and MAX range on the dipstick. Checking Coolant Level To check the coolant level: 1. Open the coolant reservoir. 3. Check the coolant level on the dipstick.
MAINTAINING YOUR VEHICLE 657 of this. As long as the engine operating temperature is • Do not overfill the coolant expansion bottle. satisfactory, the coolant bottle need only be checked once • Check the coolant freeze point in the radiator and in a month. the coolant expansion bottle.
658 MAINTAINING YOUR VEHICLE • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. • Do not change the thermostat for Summer or Winter operation. If replacement is ever necessary, install ONLY the correct type thermostat. Other designs may result in unsatisfactory engine coolant (antifreeze) performance, poor gas mileage, and increased emissions.
MAINTAINING YOUR VEHICLE 659 With disc brakes the fluid level can be expected to fall as the brake linings wear. However, an unexpected drop in fluid level may be caused by a leak and a system check should be conducted. Use only the manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. WARNING! • Use only manufacturer’s recommended brake fluid.
660 MAINTAINING YOUR VEHICLE Rear Axle And 4x4 Front Driving Axle Fluid Level Drain And Refill For normal service, periodic fluid level checks are not required. When the vehicle is serviced for other reasons the exterior surfaces of the axle assembly should be inspected. If gear oil leakage is suspected inspect the fluid level. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. This inspection should be made with the vehicle in a level position.
MAINTAINING YOUR VEHICLE 661 Limited Slip Additive should be added to the gear Fluid Level Check lubricant whenever a fluid change is made to an axle This fluid level can be checked by removing the filler equipped with a Limited Slip Differential. plug. The fluid level should be to the bottom edge of the 2500/3500 Model axles DO NOT REQUIRE any limited filler plug hole with the vehicle in a level position. slip oil additive (friction modifiers).
662 MAINTAINING YOUR VEHICLE CAUTION! CAUTION! • Using a transmission fluid other than the manufacturer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder, and will require more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for fluid specifications. Do not use chemical flushes in your transmission as the chemicals can damage your transmission components.
MAINTAINING YOUR VEHICLE 663 Use the following procedure to check the transmission 6. Remove the dipstick, wipe it clean and reinsert it until fluid level properly: seated. 1. Monitor the transmission temperature using the EVIC 7. Remove the dipstick again and note the fluid level on both sides. The fluid level reading is only valid if there display, and operate the vehicle as required to reach the normal operating temperature. is a solid coating of oil on both sides of the dipstick.
664 MAINTAINING YOUR VEHICLE NOTE: If it is necessary to check the transmission below the operating temperature, the fluid level should be between the two “COLD” (lower) holes on the dipstick with the fluid at 60-70°F / 16-21°C. Only use the COLD region of the dipstick as a rough reference when setting the fluid level after a transmission service or fluid change. Re-check the fluid level, and adjust as required, once the transmission reaches normal operating temperature.
MAINTAINING YOUR VEHICLE 665 Appearance Care And Protection From Corrosion What Causes Corrosion? Protection Of Body And Paint From Corrosion Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle. Vehicle body care requirements vary according to geographic locations and usage. Chemicals that make roads passable in snow and ice and those that are sprayed on trees and road surfaces during other seasons are highly corrosive to the metal in your vehicle.
666 MAINTAINING YOUR VEHICLE • If insects, tar, or other similar deposits have accumu- Special Care lated on your vehicle, use MOPAR® Super Kleen Bug • If you drive on salted or dusty roads or if you drive and Tar Remover to remove. near the ocean, hose off the undercarriage at least once a month. • Use a high quality cleaner wax, such as MOPAR® Cleaner Wax to remove road film, stains and to protect • It is important that the drain holes in the lower edges your paint finish.
MAINTAINING YOUR VEHICLE 667 • If you carry special cargo such as chemicals, fertilizers, control dust on dirt roads. Use a soft cloth or sponge and de-icer salt, etc., be sure that such materials are well mild soap to wipe away promptly. Do not use harsh chemicals or a stiff brush. They can damage the wheel’s packaged and sealed. protective coating that helps keep them from corroding • If a lot of driving is done on gravel roads, consider and tarnishing. mud or stone shields behind each wheel.
