Release 9 a Series c Series e Series Installation and operation instructions English Date: 01-2014 Document number: 81337-9-EN © 2014 Raymarine UK Limited
Trademark and patents notice Autohelm, hsb2, RayTech Navigator, Sail Pilot, SeaTalk, SeaTalkNG, SeaTalkHS and Sportpilot are registered trademarks of Raymarine UK Limited. RayTalk, Seahawk, Smartpilot, Pathfinder and Raymarine are registered trademarks of Raymarine Holdings Limited. FLIR is a registered trademark of FLIR Systems, Inc. and/or its subsidiaries.
Contents Chapter 1 Important information.......................... 9 4.5 Network connections ............................................ 43 Certified Installation ..................................................... 9 TFT Displays ............................................................. 10 4.6 GPS connection ................................................... 49 Water ingress ............................................................ 10 Chart cards and memory cards..............................
8.6 Resetting your system .......................................... 98 16.7 Chart motion mode........................................... 159 Chapter 9 Document viewer application ........... 99 16.8 Chart views...................................................... 160 16.9 Chart display.................................................... 162 9.1 Document viewer overview ................................. 100 16.10 Overlays ........................................................
19.4 Radar range and image quality.......................... 219 Chapter 24 Fusion link application .................. 283 19.5 Target tracking ................................................. 221 19.6 Distances, range, and bearing........................... 223 24.1 Fusion link overview ......................................... 284 24.2 Media sources ................................................. 285 19.7 Radar mode and orientation.............................. 225 24.3 Browsing music.............
30.7 System data troubleshooting ............................. 346 30.8 Video troubleshooting ....................................... 347 30.9 Wi-Fi troubleshooting........................................ 348 30.10 Bluetooth troubleshooting ............................... 349 30.11 Touchscreen troubleshooting ........................... 350 30.12 Touchscreen alignment ................................... 351 30.13 Miscellaneous troubleshooting ........................ 352 Chapter 31 Technical support ......
Chapter 1: Important information Warning: Touchscreen display Certified Installation When exposed to prolonged periods of direct sunlight, the touchscreen display can get very hot. In such conditions, avoid using the touchscreen display or use the unit's physical keys and buttons instead if available. Raymarine recommends certified installation by a Raymarine approved installer. A certified installation qualifies for enhanced product warranty benefits.
TFT Displays The colors of the display may seem to vary when viewed against a colored background or in colored light. This is a perfectly normal effect that can be seen with all color Thin Film Transistor (TFT) displays. • Cables are not cut or extended, unless doing so is detailed in the installation manual.
Industry Canada (Français) Connections to other equipment Cet appareil est conforme aux normes d'exemption de licence RSS d'Industry Canada. Requirement for ferrites on non-Raymarine cables Son fonctionnement est soumis aux deux conditions suivantes: 1. cet appareil ne doit pas causer d'interférence, et If your Raymarine equipment is to be connected to other equipment using a cable not supplied by Raymarine, a suppression ferrite MUST always be attached to the cable near the Raymarine unit. 2.
a Series / c Series / e Series
Chapter 2: Document and product information Chapter contents • 2.1 Handbook information on page 14 • 2.2 Handbook illustrations on page 15 • 2.3 Handbook conventions on page 16 • 2.
2.1 Handbook information Description Part number a Series / c Series / e Series Installation and operation handbook 81337 e7 / e7D Mounting template 87137 e95 / e97 / c95 / c97 Mounting template 87144 • e Series e125 / e127 / c125 / c127 Mounting template 87145 About this handbook e165 Mounting template 87166 This handbook contains important information regarding your multifunction display.
2.2 Handbook illustrations The illustrations and screenshots used in this handbook may differ slightly from your display model. The illustration of the multifunction display below is used throughout this manual and unless otherwise stated can apply to all variants of multifunction display (i.e. New a series, New c Series and New e Series).
2.3 Handbook conventions The following conventions are used throughout this handbook when referring to: Type Icons Example Convention The term "select" is used in procedures involving icons to refer to the action of selecting an on-screen icon, either using touch or physical buttons: • Touch — Press your finger on the icon to select. • Physical buttons — Use the Joystick to highlight the icon and press the Ok button.
