User Manual
FCC Compliance Statement This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules.
About GPS The Global Positioning System (GPS) is a constellation of satellites that a GPS receiver uses to calculate geographical positions. To determine a position, data from at least three satellites is required. To determine elevation, the data from four or more satellites is required. Accuracy of the positioning varies from 10 feet to several hundred feet, depending on vehicle placement and the surrounding environment.
Table of Contents 1. Your Device ........................................................................................................................1 4. Destinations .....................................................................................................................30 What’s Included ............................................................................................................ 2 New Location ..............................................................................
1. Your Device Caution: Important Safety Information Navigation • Use this navigation device at your own risk. • Look at the display only when it is safe to do so. • • • • • Use this navigation device only when it is safe to do so. Traffic regulations always have priority over any instructions from the navigation system. Follow navigation system instructions only when local regulations and road traffic allow you do so.
1. Your Device TND 540: What’s Included •1 Rand McNally TND™ •3 Vehicle charger •2 •4 •5 Install the Mount Note: Follow all local regulations governing the placement of the mount. Suction cup mount with adjustable bracket 1. Select an area with a line of sight to the sky and GPS satellites. 2. Clean and dry the mounting area. Mini USB cable 3. Remove the suction cup protective film. Anti-glare screen protector 4. Adjust the angle of the mount using the thumbscrews. 5.
1.
1. Your Device TND 740: What’s Included Install the Mount •1 Rand McNally TND™ •3 Windshield mount with suction cup •2 •4 •5 •6 Note: Follow all local regulations governing the placement of the mount. Magnetic mount 1. Select an area with a line of sight to the sky and GPS satellites. 2. Clean and dry the mounting area. Vehicle charger 3. Remove the suction cup protective film. USB cable 4. Adjust the angle of the mount using the thumbscrews. Anti-glare screen protector 1 5.
1.
2. Settings Main Menu 1 2 3 4 11 10 9 8 7 6 1 Truck Tools Select to enter truck information, set warnings, and access other tools. 2 Go To Map Tap to view location on the map. 3 Guided Search Tap to select an address or point of interest (POI). 4 DriverConnect Tap to launch the DriverConnect app and log hours of service (HOS), Driver-Vehicle Inspection Reports (DVIRs), and other compliance fea tures.
2. Settings 1. Tap and to view the options. 2. Tap the option to be set. 3. Enter the new information. Page Truck Info Hazmat Type........................................................ 8 Weight (Empty) ................................................... 8 Weight (Loaded) ................................................ 8 Height .................................................................. 8 Width .................................................................. 8 Trailers ................
2. Settings Truck Info Options Truck Info Hazmat Type None Explosives Gases Flammable Liquids Flammable Solids Oxidizers Poison Radioactive Corrosives Other PIH Width Use the + and - buttons or enter a numeric value by tapping the calculator. Options Trailers Straight 48’ 53’ Double Triple Number of Axles Use the + and - buttons. Use the + and - buttons or enter a numeric Weight (Empty) value by tapping the calculator.
2. Settings Preferences and to view the options. • Tap • E nter the new information. • • ap the option to be set. T General Preferences Options My Custom POIs Manage Custom POIs Select a Category to Edit Hide All Icons on Map Go to Map Tap X to close and save changes.
2. Settings Preferences - continued Route Preferences General Preferences Options Toll Prompt/ Notification Enabled Disabled Clock Setting 12-Hour Clock 24-Hour Clock Contact & About Tap to show version information and copyrights. Route Preferences Set three distances at which you want to be warned about an upcoming turn. The first announcement will be the farthest from the turn and the third the closest.
2. Settings Preferences - continued Map Preferences Options .Map Style Light Dark High Contrast Map Auto Zoom Off On, Auto Scale On, Street Scale On, City Scale On, State Scale Set to auto scale to keep the current vehicle position and the next turn in the map view at all times. Set to street/city/state scale to specify the maximum scale of the zoom. Note: When in 3D Map mode with Auto Zoom on, the map will change to North Up at certain zoom levels.
2. Settings Preferences - continued Warning Preferences Warning/Alert Prompts Auto Dismiss Warnings Options None Audio & Visual Visual Audio Never After 2 Seconds After 10 Seconds After 30 Seconds Warning Preferences Options Warning Display Size Full Screen Small Bar Toll Booth Alert Set warning distance to toll booths by using the + and - buttons. Construction Area Set warning distance to construction areas by using the + and - buttons.