668 MAINTAINING YOUR VEHICLE When cleaning extremely dirty wheels including excessive brake dust, care must be taken in the selection of tire and wheel cleaning chemicals and equipment to prevent damage to the wheels. Mopar Wheel Treatment or Mopar Chrome Cleaner or their equivalent is recommended or select a non-abrasive, non-acidic cleaner for aluminum or chrome wheels. Do not use any products on Dark Vapor or Black Satin Chrome Wheels.
MAINTAINING YOUR VEHICLE 669 Stain Repel Fabric Cleaning Procedure – If Equipped Interior Care Use MOPAR® Total Clean to clean fabric upholstery and Stain Repel seats may be cleaned in the following man- carpeting. ner: Use MOPAR® Total Clean to clean vinyl upholstery. • Remove as much of the stain as possible by blotting MOPAR® Total Clean is specifically recommended for with a clean, dry towel. leather upholstery. • Blot any remaining stain with a clean, damp towel.
670 MAINTAINING YOUR VEHICLE WARNING! Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm. CAUTION! Do not use Alcohol and Alcohol-based and/or Keton based cleaning products to clean leather seats, as damage to the seat may result. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution followed by rinsing.
MAINTAINING YOUR VEHICLE 671 When cleaning the rear view mirror, spray cleaner on the If the belts need cleaning, use a mild soap solution or towel or rag that you are using. Do not spray cleaner lukewarm water. Do not remove the belts from the car to wash them. Dry with a soft cloth. directly on the mirror. Cleaning Plastic Instrument Cluster Lenses Replace the belts if they appear frayed or worn or if the buckles do not work properly.
672 MAINTAINING YOUR VEHICLE To help maintain the appearance of your Spray-On Bedliner, the manufacturer recommends you periodically rinse all loose dirt from your truck bed and clean your truck at least twice per year using the MOPAR® Spray-On Bedliner Conditioner available at your local authorized dealer. WARNING! Do not use silicon-based protection products to clean your bedliner. Silicon-based products can become slippery and may result in personal injury.
MAINTAINING YOUR VEHICLE 673 to cover the metal exposed by the scratch is required. To repair a tear or gouge, follow the directions provided in the MOPAR® Quick Repair Kit. FUSES POWER DISTRIBUTION CENTER The Power Distribution Center is located in the engine compartment near the battery. This center contains cartridge fuses, micro fuses, relays, and circuit breakers.
674 MAINTAINING YOUR VEHICLE Cavity F01 F03 F05 Cartridge Fuse 80 Amp Red 60 Amp Yellow 40 Amp Green F06 40 Amp Green F07 40 Amp Green Micro Fuse Description Cavity Rad Fan Control Module – If equipped Rad Fan – If Equipped Compressor for Air Suspension – If Equipped Antilock Brakes/ Electronic Stability Control Pump Starter Solenoid F08 F09 F10 F10 F11 Cartridge Fuse 40 Amp Green 40 Amp Green 40 Amp Green 50 Amp Red 30 Amp Pink Micro Fuse Description Emissions Diesel – If Equipped Diesel
MAINTAINING YOUR VEHICLE 675 Cavity F12 F13 F14 F15 F19 F20 Cartridge Fuse 40 Amp Green 40 Amp Green 40 Amp Green 30 Amp Pink 30 Amp Pink 30 Amp Pink Micro Fuse Description Cavity Body Controller #3 / Interior Lights Blower Motor F21 Body Controller #4 / Power Locks Electric Park Brake Right Side – If Equipped SCR – If Equipped F23 F22 F24 F25 F25 Passenger Door Module Cartridge Fuse 30 Amp Pink 20 Amp Yellow 30 Amp Pink 30 Amp Pink 30 Amp Pink 30 Amp Pink Micro Fuse Description Drive Trai
