Spin Wheel™ Owner’s Manual www.ravesports.
Table of Contents Parts ................................................................................................................................... 2 Introduction ................................................................................................................... 3 Safety rules & information.......................................................................................... 4 Assembling your Spin Wheel .............................................................................
Introduction Thank you for purchasing a RAVE Sports® Spin Wheel™. This Owner’s Manual is presented to enhance your enjoyment of the sport and is intended to alert you to some of the potentially dangerous conditions that can arise in all water sports. It also contains important safety instructions and information about how to assemble, use and care for your product. Please take a few minutes to read this manual before assembling and using the product.
! WARNING UNSAFE USE OF THE SPIN WHEEL CAN RESULT IN PERSONAL INJURY OR DEATH. TO REDUCE THE RISK OF INJURY, READ AND FOLLOW ALL INSTRUCTIONS AND WARNINGS IN THIS MANUAL. DO NOT USE THIS PRODUCT UNLESS YOU UNDERSTAND AND ACCEPT THE RISK OF INJURY INVOLVED WITH THIS ACTIVITY. Safety Rules and Information • Read and understand all of the information contained in this owner’s manual before assembling and using your product.
• Never tow from a boat or other motorized vehicle, while people are on the product. • To avoid the possibility of a collision, make sure area around the Spin Wheel is clear of obstructions and other swimmers before each use. • Drowning Hazard: Never swim or play under the Spin Wheel. • Never use the product while tired or fatigued. Use extreme caution while swimming between the shore and the product. Do not attempt to swim this distance if you are tired or fatigued.
Assembling your Spin Wheel™ Track Inflation Roll out and unfold the Spin Wheel on flat ground. Make sure the area is free of rocks, sticks or other sharp objects that could puncture or damage the product. We highly recommend using the RAVE High Speed Inflator/Deflator. It will provide rapid inflation and deflation. (Item #01083, not included) To lock open valve, depress the stem and rotate ¼ OPEN turn clockwise. To close valve, depress the stem and rotate ¼ turn counter-clockwise.
DO NOT INFLATE SPIN WHEEL TRACK Beyond 8PSI to avoid damage. Use PSI gauge to ensure correct air pressure. To Deflate: Rapid deflation can be achieved using the “deflate” side of the motor housing. Attach the hose to the deflate side of the motor housing and lock the valve adaptor into the valve. Move to Water Due to its size, use 5 or more people to carry the product to the water CAUTION: To avoid risk of puncture or damage to the product, DO NOT DRAG the product. Always carry it to the water.
panels of the Bongo13 are aligned with the spokes on Spin Wheel. Step 2 Slide the straps that have the Velcro flaps in through the center opening of the Bongo13 jump surface loops. (As seen in Step 3) Step 3 NOTE: One person will need to be underneath the Bongo 13 for this step. Take the bottom strap and wrap it around the bottom of the tube and feed it through the stainless steel buckle. Pull down until it is tight. Tie a knot immediately adjacent to the buckle to prevent any possibility of slippage.
Remove all slack from anchor line and secure to swivel. Make sure the swivel is free to rotate. We recommend the (RAVE Anchor Connector Kit #01024). Folding Instructions Step 1 Remove Bongo 13 from Spin Wheel Track while in shallow water.
Step 2 Carry the Spin Wheel Track to land and deflate it. Be extremely careful not to drag the product. Step 3 Let the mat dry completely in the sun and then flip over and repeat for the other side. (Dry with a towel, if necessary, to ensure it is completely dry before folding). If there is algae build up, clean it off with a stiff bristle brush to clean it off. Step 4 Lay the Spin Wheel out and fold it according to the photos and diagrams provided here. Start by folding both sides to center.
Start at one end and begin to roll until it all contained in one bundle. Take a strap and cinch it tightly around the center to keep the bundle contained.
Cleaning and Storage • When the inflatable product is not being used, store it in a covered, shaded area. This will help protect it against ultraviolet (UV) rays and extend the life of the product. • Clean the inflatable completely with a mild soap and fresh water. NEVER USE PETROLEUM BASED PRODUCTS OR SOLVENTS FOR CLEANING. NEVER USE A POWER WASHER SINCE THE HIGH PRESSURE WATER JET WILL DAMAGE THE TUBE BEYOND REPAIR. • Product should be completely dry and remain dry while stored.
Repairs For large holes, tears or seam failures, contact RAVE Sports at 1-800-6590790. Additional repair patches can be found online at www.ravesports.com. For minor holes and tears: • Inflate the product and locate the leak by spraying the tube with mild soapy water. • Determine the hole size and cut a patch 1-2 inches wider than the diameter of the hole. Make sure all corners of the patch are rounded. • Deflate the product and clean the patch and area around the hole with rubbing alcohol.
This page is intentionally left blank 14
This page is intentionally left blank 15
www.ravesports.