Raymarine Limited 8-Pulse Width Radome Radars FCC ID: PJ5MTX2-8P & PJ5MTX4-8P Pathfinder Radar Scanners Owner's Handbook Note: The Owner's Handbook covers the new 8-Pulse Width Radome Scanner Units as well as the existing Open Array Scanner Units and is in final draft form. Raymarine Limited. Registered in England. Company No.
81154_6.
81154_6.
81154_6.book Page i Wednesday, October 10, 2001 10:48 AM Pathfinder Radar Scanners i Pathfinder Radar Scanners Owners Handbook December 2001 Intended Use The scanner units detailed in this handbook form part of navigational radar systems intended for light marine use. These radar systems are only an aid to navigation.
81154_6.book Page ii Wednesday, October 10, 2001 10:48 AM ii Pathfinder Radar Scanners Board Statement on Restrictions on Human Exposure to Static and Time Varying Electromagnetic Fields and Radiation, Doc NRPB, No. 5 (1993). 3. Navigation Aid. This radar unit is only an aid to navigation. Its accuracy can be affected by many factors, including equipment failure or defects, environmental conditions, and improper handling or use.
81154_6.book Page iii Wednesday, October 10, 2001 10:48 AM Pathfinder Radar Scanners iii Preface This handbook describes the following Raymarine Pathfinder radar scanners: 2D 4D 5S 7S 9S 11S 18" 24" 48" 72" 48" 72" 2 kW Radome Scanner 4 kW Radome Scanner 4 kW Open Array Scanner 4 kW Open Array Scanner 10 kW Open Array Scanner 10 kW Open Array Scanner These scanner units may be connected to any HSB/hsb2 display unit.
81154_6.book Page iv Wednesday, October 10, 2001 10:48 AM iv Pathfinder Radar Scanners Note: If a scanner unit is not connected the version number is only displayed for 10 seconds. Where, necessary Software Upgrade Kits are available from your dealer, distributor or from Raymarine. We recommend that where a repeater display is fitted, both the repeater and the master display are upgraded.
1154_6.book Page v Wednesday, October 10, 2001 10:48 AM v Certificate No. RT009 We Raymarine Limited Anchorage Park Portsmouth Hampshire England P03 5TD declare, under our sole responsibility, that the products identified in this declaration, and to which this declaration relates, are in conformity with the essential requirements of European Parliament and Council Directive: 1999/5/EC on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity.
81154_6.book Page vi Wednesday, October 10, 2001 10:48 AM vi Pathfinder Radar Scanners Certificate No. RT009 Declaration of Conformity – Schedule of Ancillary Equipment and Radar Systems The following Raymarine Display Units are combined with the Raymarine or Raytheon 2D – 2kW, 18" Radome Scanner Unit (transceiver) listed on Sheet 1 to form the operational radar systems given below.
81154_6.book Page vii Wednesday, October 10, 2001 10:48 AM vii Certificate No. RT010 We Raymarine Limited Anchorage Park Portsmouth Hampshire England P03 5TD declare, under our sole responsibility, that the products identified in this declaration, and to which this declaration relates, are in conformity with the essential requirements of European Parliament and Council Directive: 1999/5/EC on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity.
81154_6.book Page viii Wednesday, October 10, 2001 10:48 AM viii Pathfinder Radar Scanners Certificate No. RT010 Declaration of Conformity – Schedule of Ancillary Equipment and Radar Systems The following Raymarine Display Units are combined with the Raymarine or Raytheon 4D – 4kW, 24" Radome Scanner Unit (transceiver) listed on Sheet 1 to form the operational radar systems given below.
81154_6.book Page ix Wednesday, October 10, 2001 10:48 AM ix Certificate No. RT011 We Raymarine Limited Anchorage Park Portsmouth Hampshire England P03 5TD declare, under our sole responsibility, that the products identified in this declaration, and to which this declaration relates, are in conformity with the essential requirements of European Parliament and Council Directive: 1999/5/EC on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity.
81154_6.book Page x Wednesday, October 10, 2001 10:48 AM x Pathfinder Radar Scanners RT011 Declaration of Conformity – Schedule of Ancillary Equipment and Radar Systems The following Raymarine Display Units are combined with the Raymarine or Raytheon 4kW, Open Array Scanner Unit (transceiver) listed on Sheet 1 to form the operational radar systems given below.