676 MAINTAINING YOUR VEHICLE Cavity F26 F28 F29 F30 F32 Cartridge Fuse 30 Amp Pink 20 Amp Yellow 20 Amp Yellow 30 Amp Pink 30 Amp Pink Micro Fuse Description Cavity Antilock Brakes/ Stability Control Module/Valves Trailer Tow Backup Lights – If Equipped Trailer Tow Parking Lights – If Equipped Trailer Tow Receptacle Drive Train Control Module – If Equipped F33 Cartridge Fuse 20 Amp Yellow F34 30 Amp Pink F35 30 Amp Pink 30 Amp Pink 30 Amp Pink F36 F37 Micro Fuse Description Diesel Fuel H
MAINTAINING YOUR VEHICLE 677 Cavity F38 F39 F41 F42 F43 F44 Cartridge Fuse 30 Amp Pink Micro Fuse 30 Amp Pink 10 Amp Red 20 Amp Yellow 10 Amp Red 10 Amp Red Description Cavity Power Inverter 115V AC– If Equipped Vehicle System Interface Module #1– If Equipped Active Grill Shutter F46 F47 F49 F50 Cartridge Fuse Micro Fuse Description 10 Amp Red 10 Amp Red 10 Amp Red 20 Amp Yellow Tire Pressure Monitor Snow Plow (Right) – If Equipped Instrument Panel Cluster Air Suspension Control Module – If
678 MAINTAINING YOUR VEHICLE Cavity F53 F54 F55 F56 F57 Cartridge Fuse Micro Fuse Description Cavity 20 Amp Yellow 20 Amp Yellow 20 Amp Yellow 15 Amp Blue Trailer Tow – Left Turn/Stop Lights Adjustable Pedals F58 20 Amp Yellow E38 Radio – If Equipped Additional Diesel Content – If Equipped Transmission F60 F61 F62 Cartridge Fuse Micro Fuse Description 20 Amp Yellow (Gas Engine) / 25 Amp Natural (Diesel Engine) 15 Amp Blue 20 Amp Yellow 10 Amp Red Engine Cooling Pump Underhood Lamp Power T
MAINTAINING YOUR VEHICLE 679 Cavity Micro Fuse Description Cavity F63 20 Amp Yellow F69 F64 25 Amp Natural 10 Amp Red 10 Amp Red IgnitionCoils (Gas), Urea Heater (Diesel) Fuel Injectors / Powertrain USB interface F65 F66 F67 Cartridge Fuse 10 Amp Red F70 F71 F72 Sunroof / Passenger Window Switches / Rain Sensor CD / DVD / Bluetooth Handsfree Module – If Equipped Cartridge Fuse Micro Fuse Description 15 Amp Blue 30 Amp Green 25 Amp Natural 10 Amp Red Mod SCR 12V – If Equipped Fuel Pump M
680 MAINTAINING YOUR VEHICLE Cavity F74 F75 F76 Cartridge Fuse Micro Fuse Description Cavity 20 Amp Yellow (Gas Engine) / 10 Amp Red (Diesel Engine) 10 Amp Red 10 Amp Red Brake Vacuum Pump Gas/Diesel – If Equipped Coolant Temperature Valve Actuator Antilock Brakes/ Electronic Stability Control Micro Fuse Description F77 10 Amp Red F78 10 Amp Red F79 15 Amp Blue 10 Amp Red Drivetrain Control Module/Front Axle Disconnect Module Engine Control Module / Electric Power Steering Clearance Light
MAINTAINING YOUR VEHICLE 681 Cavity Micro Fuse Description Cavity F82 10 Amp Red F88 F84 15 Amp Blue 10 Amp Red 10 Amp Red 10 Amp Red Steering Column Control Module/ Cruise Control Switch Bank/ Instrument Cluster Airbag Module F85 F86 F87 Cartridge Fuse F90/F91 F93 Airbag Module F94 Air Suspension-If Equipped / Trailer Tow / Steering Column Control Module F95 F96 Cartridge Fuse Micro Fuse Description 15 Amp Blue 20 Amp Yellow Instrument Panel Cluster Power Outlet (Rear seats) Customer
682 MAINTAINING YOUR VEHICLE Cavity Micro Fuse Description F97 25 Amp Natural F98 25 Amp Natural 10 Amp Red 15 Amp Blue Rear Heated Seats & Heated Steering Wheel – If Equipped Front Heated Seats – If Equipped Climate Control F99 F101 F104 Cartridge Fuse 20 Amp Yellow Electrochromatic Mirror / Smart High Beams – If Equipped Power Outlets (Instrument Panel/ Center Console) CAUTION! • When installing the power distribution center cover, it is important to ensure the cover is properly positioned a
MAINTAINING YOUR VEHICLE 683 VEHICLE STORAGE If you are storing your vehicle for more than 21 days, we recommend that you take the following steps to minimize the drain on your vehicle’s battery: • Disconnect the negative cable from battery. Interior Bulbs Bulb Number TS 212–9 Overhead Console Lamps Dome Lamp 7679 For lighted switches, see your authorized dealer for replacement instructions. • Any time you store your vehicle or keep it out of service (i.e.