3. Maps Main Menu Basic Map View 1 1 Search For an Address Tap to type in any address or search by keyword. 2 2 Compass Direction Tap to change the map display. An icon displays the selected option: North up (N), heading up (arrow), or 3D. 3 4 5 6 3 ` 4 Route Distance Reflects the distance from your point of origin to your destination. 5 6 Expanded Map View 10 9 TND™ User Manual Map View Tab Tap to expand the map screen.
3. Maps Search For an Address 1. Tap the search bar at the top of the Navigation screen to type in any address or search by keyword. Or, tap any of the categories to search for specific types of destinations. 2. Once a destination is entered, tap Navigate and your route options will display. 3. Select either the fastest route or an alternate route. 4. Tap Start Navigation to begin the route.
3. Maps Helpful Tips on Entering Addresses Auto-Complete Feature Enter the first few characters in a name and a short list displays names that start with the typed characters. Continue entering characters until the searched-for name displays in the list. Tap the name to select it. Cities Cities with common names, such as “Athens”, may have multiple locations. The tablet will list all locations. If a name does not display, continue typing characters until the name you are looking for displays in the list.
3. Maps Points of Interest 1 3 2 You can also use the Map function to search for Points of Interest (POIs) along your route, or near your current location. POIs are organized by categories. 1 Tap a POI category in the Search bar. 2 Displays POIs nearby, or along your route. 3 Tap to view additional POI categories.. 4 Select a category, and locate a POI from the expanded list. Note: Turns red when speed limit warning exceeded. (See page 12 to set speed limit alert.) 4 5 Tap the POI.
3. Maps Route Map Window 1 3 2 5 7 15 14 13 11 10 1 ext Maneuver N Tap to repeat spoken next maneuver instructions. 2 oad Name R Name of street you will turn onto next. 3 8 12 ompass Direction C Tap to change the map display. An icon in the upper right corner displays the selected option: North up (N), heading up (arrow), or 3D (3). Also displays Wi-Fi status. Exits Quick View Slide out to show upcoming exit information.
3. Maps View Directions Detail View Route Display Options When first opened, the slide-out list displays in Detail View showing each maneuver. Use 1 2 and to view the instructions. To change the route display, choose Detail View, Highway View, Trip Summary (for multi-stop trips), or Map View (to view the route from start to finish). 1 Distance Displays the distance for each road segment. 2 Street/Road Name Displays the street name you will be on after performing the next maneuver.
3. Maps Directions Slide-Out List Highway View Route Display Options 1. When first opened, the slide-out list displays in Detail View showing each maneuver. 1 2. Use 2 3 istance D Displays the distance for each road segment. 5 6 treet/Road Name S Displays the street name you will be on after performing the next maneuver. Tap on any item in the list to view it on the map and to detour around it if necessary.
3. Maps View Directions Continued Trip Summary View (for multi-stop trips) Total (or Approximate) Distance and Time Displays the total distance and time for the entire multi-stop trip. 1 1 Leg Number of the leg (for multi-stop trips) and distance. 2 2 3 Map View (entire route) TND™ User Manual Destination Destination for that leg of the trip. 3 4 4 Remove Stop Tap to remove the stop from the trip.
3. Maps Exits Quick View Slide out to show Points of Interest and amenities at upcoming exits. The list displays the distance to the next exit, exit number, and a count of available amenities. 1. Tap an exit to bring up a list of POIs and amenities at that exit. 2. Tap All, Fuel, Food, or Hotel to display locations by category. 3. Tap any item in the list to route to that location.
3. Maps Route to Here, Set Origin, Add as Via You can drag the map with your finger to move it to another location. The crosshairs will display when you move the map. Place the crosshairs over the location you are looking for. When you find the location, press and hold the screen for a few seconds and choose Route to Here, Set Origin, or Add as Via. 1 3 5 2 4 7 1 Crosshairs Drag the crosshairs over the desired location. 2 Route to Here Tap Route to Here to navigate to the location.
3. Maps Add as Via (Multi-Stop Trips) To create a multi-stop trip, you must select and begin navigation to a location. Once the TND begins navigating, select another address (or POI), and select the Add as Via option. 1 2 1 Select Add as Via. 2 Select where to add the via point to the trip. You can add it to the begin ning of the trip, add it to the end of trip, or manually reorder multiple via points by selecting Reorder Trip.