Waypoint (MOB) button / icon Depending on the multifunction display variant there will be either a Waypoint (MOB) button or an on-screen icon. WPT button • c Series • e Series • RMK-9 keypad WPT icons • a Series • gS Series Throughout this manual the term: Select WPT, refers to pressing the physical WPT button or pressing the on-screen WPT icon. Touch and non-touch operations This handbook applies to both touch and non-touch operations.
2.4 Product overview a6x Display variants a6x multifunction displays are available in the following variants: Non-sonar variant a65 (E70076) a65 Wi-Fi (E70162) Sonar variant a67 (E70077) a67 Wi-Fi (E70163) DownVision variant a68 (E70206) a68 Wi-Fi (E70207) Features • Bluetooth • Bluetooth • Internal GPS • Internal GPS • Wi-Fi Controls Multi-Touch touchscreen (HybridTouch when paired with a remote keypad.) Multi-Touch touchscreen (HybridTouch when paired with a remote keypad.
c Series sand e Series display variants The following c Series and e Series multifunction display variants are available Nonsonar Sonar Series e7 (E62354) e7D (E62355) e Series Controls Features • Bluetooth. HybridTouch (Touchscreen and physical buttons) • Wi-Fi • NMEA 0183 • NMEA 2000 (via SeaTalkng) • Internal GPS. • Video input. c95 (E70011) c97 (E70012) • Bluetooth. c Series Physical buttons only • Wi-Fi • NMEA 0183 • NMEA 2000 (via SeaTalkng) • Internal GPS. • Video input.
Touchscreen overview The touchscreen provides an alternative to using physical buttons to control your multifunction display. All functions can be accessed using the touchscreen Note: Raymarine strongly recommends that you familiarize yourself with touch operations while your vessel is anchored or moored. You may find it helpful to use the simulator mode (accessible from Homescreen > Set-up > System Settings) in these situations.
Chapter 3: Planning the installation Chapter contents • 3.1 System integration on page 22 • 3.2 Installation checklist on page 26 • 3.3 System Limits on page 26 • 3.4 Multiple data sources (MDS) overview on page 27 • 3.5 Identifying your display variant on page 27 • 3.6 Networking constraints on page 28 • 3.7 Typical systems on page 29 • 3.8 System protocols on page 31 • 3.9 Data master on page 32 • 3.10 New a Series parts supplied on page 32 • 3.
3.1 System integration Your multifunction display is compatible with a wide range of marine electronics devices. 1 2 3 5 4 Display True/App VMG 7 6 8 0 Tack 0 9 000 0 AUDIO 0 ANTENNA 0 17 00 0 NETWORK 10 11 18 12 13 19 15 14 20 21 INTCM 16 22 P OWER 0 23 24 D12244-4 The display uses a number of protocols to transfer data between the various devices in your system.
Item Device Type Maximum quantity Suitable Devices Connections 4 GPS (external) — Raymarine 1 Any combination of the following: SeaTalk, SeaTalkng, or NMEA 0183. • RS130. • Raystar125 GPS. • Raystar125+ GPS (via optional SeaTalk to SeaTalkng converter). 5 Instruments — Raymarine As determined by SeaTalkng bus bandwidth and power loading. SeaTalkng: SeaTalk, SeaTalkng. • ST70. • ST70+. • ST70+ keypads. • i50 Depth, Speed, or Tridata • i60 Wind, CH Wind • i70.
Item Device Type 10 Video / camera Maximum quantity Suitable Devices Connections • a Series = 0 Composite PAL or NTSC video source. BNC connectors. Third party IP camera Via SeaTalkhs network. • e7, e7D, c Series = 1 • e Series (excluding e7 and e7D) = 2 10 IP camera — third-party Multiple Note: Only 1 IP camera can be viewed at a time. Note: IP cameras must be able to assign IP address via DHCP and allow unauthenticated, anonymous ONVIF access.
Item Device Type Maximum quantity Suitable Devices Connections 17 Raymarine Sirius marine weather / satellite radio receiver (North America only) 1 SeaTalkhs: SeaTalkhs, SeaTalkng. • SR150. • SR100. • SR6. SeaTalkng: • SR50. 18 Additional multifunction display(s) — Raymarine 5 SeaTalkhs (recommended): SeaTalkhs. • a Series multifunction displays. • c Series multifunction displays. • e Series multifunction displays. • gS Series multifunction displays.