684 MAINTAINING YOUR VEHICLE Bulb Number Projector Headlamp Low Beam Premium Bi Halogen Projector Headlamp High Beam Front Turn Signal Lamp (Premium Headlamp) Fog Lamp (Horizontal shape) Fog Lamp (Vertical shape) Center High Mounted Stop Lamp (CHMSL) Rear Cargo Lamp Cab Roof Marker Lamps 9005 LED (Serviced at Authorized Dealer) 9145 9006 921 921 194NA Base Rear Tail/Turn and Stop Lamp Premium Rear Tail/ Turn and Stop Lamp Premium Backup Lamp Rear Lamp Bar ID Marker Lamp Side Marker Lamps (Dual Rear Whee
MAINTAINING YOUR VEHICLE 685 BULB REPLACEMENT NOTE: Lens fogging can occur under certain atmospheric conditions. This will usually clear as atmospheric conditions change to allow the condensation to change back into a vapor. Turning the lamps on will usually accelerate the clearing process. 6. Remove the two headlamp assembly attachment screws. Base Quad / Premium Bi-Halogen: Low Beam Headlamp, High Beam Headlamp, Front Park And Turn – If Equipped 1. Open the hood. 2.
686 MAINTAINING YOUR VEHICLE 8. Reach through the access hole of the wheel house 10. Disconnect the wiring harness connectors from the splash shield and lift the slide lock upward far enough bulb socket. to disengage it from the lock post on the back of the 11. Replace bulb(s) as necessary. front lamp unit housing. CAUTION! • Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result.
MAINTAINING YOUR VEHICLE 687 Fog Lamps – If Equipped Rear Tail/Stop, Turn Signal And Backup Lamps 1. Reach under and behind the front bumper to access 1. Remove the two screws that pass through the bed the back of the front fog lamp housing. sheetmetal. 2. Disconnect the fog lamp wiring harness connector from the fog lamp bulb. 3. Rotate the bulb counterclockwise ¼ turn to unlock the bulb from the housing. 4. Pull the bulb straight out from the housing.
688 MAINTAINING YOUR VEHICLE 2. Pull the outboard side of the lamp rearward far 3. Disconnect the wiring harness connectors from the enough to unsnap the two receptacles on the outboard bulb socket. side of the lamp housing from the two plastic snap 4. Rotate the bulb socket counterclockwise 1/4 turn to post retainers in the outer box side panel. unlock it from the housing. 5. Pull the bulb straight out of the socket.
MAINTAINING YOUR VEHICLE 689 Center High-Mounted Stoplamp (CHMSL) With Cargo Lamp 2. Separate the connector holding the housing and wiring harness to the body. 1. Remove the two screws holding the housing/lens to the body as shown.
690 MAINTAINING YOUR VEHICLE 3. Turn the desired bulb socket ¼ turn and remove the socket and bulb from housing. 4. Pull the desired bulb straight from the socket. CAUTION! Do not contaminate the bulb glass by touching it with your fingers or by allowing it to contact other oily surfaces. Shortened bulb life will result. • Outside Bulbs: Cargo Lamps • Inside Bulb: Center High-Mounted Stop Lamp 5. Reverse the procedure for installation of bulbs and housing.
MAINTAINING YOUR VEHICLE 691 Cab Top Clearance Lamps – If Equipped 1. Remove the two screws from the top of the lamp. 2. Rotate the socket ¼ turn and pull it from the lamp assembly.
692 MAINTAINING YOUR VEHICLE 3. Pull the bulb straight from it’s socket and replace. 2. Rear Lamp Bar ID Marker (Dual Rear Wheels) — If Equipped 3. 1. Loosen the two screws and the housing to gain access 4. to the bulb sockets. Turn the socket ¼ turn counterclockwise to access the bulb. Pull the bulb straight out from the socket. Reverse the procedure for installation of the bulbs and housing.
MAINTAINING YOUR VEHICLE 693 Side Marker Lamps (Dual Rear Wheels) — If Equipped 1. Push rearward on the side marker lamp assembly. 2. Pull the entire assembly from the fender. 3. Turn the socket ¼ turn counterclockwise and remove from assembly to access the bulb. 4. Pull the bulb straight out from socket. 5. Reverse the procedure for installation of the bulbs and housing.