81154_6.book Page xi Wednesday, October 10, 2001 10:48 AM xi Certificate No. RT012 We Raymarine Limited Anchorage Park Portsmouth Hampshire England P03 5TD declare, under our sole responsibility, that the products identified in this declaration, and to which this declaration relates, are in conformity with the essential requirements of European Parliament and Council Directive: 1999/5/EC on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity.
81154_6.book Page xii Wednesday, October 10, 2001 10:48 AM xii Pathfinder Radar Scanners RT012 Declaration of Conformity – Schedule of Ancillary Equipment and Radar Systems The following Raymarine Display Units are combined with the Raymarine or Raytheon 10kW, Open Array Scanner Unit (transceiver) listed on Sheet 1 to form the operational radar systems given below.
81154_6.book Page xiii Wednesday, October 10, 2001 10:48 AM xiii Contents Chapter 1: Overview ...............................................................................1 1.1 Introduction ....................................................................... 1 EMC installation guidelines ............................................. 2 1.2 Unpacking and inspecting the components ...................... 4 1.3 Selecting the scanner unit site ........................................... 5 1.4 Cable runs .
81154_6.
81154_6.book Page 1 Wednesday, October 10, 2001 10:48 AM Chapter 1: Overview 1 Chapter 1: Overview 1.1 Introduction This handbook provides instructions to assist you in the installation and set up of the following radar scanners: 2D 4D 5S 7S 9S 11S 18" 2 kW Radome Scanner 24" 4 kW Radome Scanner 48" 4 kW Open Array Scanner 72" 4 kW Open Array Scanner 48" 10 kW Open Array Scanner 72" 10 kW Open Array Scanner These scanner units may be connected to any HSB/hsb2 display unit.
81154_6.book Page 2 Wednesday, October 10, 2001 10:48 AM 2 Pathfinder Radar Scanners CAUTION: Do not use an open array scanner with an SL70 or SL70 PLUS 7" LCD display unit. Failure to observe this may result in permanent damage to these display units. The 10 kW open array scanner requires 24 V or higher; it will not operate on 12 V systems. This handbook is divided into three chapters as follows: Chapter One provides an overview of the scanner installation.
81154_6.book Page 3 Wednesday, October 10, 2001 10:48 AM Chapter 1: Overview • • • 3 In the case of SSB radios, the distance should be increased to 2 m (7 ft). • More than 2 m (7 ft) from the path of a radar beam. A radar beam can normally be assumed to spread 20 degrees above and below the radiating element. The equipment is supplied from a separate battery from that used for engine start.
81154_6.book Page 4 Wednesday, October 10, 2001 10:48 AM 4 Pathfinder Radar Scanners 1.2 Unpacking and inspecting the components Unpack your system carefully, to prevent damage to the equipment. It is good practice to save the carton and packing for future use, in case you need to return the unit for service. Check that you have all the correct system components. These depend on your system package, as detailed in the following tables. Table 1-1: Radome scanners Item Part No.
81154_6.book Page 5 Wednesday, October 10, 2001 10:48 AM Chapter 1: Overview 5 1.3 Selecting the scanner unit site This section provides information that affects the possible locations of the scanner, and its position relative to the display unit and to the power supply. The dimensions of the each scanner unit are shown in the following diagrams.
81154_6.book Page 6 Wednesday, October 10, 2001 10:48 AM Pathfinder Radar Scanners 227 mm (8.9 in) 6 Rear 302.5 mm (11.9 in) 151.25 mm (5.95 in) 116.5 mm (4.6 in) Rear 233 mm (9.2 in) 468 mm (18.4 in) dia. Weight: 6.5 kg (14.3 lbs) Compass safe distance: 1 m (33 in) 18" Radome Scanner D3224_4 227 mm (8.9 in) 141.5 mm (5.6 in) Rear 402 mm (15.8 in) 185.15 mm (7.3 in) 116.5 mm (4.6 in) Rear 233 mm (9.2 in) 599 mm (23.6 in) dia. Weight: 7.5 kg (16.