3.2 Installation checklist 3.3 System Limits Installation includes the following activities: The following limits apply to the number of system components that can be connected in a Raymarine multifunction display system. Installation Task 1 Plan your system. Component Maximum 2 Obtain all required equipment and tools. Site all equipment. Maximum number of SeaTalkhs devices 25 3 4 Route all cables. Maximum number of SeaTalkng devices 50 5 Drill cable and mounting holes.
3.4 Multiple data sources (MDS) overview Installations that include multiple instances of data sources can cause data conflicts. An example is an installation featuring more than one source of GPS data. 3.5 Identifying your display variant To discover which model display you have follow the steps below: MDS enables you to manage conflicts involving the following types of data: • GPS Position. • Heading. • Depth. • Speed. • Wind.
3.6 Networking constraints Product Image Raymarine’s 3rd generation LightHouse powered multifunction displays (a Series, c Series, e Series and gS Series) can be networked together. Multifunction display Generation C-Series Widescreen 2nd generation E-Series Classic 1st generation C-Series Classic 1st generation General • Multifunction displays should be connected together using SeaTalkhs.
3.7 Typical systems The illustrations below show examples of possible system configurations, for more details on compatible Raymarine devices please refer to the System integration section. Note: In the examples below the multifunction display(s) could be any variant of Raymarine’s 3rd generation multifunction displays e.g. a Series, c Series, e Series or gS Series. Example: Basic system 2 1 3 4 5 0 SeaTalkhs / RayNet 6 SeaTalkhs / RayNet SeaTalkng D12245-3 1. Multifunction display 2.
Example: Basic system with non-sonar variant display 2 1 3 4 5 0 SeaTalkhs / RayNet SeaTalkng D12590-2 1. Multifunction display 2. Sonar module 3. Sonar transducer 4. Evolution autopilot 5. SeaTalkng pilot controller Example: Expanded system 5 SeaTalkhs / RayNet 12 6 7 4 8 9 SeaTalkng 3 SeaTalkng 2 SeaTalkng 1 SeaTalkng 10 15 SeaTalkhs / RayNet 12 DeviceNet 14 12 13 11 SeaTalkhs / RayNet SeaTalkhs / RayNet SeaTalkhs / RayNet D12247-2 1. Radar scanner 2. Weather sensor 3.
3.8 System protocols Your Multifunction Display can connect to various instruments and displays to share information and so improve the functionality of the system. These connections may be made using a number of different protocols. Fast and accurate data collection and transfer is achieved by using a combination of the following data protocols: is generally used to connect a data receiver and a transmitter together, e.g. a compass sensor transmitting heading to a radar display.
3.9 Data master 3.10 New a Series parts supplied Any system containing more than one networked multifunction display must have a designated data master. The following items are supplied with your multifunction display. The data master is the display which serves as a primary source of data for all displays, it also handles all external sources of information.
3.11 e7 / e7D Parts supplied 3.12 New c Series and New e Series parts supplied The parts shown below are supplied with the e7 / e7D multifunction display. The parts shown below are supplied with the New c Series and New e Series (Excluding e7 and e7D) multifunction displays. 5 4 3 4 2 1 x4 x4 3 6 2 x4 9 5 6 1 7 7 8 D12170-4 D12248-2 1. Sun cover. 2. Front bezel. 3. Multifunction display. 4. Rear bezel (required for trunnion bracket mounting). 5. Gasket (required for flush mounting). 6.
3.13 Tools required for installation 3.14 Selecting a location Warning: Potential ignition source This product is NOT approved for use in hazardous/flammable atmospheres. Do NOT install in a hazardous/flammable atmosphere (such as in an engine room or near fuel tanks). 1 General location requirements 2 When selecting a location for your product it is important to consider a number of factors.