694 MAINTAINING YOUR VEHICLE FLUID CAPACITIES U.S. Fuel (Approximate) 1500 Regular Cab Shortbed/Crew Quad Cab Models 1500 Regular Cab Longbed/Crew Quad Cab Models (Optional) 2500/3500 Shortbed Models 2500/3500 Longbed Models Engine Oil With Filter 3.6L Engine (We recommend you use SAE 5W-20, API Certified) 4.7L Engine (We recommend you use SAE 5W-20, API Certified) 5.7L Engine (We recommend you use SAE 5W-20, API Certified) 5.7L Engine (We recommend you use SAE 5W-30, API Certified).
MAINTAINING YOUR VEHICLE 695 Cooling System 3.6L Engine (We recommend you use MOPAR® Antifreeze/ Coolant 10 Year/150,000 Mile Formula.) 4.7L Engine (We recommend you use MOPAR® Antifreeze/ Coolant 10 Year/150,000 Mile Formula.) 5.7L Engine – 1500 Models (We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula.) 5.7L Engine – 2500/3500 Models (We recommend you use MOPAR® Antifreeze/Coolant 10 Year/150,000 Mile Formula.) 5.
696 MAINTAINING YOUR VEHICLE FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil – 5.7L Engine For 2500/3500 trucks operating under a gross combined weight rating greater than 14,000 lbs/(6,350 kg.) Engine Oil Filter Spark Plugs – 3.6L Engine Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® Antifreeze/Coolant 10 Year/ 150,000 Mile Formula OAT (Organic Additive Technology).
MAINTAINING YOUR VEHICLE 697 Component Spark Plugs – 4.7L Engine Spark Plugs – 5.7L Engine Fuel Selection – 3.6L and 4.7L Engines Fuel Selection – 5.7L Engine Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® Spark Plugs. Upper Bank — (Gap 0.040 in [1 mm]) We recommend you use MOPAR® Spark Plugs. Lower Bank — (Gap 0.051 in [1.30 mm]) We recommend you use MOPAR® Spark Plugs (Gap 0.043 in [1.
698 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission — Eight-Speed Automatic Automatic Transmission — Six-Speed Automatic with Gasoline Engine (For Diesel Engine see Diesel Supplement) Transfer Case Front Axle – 1500 Four-Wheel Drive Models Rear Axle – 1500 Models Front and Rear Axle – 2500/3500 Models Fluid, Lubricant, or Genuine Part We recommend you use only MOPAR® ZF 8&9 Speed ATF™ Automatic Transmission Fluid or equivalent.
MAINTAINING YOUR VEHICLE 699 Component Brake Master Cylinder Power Steering Reservoir– 2500/3500 Models Fluid, Lubricant, or Genuine Part We recommend you use MOPAR® DOT 3. If DOT 3 brake fluid is not available, then DOT 4 is acceptable. We recommend you use MOPAR® Power Steering Fluid +4 or MOPAR® ATF+4® Automatic Transmission Fluid.
MAINTENANCE SCHEDULES CONTENTS 䡵 MAINTENANCE SCHEDULE . . . . . . . . . . . . .702 ▫ Maintenance Chart . . . . . . . . . . . . . . . . . . . .
702 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE Your vehicle is equipped with an automatic oil change indicator system. The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. Based on engine operation conditions, the oil change indicator message will illuminate. This means that service is required for your vehicle.
MAINTENANCE SCHEDULES 703 • Check the fluid levels of the coolant reservoir, brake master cylinder, power steering (2500/3500 Models Only) and automatic transmission (six-speed only) as needed • Check function of all interior and exterior lights Maintenance Chart Required Maintenance Refer to the Maintenance Schedules on the following pages for required maintenance. At Every Oil Change Interval As Indicated By Oil Change Indicator System: • Change oil and filter. • Rotate the tires.
Additional Inspections Inspect the CV joints. Inspect front suspension, tie rod ends, and replace if necessary. Inspect the front and rear axle surfaces. If gear oil leakage is suspected, check the fluid level. If using your vehicle for police, taxi, fleet, off-road or frequent trailer towing, change axle fluid. Inspect the brake linings, parking brake function. Inspect transfer case fluid.