81154_6.book Page 7 Wednesday, October 10, 2001 10:48 AM Chapter 1: Overview 7 Open Array Scanners 48"- 1306 mm (51.4 in), 72"- 1928 mm (75.9 in) Centre of rotation 406 mm (16 in) Centre of rotation 100 mm (4 in) 427 mm (16.8 in) Weight Pedestal: 24 kg (53.0 lb) 48" Open Array: 6 kg (13.2 lb) 72" Open Array: 9.4 kg (20.7 lb) Compass Safe Distance: 1 m (33 in) Minimum clearance height 510 mm (20.1 in) 150 mm (6 in) 70 mm (2.75 in) 140 mm (5.5 in) 296 mm (11.65 in) Minimum clearance 630 mm (24.
81154_6.book Page 8 Wednesday, October 10, 2001 10:48 AM 8 Pathfinder Radar Scanners • • • • • • Access: The scanner unit site should be easily accessible to allow maintenance to be carried out safely. Magnetic compass: Mount the scanner unit at least 1 m away from a magnetic compass. Cable run: The maximum length of cable between the display unit and the scanner unit should not normally exceed 20 m (60 ft) for radome scanners, or 15 m (45 ft) for open array scanners.
81154_6.book Page 9 Wednesday, October 10, 2001 10:48 AM Chapter 1: Overview 9 For open array scanners you should also consider the following points: • • • Mounting Platform: The platform must be mechanically secure and capable of supporting the mass and inertia of the open array scanner. The complete unit weighs: 48" scanner - 30 kg (66.2 lb); 72" scanner - 33.4 kg (73.7 lb). The site must be clear of ropes and moving rigging.
81154_6.book Page 10 Wednesday, October 10, 2001 10:48 AM 10 Pathfinder Radar Scanners Setting the radiation plane The scanner unit should be mounted so that the array rotates parallel to the waterline. The radar beam is approximately 25° wide in the vertical direction, providing good target detection during the vessel’s pitching and rolling. 12.5˚ 12.
81154_6.book Page 11 Wednesday, October 10, 2001 10:48 AM Chapter 1: Overview 11 1.4 Cable runs You need to consider the following before installing the system cables: • • • • • You need to fit the inter-unit cable and the power cable. All cables should be adequately clamped and protected from physical damage and exposure to heat - avoid running cables through bilges or doorways, or close to moving or hot objects. Acute bends must be avoided.
81154_6.book Page 12 Wednesday, October 10, 2001 10:48 AM 12 Pathfinder Radar Scanners If you are mounting the scanner on the mast of a sailboat, and will need to unstep the mast, you should install a suitable junction box inside the boat. On a radome scanner, the junction box should provide an 11- or 13way terminal strip, depending on the number of power cores in your cable, with a 10 A rating.
81154_6.book Page 13 Wednesday, October 10, 2001 10:48 AM Chapter 1: Overview 13 Radome scanner cables Inter-unit cable The length of the supplied cable should be sufficient to complete the cable run required on most small vessels. For longer runs, additional or replacement cables are available, which have 4 power cores to minimize voltage drops over the longer cable run: these optional cables include 5 m and 10 m extension cables, and a 25 m replacement cable.
81154_6.book Page 14 Wednesday, October 10, 2001 10:48 AM 14 Pathfinder Radar Scanners Power cable The radome radar systems are intended for use on ships’ DC power systems operating in the 10.7 to 32 V DC range (that is, 12 V and 24 V systems, not 32 V systems). A 1.5 m (5 ft) power cable is supplied (with the display unit) for connecting the ship’s DC power to the radar scanner via the display unit. Refer to the HSB/hsb2 Series Display Owner’s Handbook for details on connecting this cable.
81154_6.book Page 15 Wednesday, October 10, 2001 10:48 AM Chapter 1: Overview 15 Table 1-5: Max. Extension Power Cable Lengths (m), 12 V Systems 18" Radome Scanner Inter-Unit Cable(s) Power Cable Core (each core) mm2: 1.5 AWG: 16 2.0 15 2.5 14 4.0 11 6.0 10 10.0 7 10 m Light 5.0 7.0 9.0 14.0 20.0 35.0 10 m Light + 5 m ext 1.0 2.0 3.0 4.5 7.0 12.0 10 m Light + 10 m ext Do NOT extend the power cable 15 m Light 1.0 2.0 3.0 4.5 7.0 12.0 15 m Heavy 7.0 10.0 13.0 20.0 30.