3. Maps Alternate Routes / Avoid Tolls The TND Map will often select multiple routes to reach your destination. You can choose to navigate to any of the routes offered. The routes will display in different colors on the map. 1 1 Select Add as Via. 2 Select which route to use, and tap Start Navigation. If the selected route contains toll costs, a warning box displays.
3. Maps Junction View 1 2 3 5 4 hen on a route, Junction View displays when you have an upcoming W maneuver. Set distance in Preferences > Route. Once past the maneuver, Junction View closes and the previous window displays. 1 Signs to follow for the next maneuver. 2 Number and direction of lanes for the next maneuver. 3 Distance to the upcoming maneuver. Distance decreases as you approach the ramp. 4 Lane assist arrow. 5 Return to previous window. Turn View Displays for upcoming turns.
3. Maps 1 4 3 2 Location and Route Options 1 9 10 11 2 12 3 4 5 8 7 6 Nearest cross street Current road you’re on, current town you’re in Latitude and longitude at current location Return to previous window Detour Detour the entire route and add it to the avoid list. Around Part of the Route 1. O n the left side of the Window, tap the number of miles on the route to be avoided. 2. The route is recalculated. Around a Specific Roadway 1.
3. Maps Virtual Dashboard To show the Virtual Dashboard, tap the Current Speed. Tap here 6 5 1 3 8 9 7 2 4 12 TND™ User Manual 10 11 1 Current direction of travel. 2 Displays current times at the yard, current location and destination, as well as estimated time of arrival. 3 Sunrise and sunset times based on vehicle location (latitude/longitude) and day. 4 Current speed (above) and posted speed limit (below). Note: Turns red when speed limit warning exceeded.
3. Maps Manually Reset Trip Information 1. Tap on the tab you want to reset. 2. To set the odometer for the selected tab back to zero, tap Reset All. 3. Information is captured as you travel the route. Automatically Reset Trip Information To reset trip information after the vehicle has remained stationary after a specific number of hours: 1. T ap on the tab you want to reset. 2. Tap Auto Reset. 3. Tap 4. Tap to increase the number of hours. to decrease the number of hours. 5.
4. Destinations Destinations To access this window, tap Guided Search on the map. 1 2 3 4 1 Back Tap to return to the map. 2 ew Location N Tap to route to a new location by address, city center, intersection, or latitude/longitude. 3 History Tap to route to a recently entered location. 4 Address Book Tap to view a list of saved locations. 5 Multi-Stop Trips Tap to view a list of saved multi-stop trips or to create a new one.
4. Destinations Helpful Tips on Entering Addresses Auto-Complete Feature: Enter the first few characters in a name and a short list displays a couple of names that start with the typed characters. On the keyboard, the only keys available are for the next valid characters in a search name. Continue entering characters until the searched-for name displays in the list. Tap on the name to select it. Tap to view a longer list of names matching the typed characters. Cities: Add a space.
4. Destinations 4 1 2 5 TND™ User Manual 3 6 New Location 1 ddress A Tap to route to an address by entering the city, street, and number, or by entering the zip code and street. 2 City Center Tap to route to a city center. 3 Intersection Tap to route to two intersecting roads in a city. 4 Back Tap to return to the previous window. 5 Enter Lat/Long Tap to route to a location by latitude and longitude. 6 Go To Map Tap to return to the map.
4. Destinations Search for an Address 1. Tap Guided Search > New Location > Address. 2. Type the first few characters in the city name. As you type, a short list of matching city names displays. 3. Tap on a city to select it. • If the city is not displayed on the short name list, continue typing characters in the city name or tap List to display a long list of city names. Use the up and down arrows to view all cities/states. Tap on a city to select it.
4. Destinations Route to a City Center 1. Tap Guided Search > New Location > City Center. 2. T ype the first few characters in the city name. 3. T ap on the city/state name. The Confirmation Window displays. 4. Tap Begin New Route to navigate to the location. Route to an Intersection 5. Tap Guided Search > New Location > Intersection. 6. T ype the first few characters in the city name. 7. T ap on the city name. 8.