Vessel construction 1 2 6 250 (9.8 mm 4 in ) 200 (7.8 mm 7 in ) mm 500.7 in) 9 1 ( The construction of your vessel can have an impact on GPS performance. For example, the proximity of heavy structure such as a structural bulkhead, or the interior of larger vessels may result in a reduced GPS signal. Before locating equipment with an internal GPS antenna below decks, seek professional assistance and consider use of an external GPS antenna mounted above decks. Prevailing conditions mm 700.
a Series / c Series / e Series
Chapter 4: Cables and connections Chapter contents • 4.1 General cabling guidance on page 38 • 4.2 Connections overview on page 39 • 4.3 Power connection — New a Series on page 40 • 4.4 Power connection — New c Series and New e Series on page 41 • 4.5 Network connections on page 43 • 4.6 GPS connection on page 49 • 4.7 AIS connection on page 50 • 4.8 Fastheading connection on page 50 • 4.9 SeaTalkng connections on page 51 • 4.10 SeaTalk connection on page 51 • 4.
4.1 General cabling guidance Cable types and length It is important to use cables of the appropriate type and length • Unless otherwise stated use only standard cables of the correct type, supplied by Raymarine. • Ensure that any non-Raymarine cables are of the correct quality and gauge. For example, longer power cable runs may require larger wire gauges to minimize voltage drop along the run. Routing cables Cables must be routed correctly, to maximize performance and prolong cable life.
4.2 Connections overview 0 0 Details of the connections available on Raymarine multifunction displays are shown below.
0 4.3 Power connection — New a Series 4 1 0 0 0 • Cable must be of a suitable gauge for the circuit load. 0 • Each unit should have its own dedicated power cable wired back to the distribution panel. 2 3 5 Cable extension The following restrictions apply to any extension to the power cable: 6 D12581-2 1. Multifunction display rear panel connections. Total length (max) Supply voltage Cable gauge (AWG) 0–5 m (0–16.4 ft) 12 V 18 5–10 m (16.4–32.8 ft) 12 V 14 10–15 m (32.8–49.
2. Vessel power supply negative (-) 3. In-line fuse (If your products power cable does not have a built in fuse then an in-line fuse should be fitted.) 4.4 Power connection — New c Series and New e Series 4. * Drain wire 5. Product power cable 6. Vessel battery 7. * Vessel RF ground point connection Note: * Only applicable to products that include a drain wire on the product’s power cable.
Power cable - + 1 The display is supplied with a combined power and data multi cable, this can be extended if required. 2 Power cables available Cable Part number 1.5 m (4.9 ft) Straight power and data cable R62379 1.5 m (4.9 ft) Right angled power and data cable R70029 Notes 3 Cable extension The following restrictions apply to any extension to the power cable: 4 4 • Cable must be of a suitable gauge for the circuit load.
4.5 Network connections 3. RayNet cable. You can connect compatible devices to your multifunction display using the Network connector(s) at the rear of the unit. 4. RayNet radar cable. A typical network of digital devices may include: 5. VCM (Voltage Converter Module) — required for Open Arrays. • Up to 6 Raymarine multifunction displays. 6. Power connection. • RayNet or SeaTalkhs digital devices such as a sonar module and radar scanner.
1 2 3 4 D12254-1 1. Radar extension cable. 2. Radar power and data digital cable. 3. Raymarine network switch (or crossover coupler if connecting radar directly to display). 4. RayNet cable (or RayNet to SeaTalkhs cable if connecting via crossover coupler). Note: The extension cable connects to the radar scanner. Note: The power connection is NOT shown in the diagram. If using an Open Array scanner a VCM (Voltage Converter Module) must be connected between the scanner and the power supply.
marine electronics system. The sonar variant multifunction displays feature a built-in sonar, enabling you to connect the display directly to a compatible sonar transducer. Non-sonar variants require a connection to an external Raymarine sonar module. Internal and external sonars require a connection to a compatible sonar transducer. • Sonar transducer connection — provides sonar signals to the sonar module.
1. Rear connector panel of multifunction display (Non-sonar variant). T200 Series thermal camera connection 2 1 2. Raymarine network switch (only required if connecting more than one device using SeaTalkhs / RayNet). 3. RayNet cable. 4. Raymarine sonar module. 5. Sonar transducer cable. 4 3 5 6. Sonar transducer. D12839-1 Minn Kota sonar transducer connection via optional adaptor cable (Sonar variant multifunction displays only) 1. T200 Series fixed mount thermal camera. 2. Multifunction display.