81154_6.book Page 16 Wednesday, October 10, 2001 10:48 AM 16 Pathfinder Radar Scanners Open array scanner cables Inter-unit cable Heavy duty cables are available in 15 m and 25 m lengths which should be sufficient to complete the cable run required on most small vessels. For longer runs, 5 m and 10 m extension cables are available, both have 4 power cores to minimize voltage drops over the cable run and incorporate in-line moulded plugs.
81154_6.book Page 17 Wednesday, October 10, 2001 10:48 AM Chapter 1: Overview 17 24 V and 32 V Systems - 10kW scanners 10 kW open array scanners can use any combination of inter-unit cable up to a maximum length of 35 m. However, these systems use considerable power and installations should be planned to minimize all cable lengths. Refer to the tables on page 1-19, Max. Extension Power Cable Lengths (m) - 10 kW Scanner.
81154_6.book Page 18 Wednesday, October 10, 2001 10:48 AM 18 Pathfinder Radar Scanners maximum power cable extensions are given in the table below. These figures relate to the total cable extension, from the end of the supplied 1.5 m power cable to the system battery terminals. Do not exceed these lengths as unreliable operation may result. Table 1-8: Max. Extension Power Cable Lengths (m), 12 V Systems 4 kW scanners Power Cable Core Size (each core) mm2: 4.0 AWG: 11 4 kW Scanners <3.0 6.0 10 8.
81154_6.book Page 19 Wednesday, October 10, 2001 10:48 AM Chapter 1: Overview 19 Table 1-9: Max. Extension Power Cable Lengths (m), 24/32 V Systems 4 kW Scanners Power Cable Core Size (each core) mm2: 2.0 AWG: 14 4 kW Scanners 8.0 4.0 11 6.0 10 8.0 8 10.0 7 16.0 24 32 35 Table 1-10:Max. Extension Power Cable Lengths (m), 24 V Systems 10 kW Scanners Inter-Unit Cable(s) Power Cable Core (each core) mm2: 1.5 AWG: 16 2.0 15 2.5 14 4.0 11 5 m Heavy 12.0 16.0 20.0 32.0 10 m Heavy 10.
81154_6.
81154_6.book Page 21 Wednesday, October 10, 2001 10:48 AM Chapter 2: Installing the Scanner 21 Chapter 2: Installing the Scanner 2.1 Radome scanner Securing the radome scanner to the mounting surface CAUTION: The drain tube must always be used, but may be shortened if necessary 1. Using the paper template supplied with the scanner mounting kit, mark the flat mounting surface with the mounting holes and drain tube hole, and drill the holes as indicated on the template.
81154_6.book Page 22 Wednesday, October 10, 2001 10:48 AM 22 Pathfinder Radar Scanners Scanner base Bitumen washer Mounting bracket or mounting surface Greased mounting bolt D3995-3 You may need to use longer M8 mounting bolts to secure the scanner if you have used shims to lower the radar beam. Connecting the radome scanner inter-unit cable CAUTION: Before wiring the scanner unit, make sure that the inter-unit cable is not connected and power is not applied to the display unit.
81154_6.book Page 23 Wednesday, October 10, 2001 10:48 AM Chapter 2: Installing the Scanner 23 Inner cover D4006-2 4. Remove the drain tube from inside the base of the scanner, and insert it into the drain hole as shown in the following diagram. Pull the tube gently from outside the scanner so that it clips into place.
81154_6.book Page 24 Wednesday, October 10, 2001 10:48 AM 24 Pathfinder Radar Scanners 5. Referring to the following illustration, remove the securing nut (1) from the watertight gland and grommet (2), where the interunit cable (3) will enter the base. White wire 8 10 7 4 5 6 11 9 2 1 3 D3230-4 1 Securing nut 2 Gland 3 Inter-unit cable 4 Eight-way plug 5 Eight-way socket 6 Power cores (2 or 4) 7 Terminal clamp 8 Screwdriver 9 Cable clamp 10 Cable clamp screws 11 Ferrite clamp 6.
81154_6.book Page 25 Wednesday, October 10, 2001 10:48 AM Chapter 2: Installing the Scanner 25 CAUTION: If any wires are damaged when the clamp is fitted, the scanner unit will not function correctly. • • The ferrite clamp is supplied open. If the clamp has been closed, insert a small, flat-blade screwdriver into the slots at the end of the clamp opposite the hinge and twist gently.