4. Destinations Route to a Latitude/Longitude 1. Tap Guided Search > New Location > Enter Lat/Long 2. Tap in the Latitude field. 3. Enter the latitude of the location and tap Enter. 4. Tap in the Longitude field. 5. Enter the longitude of the location and tap Enter. 6. Tap Go. The Confirmation Window displays. 7. Tap Begin New Route to navigate to the location. Note: There are two ways to enter latitude/longitude: by decimal degrees or by degrees, minutes, and seconds.
4. Destinations Address Book Add Locations to the Address Book from the Confirmation Window : 1. Tap Save to Address Book. 2. Tap Yes to accept the default name or tap No to display a keyboard. 3. T ype the name of the location and tap Enter to save the location in the Address Book. The Confirmation Window re-displays. Entries • Tap Guided Search > Address Book. Entries are alphabetically sorted by Name. • To sort by Distance or Date, tap Sort By.
4. Destinations Create a Group 1. 2. 3. 4. 5. 6. 7. Tap Guided Search > Address Book. T ap on the Groups tab. Tap New Group. Type the group name. To select a different color folder, tap Tap on a color, then tap Close. When finished, tap Enter. . Tap on the next to a group to delete the group. Addresses will still be saved in the Address Book. Note: You can also choose to display address book icons on the map. Add an Address to a Group 1. 2. 3. 4. 5. 6. Tap Guided Search > Address Book.
4. Destinations Create a Multi-Stop Trip 1. 2. 3. 4. ap Guided Search > Multi-Stop Trips. T Tap New Trip. ype the trip name. T o select a different color folder, tap T . 5. T ap on a color, then tap Close. 6. W hen finished, tap Enter. Note: A multi-stop trip can include up to 50 stops. Add a Stop Note: You can add locations in the order you want to route to them or reorder stops later From the Main Menu: 1. 2. 3. 4. ap Guided Search > Multi-Stop Trips. T Tap on the route.
4. Destinations Reorder Routes Optimize Automatically After all locations have been added to a multi-stop trip, you can run the optimizer wizard to organize your trip. 1. Tap Guided Search > Multi-Stop Trips. 2. Tap on the route you want to optimize. 3. Tap Reorder Trip. 4. Tap Automatic/Optimize. 5. Tap Select First Stop and select the first stop, or No Preference. 6. Tap Select Last Stop and select the last stop, or No Preference. 7.
4. Destinations Select and Run a Saved Route 1. Tap Guided Search > Multi-Stop Trips. 2. T ap on the route to select it. 3. T ap Start Trip. The Confirmation Window displays. 4. Tap Begin New Route to navigate to the location. 5. The TND™ calculates the route to your first stop. When you have reached the stop, a message displays. 6. Tap: • Next Stop - To calculate a route to the next stop in the route.
4. Destinations Avoid Options Avoid List From the map, set specific locations to avoid. Tap on the map and select Permanent Avoid. Choose Avoid Route, Avoid Road, or Avoid Area. Or, if the location is along an active route, choose Detour. Avoid Route Choose whether to avoid an upcoming distance on an active route, in the left column, or a specific road section, in the right column. Or, select Avoid Entire Route. The route is recalculated and the avoided sections are added to the Avoid List, under Routes.
4. Destinations 5 1 2 Points of Interest (POIs) 1 y Truck M Tap to search for a point of interest near the current vehicle location. 2 City Tap to search for a point of interest in a city. 3 y Route M Tap to search for a point of interest along the vehicle route. 4 estination D Tap to search for a point of interest near the route destination. 5 Back Tap to return to the previous window. 6 Custom POI Tap to select a custom POI location.
4. Destinations 8 1 4 TND™ User Manual 2 5 Points of Interest (POIs) 1 ravel Center T Tap to search for a travel center with truck amenities. (See page 28 to filter by amenities.) 2 Truck Services Tap to search for a truck services POI. (See page 28 to filter by amenities.) 3 Parking & Rest Areas Tap to search for truck parking or a rest stop. 4 Weigh Station/Border Crossings Tap to search for a truck weigh station and international border cross ings.
4. Destinations Other Categories 1. Tap Guided Search > Points of Interest. 2. Select a search type (My Truck/My Car, City, My Route, End of Day, or Destination). 3. Tap Other Categories. 4. Tap on a category. (For example, tap Hospital/Emergency.) 5. If necessary, tap on a subcategory type. (For example, tap Pharmacy.) 6. Tap on a location from the list or 7. Tap All. 8. Tap on the Spell button to display the keyboard. 9. Type the first characters in the POI name. 10.