Additional Maintenance Replace engine air filter. Replace spark plugs (3.6L engine).** Replace the top row (intake side) of spark plugs (4.7L Engine).** Replace the side row (exhaust side) of spark plugs (4.7L Engine).** Replace spark plugs (5.7L engine).
Replace the ignition cables (4.7L Engine). Flush and replace the engine coolant at 10 years or 150,000 miles (240,000 km) whichever comes first. Change automatic transmission fluid and filter(s), if using your vehicle for police, taxi, fleet, or frequent trailer towing. Change automatic transmission fluid and filter.
Inspect the transfer case fluid, change for any of the following: police, taxi, fleet, or frequent trailer towing. Change the transfer case fluid. Inspect and replace PCV valve if necessary.
708 MAINTENANCE SCHEDULES WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic. • Failure to properly inspect and maintain your vehicle could result in a component malfunction and effect vehicle handling and performance. This could cause an accident.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS 䡵 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE . . . . . . . . . . . . . . . . . . .711 ▫ Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) . . . . . . . . . . . . .713 ▫ Prepare For The Appointment . . . . . . . . . . . . .711 ▫ Service Contract . . . . . . . . . . . . . . . . . . . . . .713 ▫ Prepare A List . . . . . . . . . . . . . . . . . . . . . . . .711 䡵 WARRANTY INFORMATION . . . . . . . . . . . . .714 ▫ Be Reasonable With Requests .
710 IF YOU NEED CONSUMER ASSISTANCE 䡵 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES . . . . . . . . . . . . . . . . .717 ▫ Treadwear. . . . . . . . . . . . . . . . . . . . . . . . . . .717 ▫ Traction Grades . . . . . . . . . . . . . . . . . . . . . . .717 ▫ Temperature Grades. . . . . . . . . . . . . . . . . . . .
IF YOU NEED CONSUMER ASSISTANCE 711 SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment Be Reasonable With Requests If you list a number of items and you must have your vehicle by the end of the day, discuss the situation with the service advisor and list the items in order of priority. At many authorized dealer, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it is advisable to make these arrangements when you call for an appointment.
712 IF YOU NEED CONSUMER ASSISTANCE facilities, factory-trained technicians, special tools, and the latest information to ensure the vehicle is fixed correctly and in a timely manner. This is why you should always talk to an authorized dealer service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the authorized dealer. They want to know if you need assistance.
IF YOU NEED CONSUMER ASSISTANCE 713 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommunication Devices for the Deaf) equipment at its customer center. Any hearing or speech impaired customer, who has access to a TDD or a conventional teletypewriter (TTY) in the United States, can communicate with the manufacturer by dialing 1–800–380–CHRY. Warranty expires.
714 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment when you purchased the vehicle. An authorized dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with the ownership experience. You will be pleased with their sincere efforts to resolve any warranty issues or related concerns.
IF YOU NEED CONSUMER ASSISTANCE 715 If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA cannot become involved in individual problems between you, your authorized dealer, and the manufacturer. In Canada If you believe that your vehicle has a safety defect, you should contact the Customer Service Department immediately.
716 IF YOU NEED CONSUMER ASSISTANCE Service Manuals Owner’s Manuals These comprehensive Service Manuals provide the information that students and professional technicians need in diagnosing/troubleshooting, problem solving, maintaining, servicing, and repairing FCA US LLC vehicles. A complete working knowledge of the vehicle, system, and/or components is written in straightforward language with illustrations, diagrams, and charts.
IF YOU NEED CONSUMER ASSISTANCE 717 DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES significantly from the norm due to variations in driving habits, service practices, and differences in road characteristics and climate. The following tire grading categories were established by the National Highway Traffic Safety Administration.
718 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissipate heat, when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure.
INDEX 10
720 INDEX Adding Engine Coolant (Antifreeze) . . . . . . . . . . . .653 Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .531 Additives, Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . .526 Adjustable Pedals . . . . . . . . . . . . . . . . . . . . . . . . .177 Airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64, 74 Airbag Deployment . . . . . . . . . . . . . . . . . . . . . . . .79 Airbag Light . . . . . . . . . . . . . . . . . . . .