81154_6.book Page 26 Wednesday, October 10, 2001 10:48 AM 26 Pathfinder Radar Scanners ing on the thickness of the cable: use the position that matches the profile of the cable. CAUTION: It is essential that the drain tube is fitted and that the nut on the watertight gland is adequately tightened. If this is not done, water could become trapped in the scanner and cause irreparable damage. 13. Tighten the securing nut (1) again to ensure a waterproof seal. 14.
81154_6.book Page 27 Wednesday, October 10, 2001 10:48 AM Chapter 2: Installing the Scanner 27 2.2 Open array scanner Installation of the open array scanner should only be undertaken by a competent installer. If you have any difficulty with the installation, please contact your local Raymarine dealer or distributor. The open array scanner is supplied in two sections; the pedestal unit and the antenna. The pedestal unit is secured from below the mounting platform.
81154_6.book Page 28 Wednesday, October 10, 2001 10:48 AM 28 Pathfinder Radar Scanners Securing the pedestal to the mounting platform 1. Using the paper template supplied with the scanner mounting kit, mark the flat mounting surface with the holes and drill as indicated on the template. Refer to Section 1.2 when selecting the scanner unit site. 2. Stick the four self-adhesive bitumen washers over the mounting holes. 3.
81154_6.book Page 29 Wednesday, October 10, 2001 10:48 AM Chapter 2: Installing the Scanner 29 Pedestal Lifting eye IMPORTANT Bitumen washer, MUST be sticky side down on mounting platform Mounting platform 32 mm max.
81154_6.book Page 30 Wednesday, October 10, 2001 10:48 AM 30 Pathfinder Radar Scanners . Heatshrink 5mm (0.2in) 5mm (0.2in) 20mm (0.8in) 20mm (0.8in) 40mm (1.6in) D4575-2 4. Slide the cable through the gland nut, washer and grommet, then into the base. Clamp into position, ensuring the section of main cable covered in yellow heat shrink is clamped. 5. The cable is supplied prepared and ready to fit to the signal and power connectors.
81154_6.book Page 31 Wednesday, October 10, 2001 10:48 AM Chapter 2: Installing the Scanner 31 1. Preparation of Wires 500mm ± 10mm 5-6mm strip length Black power wires Red power wires Data wires (6 off) See Note A Coaxial signal 25mm See Note B Coaxial screen 10mm 500mm ± 10 mm 2. Heat Shrinking of Wires 5-6mm strip length 35mm 5mm maximum 25mm See Note D See Note C 3. Heat Shrinking of Cable/Wires 40mm 20mm Notes A. Aluminium screen/polyester tape screen to remain. B.
81154_6.book Page 32 Wednesday, October 10, 2001 10:48 AM 32 Pathfinder Radar Scanners Re-connect to the plug. When correctly fitted the white wire (coaxial) will be at the outer edge of the unit. 6. Connect the red and black power cores. Connect the red cable leads to the terminal sockets marked “+”, and the black cable leads to the terminal socket marked “-”, with one lead in each socket. The terminal clamps are operated using a screwdriver as shown in the inset diagram.
81154_6.book Page 33 Wednesday, October 10, 2001 10:48 AM Chapter 2: Installing the Scanner 33 the mounting bracket) as you lower the rear of the lid. Tighten the four self-retaining bolts. CAUTION: Do not grease the gasket in the pedestal lid. Fitting the open array to the pedestal CAUTION: The pedestal unit has a cap fitted over the open array mounting shaft to protect the protuding co-axial pin. This cap must be left in place until the open array is fitted to the pedestal. 1.
81154_6.
81154_6.book Page 35 Wednesday, October 10, 2001 10:48 AM Chapter 2: Installing the Scanner 35 2.3 System connections DC power connection Power is supplied to the scanner via the display unit; the power cable is supplied with the display unit, refer to your display unit Owner’s Handbook for details on connecting power. However, you should be aware of the following. The DC system should be either: • • Negative grounded, with the negative battery terminal connected to the ship’s ground.