4. Destinations Select and Filter Travel Center Amenities and Truck Services Truck-related Travel Center points of interest can include over 70 different types of amenities. To select only the travel centers with the amenities that you are interested in, filter your search results. 1. Tap Guided Search > Points of Interest. 2. Select a search type (My Truck/My Car, City, My Route, End of Day, or Destination). 3. Tap Travel Center or Truck Service. 4. Tap Select Services. 5.
4. Destinations Note: This feature requires a Wi-Fi connection. 1 2 3 Use Local Search to search the Internet for a restaurant, business, or any type of location by name, keyword, or category. Tap Guided Search > Local Search. Choose whether to search: 4 5 1 near your truck 2 in a specific city 3 near your destination Select a category, or tap Keywords to search using a specific name (e.g., “Subway”) or a keyword (“sandwich”).
4. Destinations Screens differ according to destination type: New Location 14 1 2 9 3 Confirmation Windows 1 2 3 4 6 5 8 7 5 Truck POI 14 1 6 2 9 4 3 7 4 6 8 5 11 9 10 Address Book 14 1 9 6 2 3 4 5 10 11 12 13 14 8 TND™ User Manual 8 12 13 estination Address D The selected location address. Begin New Route Tap to route to destination. Compare Routes Tap to choose between two routes Add as Via Add this location as an interim stop between the origin and destination.
4. Destinations Toll Costs From the destination confirmation screen, tap Begin New Route. If the calculated route includes tolls, a message appears. 1 2 3 1 Use Current Route Show estimated toll costs and continue along the calculated route. 2 Compare Routes Compare the calculated toll route to an alternate route without tolls. (See below.) 3 Don’t Prompt for Tolls Use the current route and disable this prompt for subsequent route calculations.
5. Tools & Features Wi-Fi For information on setting up a Wi-Fi hotspot through your cellular phone or laptop computer, please visit www.randmcnally.com/wifihelp for basic instructions, or contact your wireless carrier. Note: Wi-Fi connectivity requires a supporting feature and data plan from your wireless service provider. As the user, you are responsible for all data charges. Please contact your wireless service provider to make sure you do not exceed the limits of your data plan.
5. Tools & Features Weather Notes: • • 1 This feature requires a Wi-Fi connection. The refresh speed of the weather display is dependent on the connection speed. Weather information is updated every few minutes while Wi-Fi connection is active. Weather display depends on active weather patterns and map zoom level. • 3 2 To view current weather information and the three-day forecast for your location, tap the Live Data icon on the map screen and tap the Weather tab.
5. Tools & Features Fuel Prices Note: This feature requires a Wi-Fi connection. 1 2 TND™ User Manual 3 4 To show fuel prices, tap the Live Data icon on the map screen and tap the Fuel Prices tab. 5 1 Displays stations and prices, with distance as the crow flies. 2 Check to show the icons and prices on the map screen. 3 Sort by distance or price. 4 Apply filters for type of fuel and specific brand. 5 Check to show fuel prices along the route.
5. Tools & Features Traffic NOTE: This feature requires a Wi-Fi connection. To view current traffic information along your route and near your location: 1. Tap Live Data > Settings on the map screen. Tap the Traffic radio button to display the traffic overlay on the map. 2. Tap the Traffic tab. 3. T he Traffic tab displays traffic events along your route. Use the Flow and Incidents checkboxes to view or hide each type 4. of traffic events 5. Tap the X to return to the map. 6.
5.
5. Tools & Features Truck Tools Note: Some features are not available in Truck Mode. Tap Truck Tools on the Home screen to access the Truck Tools apps: Truck Info Enter truck information (weight, length, etc.). S tatus, Trails, Mileage, and Fuel View driving, on-duty, and maintenance timers; state logs; trails; and fuel purchase information. (See pages 44-47.) Motor Carrier’s Road Atlas Displays the Road Atlas app.
5. Tools & Features Status Note: Odometers count up and record the current mileage. Maintenance counters count down. When a maintenance timer counts down to 2,000 miles, a reminder displays each time the TND starts. 1. Tap Truck Tools. 2. Tap Status, Trails, Mileage, and Fuel. 3. Tap the Status tab. Tap a field to make adjustments to mileage. The mileage continue to count down from the changed value. 1. Tap -- to decrease the setting. 2. Tap + to increase the setting. 3.