INDEX 721 Anti-Lock (ABS) . . . . . . . . . . . . . . . . . . . . .468, 470 Fluid Level Check . . . . . . . . . . . . . . . . . . .661, 662 Fluid Check . . . . . . . . . . . . . . . . . . . . . . . . . . .658 Fluid Type . . . . . . . . . . . . . . . . . . . . . . . . .661, 698 Master Cylinder . . . . . . . . . . . . . . . . . . . . . . . .658 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . .361, 372 Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .465 Special Additives . . .
722 INDEX Car Washes . . . . . . . . . . . . . . . . . . . . . . . . . . . . .665 Cellular Phone . . . . . . . . . . . . . . . . . . . . . . . . . . .313 Center High Mounted Stop Light . . . . . . . . . . . . . .689 Center Seat Storage Compartment . . . . . . . . . . . . .218 Certification Label. . . . . . . . . . . . . . . . . . . . . . . . .533 Chart, Tire Sizing . . . . . . . . . . . . . . . . . . . . . . . . .485 Check Engine Light (Malfunction Indicator Light) . . . . . . . . . . . . . . . . . . . . .
INDEX 723 Daytime Running Lights . . . . . . . . . . . . . . . . . . . .162 Dealer Service. . . . . . . . . . . . . . . . . . . . . . . . . . . .640 Defroster, Rear Window. . . . . . . . . . . . . . . . . . . . .224 Defroster, Windshield . . . . . . . . . . . . . . . . . . .120, 317 Delay (Intermittent) Wipers . . . . . . . . . . . . . . . . . .172 Differential, Limited-Slip . . . . . . . . . . . . . . . . . . . .436 Dipsticks Power Steering . . . . . . . . . . . . . . . . . . . . . . . . .
724 INDEX Tow Hooks . . . . . . . . . . . . . . . . . . . . . . . . . . . .621 Emission Control System Maintenance . . . . . . . . . .638 Engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .635, 636 Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . .644 Block Heater . . . . . . . . . . . . . . . . . . . . . . . . . .349 Break-In Recommendations . . . . . . . . . . . . . . . .117 Compartment . . . . . . . . . . . . . . . . . . . . . . . . . .634 Compartment Identification . . . .
INDEX 725 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . .531 Replacement Parts . . . . . . . . . . . . . . . . . . . . . . .530 Starting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .530 Flooded Engine Starting . . . . . . . . . . . . . . . . . . . .343 Fluid, Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . .698 Fluid Capacities . . . . . . . . . . . . . . . . . . . . . . . . . .694 Fluid Leaks . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
726 INDEX Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . .670 High Beam . . . . . . . . . . . . . . . . . . . . . . . . . . . .171 High Beam/Low Beam Select Switch . . . . . . . . .171 Passing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .170 Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .161 Head Restraints . . . . . . . . . . . . . . . . . . . . . . . . . .152 Heated Mirrors . . . . . . . . . . . . . . . . . . . . . . .135, 224 Heater. . . . . . . . . .
INDEX 727 Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12, 16 Ignition Key Removal . . . . . . . . . . . . . . . . . . . . . . .16 Illuminated Entry . . . . . . . . . . . . . . . . . . . . . . . . . .22 Immobilizer (Sentry Key) . . . . . . . . . . . . . . . . . . . .18 Infant Restraint . . . . . . . . . . . . . . . . . . . . . . . . . . .83 Inflation Pressure Tires . . . . . . . . . . . . . . . . . . . . .505 Inside Rearview Mirror . . . . . . . . . . . . . .
728 INDEX Airbag . . . . . . . . . . . . . . . . . . . . . .72, 81, 120, 259 Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .260 Anti-Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . .255 Anti-Lock Warning . . . . . . . . . . . . . . . . . . . . . .469 Automatic Headlights . . . . . . . . . . . . . . . . . . . .161 Brake Assist Warning . . . . . . . . . . . . . . . . . . . .480 Brake Warning . . . . . . . . . . . . . . . . . . . . . . . . .257 Bulb Replacement . . . . . . . .
INDEX 729 Turn Signal . . . . . . . . . . . . . . . . . .122, 170, 685, 687 Warning (Instrument Cluster Description) . . . . . .255 Limited-Slip Differential . . . . . . . . . . . . . . . . .436, 660 Loading Vehicle . . . . . . . . . . . . . . . . . . . . . . . . . .533 Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .490 Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 Automatic Door . . . . . . . . . . . . . . . . . . . . . . . . .36 Child Protection . . . .
