Operation Manual
Pag.23
EN
8.2. Comfort clima
To enter in the USER MENU press two times key OK.
To enter in the menu “COMFORT CLIMA” press 6 times key 2 and con-
firm with OK. To modify the settings use keys 1 and 2 and by pressing OK
you confirm the data and go on to the following one.
By last confirmation with OK you save all settings and return automati-
cally to the screen with the icons.
To return to the main screen press at the same time keys 1 and 2.
EXAMPLE:
to activate it, press button P5 setting a value
other than OFF and the following strings will
appear on the display
The modulation phase is reached, as the
set room temperature has been reached. If
the temperature is maintained for about 4
minutes, the stove will shut down.
After the switching off phase, the display will
show ECO STOP. The stove will remain in
this state until the temperature drops to ap-
proximatly 18°C and only then will the igni-
tion phase be restarted.
The value set (in this case 2) has activated
the Comfort Clima function. FUNCTIONING:
The value sets the temperature the stove
goes back on again. Example
- room temperature set at 21°
- Comfort Clima value set at 2
with this setting, the stove will switch off when
21°C is reached and will be switched back
on when the room temperature is 18°C (21°C
– 2 – 0,5 = 18°C). The following strings will
appear in sequence on the display:
The functioning of the stove in COMFORT CLIMA mode can start up
the phase of ignition and switching off several times through the day:
this can compromise the duration of the resistance for the automatic
ignition of the stove.
8.3. Mode SILENCE (to activate see para. 7.2.8)
Mode SILENCE has been realized for reducing noise level of fan. It re-
duce the speed of the fan in all five working power.
Use is suggested especially during night time.
8.4. Mode SELF CONTROL SYSTEM (S.C.S. to activate see
para 7.2.9)
Mode SELF CONTROL SYSTEM (S.C.S) has been realized allowing the
stove to recognize faster an eventual problem just in case
you are out of home of far from the stove.
8.5. SERVICE HOURS
All our models need in addition to the regular cleaning (reference to the
paragraph dedicated to the maintenance of the stove in the user manual),
also a special cleaning which should be done by the installer (authorized
by the producer).
At the time of the installation it is possible to set a number of working hours
appropriate for the model following this procedure default settings>>extra
parameters>>TF53 service hours. At the end of these hours on the dis-
play will appear the message “SERVICE HOURS” followed by an acoustic
signal. When this message appears please contact the installer to do the
special cleaning of the stove.
If the cleaning is not done the message will appear by each ignition but
will not interrupt the functioning of the stove.
8.6. Automatic loading of the screw
To load automatically the screw (when the stove is new or the loading
scew is empty) please do following operations:
ENTER IN THE MENU
PRESS KEY OK TO
“STOVE STATUS”
ACTIVATE THE SCREW
Screw OFF Screw ON
1 2
To return to the main screen press at the same time keys 1 and 2.
Alternatively it is possible to exit by step from the menus by pressing each
time the key OK. Repeat the operation several times until you see the
pellet fall into the firepot.
It is possible to do this operation only if the
stove is in FINAL CLEANING phase or OFF.
8.7 Operating precautions
• In case of faulty operation turn the stove off pressing button no. 3.
• Do not manually load the fire pot with pellets.
• Any build up of unburned pellets inside the fire pot after repeatedly
trying to light the stove, must be removed before further attempts.
• Do not use any fuels other than wood pellets.
• Should the ignition system be faulty, do not attempt to light the stove
using flammable materials.
8.8. Remote control
IR receiver for remote control (12 volts batteries code LRV08 not included)
BASIC FUNCTIONS
• P1 - P2 Set temperature
allows to set the desired value for the
room temperature from “EST” to “MAN“
• P4 - P5 Set power
allows to set the working power between a
range of minimum 1 to maximum 5
• OK
by keeping pressed for 2 second longs it allows the manual
switch on and off of the stove
ADVANCED FUNCTIONS
• OK multifunction
if you press one time you can enter in the main
menu and the confi rmation of the setting. It is possible to exit step by
step from each menu by keeping pressed each time.
• P1 - P4
multifunction
to scroll the icons in the menu
• P2 - P5 multifunction to modify the setting in the men
8.9. Synthetic table of phases
PHASE DESCRIPTION
FINAL CLEANING The stove is switching off, the cooling phase is not yet completed
ON The ignition phase has started,the pellets are loaded into fi rebox
WAITING FOR FLAME The pellet is lighted by the hot air passing trought the ignition candle
FLAME PRESENT The fl ame is visibile in the fi re pot
WORKING The stove completed switch ON phase; you can change power
MODULATION WORKING The room temperature set has been reached
ECO STOP
Comfort Climate activated, temperature set has been reached; the
stove is off.
T ON
The room sensor is off or an external thermostat has been con-
nected
COOLING/WAITING FOR
START
The stove is cooling DOWN:when stove is cooled down can start
automatically.
COOLING/WAITING FOR
RESTART
The stove is in the cooling DOWN:when stove is cooled down can
restart automatically.
ON/WAITING FOR RESTART
The switch ON phase, when the stove is warm, started. The opera-
tion is same of phase ON
HOT SMOKE
The max temperature of smokes is reached: to reduce temperature,
feeding pellets and air draft reduce at POWER 01
OFF The stove is off
9. MAINTENANCE
Before carrying out any maintenance operation on the stove, please take
the following precautions:
•
Make sure that all the parts of the stove are cold
•
Make sure that the ashes are completely extinguished
•
Make sure that the general switch is in the zero position (off)
•
Make sure that the plug is disconnected from the socket, thus avoiding
accidental contacts
!!
PLEASE FOLLOW THE INSTRUCTIONS FOR CLEANING
SHOWN BELOW CAREFULLY! FAILURE TO OBSERVE THEM
MAY LEAD TO PROBLEMS IN THE FUNCTIONING OF THE
STOVE.
9.1. Cleaning the surfaces
To clean the surfaces on the painted metal parts, use a wet cloth in water
or at the most, water and soap.