Thermal camera cables Cabling requirements for thermal cameras. Camera to network switch 1 2 A network patch cable is required to connect the camera to the network switch. The connection is made between the camera cable tail and the network switch via the coupler (supplied with the camera). Network patch cables are available in a variety of lengths. 3 3 3 4 Joystick Control Unit (JCU) 3 4 An Ethernet (with power) cable is used to connect the JCU. The JCU is supplied with a 7.
Fusion link connection Network connection You can connect a Fusion 700 series marine entertainment system to your multifunction display. 2 1 Direct connection 3 3 4 4 5 2 1 D12741-1 6 1. Multifunction display. 2. Fusion system. 3. RayNet to SeaTalkhs cable. 4. Fusion ethernet connector. Direct connection with networked multifunction displays 1 3 2 6 D12740-1 4 1. Network switch. 2. Fusion system. 3. RayNet to SeaTalkhs cable. 4. Fusion ethernet connector. 5.
4.6 GPS connection Network connection 1 Depending on display variant, your multifunction display may include an internal GPS receiver. If required the multifunction display can also be connected to an external GPS receiver, using SeaTalkng or NMEA 0183. 2 3 GPS connection — SeaTalkng 1 4 2 SeaTalkng D12261-1 4 1. Multifunction display. 2. SeaTalkng GPS receiver. D12697-3 1. Network switch. GPS connection — NMEA 0183 2. Keypad. 3. Right angled power cable. 1 2 4.
4.7 AIS connection 4.8 Fastheading connection A compatible AIS can be connected using SeaTalkng or NMEA 0183. If you wish to use MARPA (radar target acquisition) functions on your multifunction display you need either: Connection using SeaTalkng • An autopilot connected to the multifunction display via SeaTalkng or NMEA 0183.
4.9 SeaTalkng connections 4.10 SeaTalk connection The display can connect to a SeaTalkng network. You can connect SeaTalk devices to your multifunction display using the optional SeaTalk to SeaTalkng converter.
4.11 a Series to NMEA 0183 DSC VHF radio connection The a Series multifunction display requires an NMEA 0183 to SeaTalkng converter and a powered SeaTalkng backbone to enable connection to an NMEA 0183 DSC VHF radio. 3 1 4 4.12 NMEA 0183 connection NMEA 0183 devices can be connected to New c Series and New e Series multifunction displays using the power and data cable. Note: New a Series does not support connection of NMEA 0183 devices.
Cable color Port Input / output Positive (+) / negative (-) * * Output Positive * * Output Negative 9 * * Input Positive 10 * * Input Negative * * Output Positive * * Output Negative Item 7 8 11 12 Device NMEA device NMEA device Note: *Refer to instructions provided with NMEA device. 4.13 NMEA 2000 connection The display can receive data from NMEA 2000 devices (e.g. data from compatible engines).
4.14 Camera / Video connection 4.15 Camera / video in-out connection A camera or a video device can be connected directly to New c Series and New e Series multifunction displays using the video connector on the power and data cable. A camera / video device or external display can be connected to New e Series multifunction displays (excluding the e7 / e7D) using the dedicated video in/out connector. Note: Video devices cannot be directly connected to New a Series multifunction displays.
Connector type BNC (female) Output resolution 720p You can use your multifunction display to wirelessly control a Bluetooth-compatible media player (such as a smartphone). The media player must be compatible with the Bluetooth 2.1+ EDR power class 1.5 (supported profile: AVRCP 1.0) or higher. Video cables The following video cable is required for the video in / out connector on the e95 / e97 / e125 / e127 variant multifunction displays.
select Ok on the multifunction display. If the code does NOT match, repeat steps 4 to 8. 11. If the pairing was successful the multifunction display will confirm the pairing. The external media device is now paired with the multifunction display. 1. 2. 3. 4. 5. 6. Select Set-up. Select System Settings. Select Wireless Connections. Select Connection Manager. Select the media player device in the list. Select Unpair / Forget this device. Enabling audio control With the homescreen displayed: 1.
4.17 Bluetooth remote control connection 9. When prompted, press the arrow button on your remote that you wish to be configured as the UP button. The other arrow button will automatically be configured as the DOWN button. If the pairing was successful a “Pairing Success” message will be displayed. If a “Pairing Failure” or “Pairing Timeout” message is displayed, repeat steps 1 to 8. You can control the multifunction display wirelessly using a Raymarine remote control unit.