730 INDEX New Vehicle Break-In Period . . . . . . . . . . . . . . . . .117 Onboard Diagnostic System . . . . . . . . . . . . . . . . . .637 Operating Precautions . . . . . . . . . . . . . . . . . . . . . .637 Occupant Restraints . . . . . . . . . . . . . . . . . . .47, 71, 79 Operator Manual (Owner’s Manual) . . . . . . . . . . . . .4 Occupant Restraints (Sedan) . . . . . . . . . . .67, 68, 71, 74 Outside Rearview Mirrors . . . . . . . . . . . . . . . . . . .132 Octane Rating, Gasoline (Fuel) . . . . . . .
INDEX 731 Pickup Box . . . . . . . . . . . . . . . . . . . . . . .228, 230, 247 Placard, Tire and Loading Information . . . . . . . . . .491 Power Distribution Center (Fuses) . . . . . . . . . . . . . . . .673 Door Locks . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 Mirrors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .134 Outlet (Auxiliary Electrical Outlet) . . . . . . . .207, 212 Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139 Sliding Rear Window . . . .
732 INDEX Remote Control Starting System . . . . . . . . . . . . . . . . . . . . . . . . .30 Remote Keyless Entry (RKE). . . . . . . . . . . . . . . .23, 24 Remote Sound System (Radio) Controls. . . . . . . . . .311 Remote Starting System. . . . . . . . . . . . . . . . . . . . . .30 Replacement Bulbs . . . . . . . . . . . . . . . . . . . . . . . .683 Replacement Keys . . . . . . . . . . . . . . . . . . . . . . . . .19 Replacement Parts. . . . . . . . . . . . . . . . . . . . . . . . .639 Replacement Tires .
INDEX 733 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .139 Rear Folding . . . . . . . . . . . . . . . . . . . . . . .149, 150 Reclining Rear . . . . . . . . . . . . . . . . . . . . . . . . .148 Security Alarm (Theft Alarm). . . . . . . . . . . . . . . . . .20 Selection of Coolant (Antifreeze). . . . . . . . . . . . . . .696 Sentry Key (Immobilizer) . . . . . . . . . . . . . . . . . . . .18 Sentry Key Programming . . . . . . . . . . . . . . . . . . . .20 Sentry Key Replacement . . . .
734 INDEX Engine Fails to Start . . . . . . . . . . . . . . . . . . . . .343 Remote . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30 Starting Procedures (Gas Engines) . . . . . . . . . . . . .340 Steering Power . . . . . . . . . . . . . . . . . . . . . . . . . . . .463, 464 Wheel, Heated . . . . . . . . . . . . . . . . . . . . . . . . .176 Wheel, Tilt . . . . . . . . . . . . . . . . . . . . . . . . . . . .175 Steering Wheel Audio Controls. . . . . . . . . . . . . . . .
INDEX 735 Pressure Warning Light . . . . . . . . . . . . . . . . . . .260 Quality Grading . . . . . . . . . . . . . . . . . . . . . . . .717 Radial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .498 Replacement . . . . . . . . . . . . . . . . . . . . . . . . . . .504 Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .508 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . .483, 495 Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .485 Snow Tires .
736 INDEX Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .698 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . .661 Shifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .350 Transmitter Battery Service (Remote Keyless Entry) . .29 Transmitter Programming (Remote Keyless Entry) . . .23 Transmitter, Remote Keyless Entry (RKE) . . . . . . . . .23 Tread Wear Indicators . . . . . . . . . . . . . . . . . . . . . .503 Turn Signals . . . . . . . . . . . . . . . . .
INDEX 737 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 Rear Sliding . . . . . . . . . . . . . . . . . . . . . . . . . . .225 Windshield Defroster. . . . . . . . . . . . . . . . . . . . . . .120 Windshield Washers. . . . . . . . . . . . . . . . .171, 172, 648 Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . .171, 648 Windshield Wiper Blades . . . . . . . . . . . . . . . . . . . .648 Windshield Wipers . . . . . . . . . . . . . . . . . . . . . . . .
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this vehicle’s electronic system to provide immunity to radio frequency signals. Mobile two-way radios and telephone equipment must be installed properly by trained personnel. The following must be observed during installation. The positive power connection should be made directly to the battery and fused as close to the battery as possible.
2013 RAM TRUCK 1500/2500/3500 FCA US LLC 13D241-126-AJ Tenth Edition Rev 1 Printed in U.S.A.