5. Tools & Features Mileage 1. Tap Truck Tools. 2. Tap Status, Trails, Mileage, and Fuel. 3. Tap the Mileage tab to view list of logs for the current year, ordered by quarter. 4. To view quarterly mileage logs for previous years, tap Year. Tap on a quarter to view log entries. 5. Tap on a quarter to view details. Tap View by Date/View by State and Empty/Loaded for more information. To delete a log, tap on the Tap Yes to delete the log. next to the log entry to be deleted.
5. Tools & Features Trails Use Trails to record a “bread-crumb” path of GPS coordinates where your truck has traveled. 1. Tap Truck Tools. 2. Tap Status, Trails, Mileage, and Fuel. 3. Tap the Trails tab. 4. To record a trail, tap New Trail. 5. To end the trail, tap the pause icon on the map screen. 6. The trail is recorded in the Trails tab. 7. Tap on a trail to view details. 8. Tap Show on Map to display the trail on the map screen. 9. Tap Edit Name to change the name of the trail. 10.
5. Tools & Features Fuel Logs 1. Tap Truck Tools. 2. Tap Status, Trails, Mileage, and Fuel. 3. Tap the Fuel tab to view a list of fuel logs by quarter. 4. Tap +Fuel to record the date, location and cost of fuel purchase. 5. Tap on any field to edit. 6. Check Taxable to include the purchase in the fuel log. 7. Tap Save (Note: Fuel economy is calculated automatically.) 8. Once fuel purchases have been entered, tap on a quarter to view the details. 9. You can View by State or View by Month. 10.
5. Tools & Features Quick Planner Use this tool to quickly estimate the mileage and time between any two cities or towns. 1. Tap Truck Tools. 2. Tap Quick Planner. The revenue or cost per mile used in the last computation displays. 3. Tap From City 1 and select the city. 4. Tap To City 2 and select the city. 5. The distance displays. 6. Tap Cost per Mile and enter the per mile rate or tap Total and enter the total amount. 7. T ap the new dollar amount and tap Enter. 8.
5. Tools & Features Road Atlas Information To reference the Rand McNally Motor Carriers’ Road Atlas: 1. Tap Truck Tools. 2. Tap Motor Carrier’s Road Atlas. 3. Select the appropriate map from the drop-down on the right. 4. Select the legend on the left to view map information.
5. Tools & Features Calendar 1. Tap Truck Tools. 2. Tap Calendar. 3. Use the arrows to view other months and years. 4. Tap Today to return to the current date. Notes 1. Tap Truck Tools. 2. Tap Notes. 3. Tap New Note. 4. Tap a note in the list to view and edit. Unit Converter 5. T ap Truck Tools. 6. Tap Converter. 7. T ap on the first field and select the unit type. 8. T ap on the second field and enter the value to be converted. 9. Tap Enter. Calculator 1. Tap Truck Tools. 2.
6. DriverConnect DriverConnect The DriverConnect app provides a fully-compliant electronic logbook solution. DriverConnect lets you track and log Hours of Services,DriverVehicle Inspection Reports, Fuel purchases, and more. Reports can be generated for roadside inspections. The DriverConnect app connects to a Rand McNally Electronic Logging Device (ELD) over a Bluetooth connection.
7. Connect With Rand Tell Rand While you’re en route with your TND™, you can enter messages for Rand McNally regarding construction, truck restrictions, addresses, your device, and more. The next time you connect to the Rand McNally Dock, you can reopen, edit, and send the message. 1. Tap Truck Tools. 2. Tap Tell Rand. On the left side, tap Current Location. Enter Different Location or Find Location on Map.
6. Connect With Rand For more information TND™ User Manual • Rand McNally Website www.randmcnally.com/TND540 • Support www.randmcnally.com/support • GPS accessories store.randmcnally.com • Facebook www.facebook.
Trademarks Rand McNally, the Rand McNally logo, the globe logo, and IntelliRoute are registered trademarks and TND and Rand McNally Dock are trademarks of RM Acquisition LLC, d/b/a Rand McNally. The Trucker’s Friend and National Truck Stop Directory are registered trademarks of TR Information Publishers. TruckDown is a registered trademark of TruckDown Info International, Inc. Wi-Fi is a registered trademark of the Wi-Fi Alliance. InfoGation is a registered trademark of InfoGation Corporation.