81154_6.book Page 36 Wednesday, October 10, 2001 10:48 AM 36 Pathfinder Radar Scanners CAUTION: If you do not have a thermal circuit breaker or fuse in your power circuit, e.g. fitted to the DC distribution panel, you MUST fit an in-line breaker or fuse to the positive (red) lead of the power cable. Table 2-1: Isolator Switch/Thermal Breaker/Fuse Values Vessels Supply 12 V* 24/32 V** Device Open Array Systems 4 kW 10 kW Radome Systems Isolator Switch min.
81154_6.book Page 37 Wednesday, October 10, 2001 10:48 AM Chapter 2: Installing the Scanner 37 Front view of Display Cable Connector 8 7 1 2 5 3 4 8 6 7 11 9 13 10 12 Display 1 Video RTN 2 *Battery --ve 3 Battery --ve Data I/O + Tx Trigger -- 6 5 4 3 2 1 Not fitted on Open Array Scanners (refer to Section 2.
81154_6.book Page 38 Wednesday, October 10, 2001 10:48 AM 38 Pathfinder Radar Scanners Display unit connection CAUTION: Do not use an open array scanner with an SL70 or SL70 PLUS 7" LCD display unit. Failure to observe this may result in permanent damage to the display unit. 10 kW open array scanners cannot be directly connected to 12 V systems.
81154_6.book Page 39 Wednesday, October 10, 2001 10:48 AM Chapter 3: Post Installation Checks and Maintenance 39 Chapter 3: Post Installation Checks and Maintenance Once you have installed your radar scanner and display unit, and made all the connections, you need to check your installation. You can then set up the radar system, align the scanner and check the display timing.
81154_6.book Page 40 Wednesday, October 10, 2001 10:48 AM 40 Pathfinder Radar Scanners which the unit should enter Standby mode. If necessary, adjust the lighting and contrast. If required, change the default language settings. Checking transmission WARNING: The radar scanner transmits electromagnetic energy. Ensure that the scanner has been installed according to the recommendations given in Chapter 1, and that all personnel are clear of the scanner, before switching to transmit mode.
81154_6.book Page 41 Wednesday, October 10, 2001 10:48 AM Chapter 3: Post Installation Checks and Maintenance 41 3.2 Maintenance Warnings The display unit and scanner unit contain high voltage. Adjustments require specialized service procedures and tools only available to qualified service technicians - there are no user serviceable parts or adjustments and the operator should not attempt to service the equipment.
81154_6.book Page 42 Wednesday, October 10, 2001 10:48 AM 42 Pathfinder Radar Scanners • • enable you to ensure minimum interaction between different items of equipment, i.e. ensure optimum Electromagnetic Compatibility (EMC). Always report any EMC-related problem to your nearest Raymarine dealer. We use such information to improve our quality standards. In some installations, it may not be possible to prevent the equipment from being affected by external influences.
81154_6.book Page 43 Wednesday, October 10, 2001 10:48 AM Chapter 3: Post Installation Checks and Maintenance 43 How to Contact Raymarine (US) For Marine Product and Services Information Visit the Raymarine World Wide Web site for the latest information on the newest Raymarine electronic equipment and systems at: www.raymarine.com For Accessories and Parts Many Raymarine accessory items and parts can be obtained directly from your authorized Raymarine dealer.
81154_6.book Page 44 Wednesday, October 10, 2001 10:48 AM 44 Pathfinder Radar Scanners For Product Repair and Service In the unlikely event your Raymarine unit should develop a problem, please contact your authorized Raymarine dealer for assistance. The dealer is best equipped to handle your service requirements and can offer time saving help in getting the equipment back into normal operation.
81154_6.book Page 45 Wednesday, October 10, 2001 10:48 AM Chapter 3: Post Installation Checks and Maintenance 45 Technical Support The Technical Services Department handles enquiries concerning installation, operation, fault diagnosis and repair. For technical help desk contact: Tel: Fax: +44 (0) 23 9271 4713 +44 (0) 23 9266 1228 Our technical support staff may also be reached via e-mail at: techsupport@Raymarine.com.
81154_6.
154_6A1.fm Page 47 Wednesday, October 10, 2001 10:58 AM Appendix A: Specification 47 Appendix A:Specification 2D 18" Radome Scanner Unit General Approvals CE - conforms to FCC - conforms to 1999/5/EC, EN60945 Part 80 (47CFR) and Part 2 (47CFR) Dimensions Φ468 x 227 mm (18.4 x 8.9 in) Weight 6.5 kg (14.3 lbs) Input Voltage 8.
81154_6.book Page 48 Wednesday, October 10, 2001 10:48 AM 48 Pathfinder Radar Scanners Antenna Antenna Type Patch array Beam Width (nominal) 5.
154_6A1.fm Page 49 Wednesday, October 10, 2001 10:56 AM Appendix A: Specification 49 4D 24" Radome Scanner Unit General Approvals CE - conforms to FCC - conforms to 1995/5/EC, EN60945 Part 80 (47CFR) and Part 2 (47CFR) Dimensions Φ599 x 227 mm (23.6 x 8.9 in) Weight 7.5 kg (16.5 lbs) Input Voltage 8.
81154_6.book Page 50 Wednesday, October 10, 2001 10:48 AM 50 Pathfinder Radar Scanners Antenna Antenna Type Patch array Beam Width (nominal) 3.
81154_6.book Page 51 Wednesday, October 10, 2001 10:48 AM Appendix A: Specification 51 5S and 9S 48" Open Array Scanner Unit General Approvals CE - conforms to FCC - conforms to 1995/5/EC, EN60945 Part 80 (47CFR) and Part 2 (47CFR) Dimensions Pedestal: Array: 427 x 296 x 406 mm (16.8 x 10.5 x 16 in) 1306 mm (51.4 in) length Weight Pedestal: Array: 24 kg (53.0 lb) 6 kg (13.
81154_6.book Page 52 Wednesday, October 10, 2001 10:48 AM 52 Pathfinder Radar Scanners 9S Transmitter - 10 kW Input Voltage 16 - 44 V DC (from display unit) Power Consumption 11 W Standby 80 W Typical operation in light winds 95 W Max. operation in 50 Kt winds 140 W Max.
81154_6.book Page 53 Wednesday, October 10, 2001 10:48 AM Appendix A: Specification 53 Receiver IF Frequency 60 MHz (nominal) Receiver Characteristic Semi-log Receiver Noise Figure Less than 5 dB (including Low Noise Converter/Limiter & IF Receiver) Receiver Bandwidth 12/3/0.7/0.5 MHz Note: If the scanner is bought for use with an existing display, contact your dealer/service agent for the latest display software to ensure you can use all the open array scanner features.
81154_6.book Page 54 Wednesday, October 10, 2001 10:48 AM 54 Pathfinder Radar Scanners 7S and 11S 72" Open Array Scanner Unit General Approvals CE - conforms to FCC - conforms to 1995/5/EC, EN60945 Part 80 (47CFR) and Part 2 (47CFR) Dimensions Pedestal: Array: 427 x 296 x 406 mm (16.8 x 10.5 x 16 in) 1918 mm (75.5 in) length Weight Pedestal: Array: 24 kg (53.0 lb) 9.4 kg (20.
81154_6.book Page 55 Wednesday, October 10, 2001 10:48 AM Appendix A: Specification 55 11S Transmitter - 10 kW Input Voltage 20 - 44 V DC (from display unit) Power Consumption 11 W Standby 80 W Typical operation in light winds 117 W Max. operation in 50 Kt winds 179 W Max.
81154_6.book Page 56 Wednesday, October 10, 2001 10:48 AM 56 Pathfinder Radar Scanners Receiver IF Frequency 60 MHz (nominal) Receiver Characteristic Semi-log Receiver Noise Figure Less than 5 dB (including Low Noise Converter/Limiter & IF Receiver) Receiver Bandwidth 12/3/0.7/0.5 MHz Note: If the scanner is bought for use with an existing display, contact your dealer/service agent for the latest display software to ensure you can use all the open array scanner features.
81154_6.
81154_6.book Page ii Wednesday, October 10, 2001 10:48 AM ii Grounding 35 Typical System Diagram 1 Radome Scanner 18" iii, 1, 47 24" iii, 1, 49 Connections 22 Mounting 21 Rejoining Cables 11 Routine Checks 41 S Safety - and Servicing 41 Electromagnetic Energy i High Voltage i Navigation Aid ii Scanner i Connections 36 Location 5 Mounting on Power Boats 9 on Sailboats 9 Scanner.