4.18 Remote control functions Bu tto n s Arrow buttons Shortcut button Ra n g e or P a ir S e le c t D12051-2 Button Default functions: Range / zoom. Application where function available: Chart Radar Fishfinder Weather Homescreen • Press UP or DOWN arrow for momentary response. • Hold UP or DOWN arrow for continuous response. Open homescreen. Shortcut: Hold Select application in homescreen (in left-to-right, top-to-bottom order). • Press UP or DOWN arrow for momentary response.
Reconnecting the RCU 1. When you pair the RCU-3 with a multifunction display a wireless connection is established. 2. When you power off the multifunction display it loses its connection with the RCU-3 after 10 minutes. 60 5 55 10 50 15 45 40 Minutes 20 35 25 30 = > 10 Minutes 3. To restore the connection between the 2 units, press and hold any button on the RCU-3 for at least 3 seconds.
4.19 WiFi connections Raymarine mobile app connection You can use compatible tablet and smartphone devices as a wireless repeat display or remote control for your multifunction display. Raymarine apps allow you to stream and / or control, remotely what you see on your multifunction display to a compatible device, using a Wi-Fi connection. To use this feature you must first: • Ensure your device is compatible with the app you wish to use.
Chapter 5: Mounting Chapter contents • 5.1 Mounting - New a Series on page 62 • 5.
5.1 Mounting - New a Series 2. Drill or knock out the 4 mounting holes on the unit 0 Product dimensions D 00 E B C 0 0 0 D12588-1 F A D12579-2 Item a6x a7x A 163.6 mm (6.4 in.) 205.1 mm (8 in.) B 143.5 mm (5.6 in.) 147.1 mm (5.8 in.) C 17.5 mm (0.7 in.) 14.5 mm (0.57 in.) D 56.6 mm (2.2 in.) 59.1 mm (2.3 in.) E 162.4 mm (6.4 in.) 163.3 mm (6.4 in.) F 150 mm (5.9 in.) 150 mm (5.9 in.) 3.
display, ensuring that the clips along the bottom edge of the bezel latch into position. D12586-1 D12578-2 1. Mark the location of the mounting bracket screw holes on the chosen mounting surface. 2. Drill holes for the screws using a suitable drill, ensuring there is nothing behind the surface that may be damaged. 3. Use the fixings supplied with the mounting bracket to attach securely. 4. Attach the display to the mounting bracket. 4. Ensure the bezel is correctly aligned with the display, as shown. 5.
5.2 Mounting - New c Series and New e series Product dimensions C i. Outer edges - work from the sides upwards and then along the top edge, ensuring that the clips are fully released from the display. ii. Inner edges - ensure that the bezel is completely removed from the display. Note: Only the e7 and e7D have fixing screws for the rear bezel, other multifunction display variants have clips which hold the rear bezel in place. D E B Surface mounting The display can be surface mounted.
1. Remove the front bezel. Refer to the separate instructions provided for that procedure. 2. Place the bezel over the rear of the display, ensuring that it is correctly aligned with the display. Apply firm but even pressure to the bezel along the: i. Outer edges - work from the sides upwards and then along the top edge, to ensure that it clips securely into position. ii. Inner edges - ensure that the bezel sits flat against the unit. 2 1 e7 / e7D 3 D12273-2 D12183-3 3.
D12274-1 4. Ensure the bezel is correctly aligned with the display, as shown. 5. Apply firm but even pressure to the bezel along the: i. Outer edges - work from the sides upwards and then along the top edge, to ensure that it clips securely into position. ii. Inner edges - particularly along the chart card door edge, to ensure that the bezel sits flat. 6. Check that all control buttons are free to operate. Removing the front bezel Before proceeding ensure the memory card slot door is open.
Chapter 6: Getting started Chapter contents • 6.1 Display power on page 68 • 6.2 New a Series Controls on page 68 • 6.3 e7 / e7D Controls on page 69 • 6.4 c95 / c97 / c125 / c127 / e95 / e97 / e125 / e127 / e165 Controls on page 69 • 6.5 Homescreen overview — Touch only displays on page 71 • 6.6 Homescreen overview — c Series / e Series on page 71 • 6.7 Pages on page 73 • 6.8 Applications on page 75 • 6.9 Splitscreen controls on page 75 • 6.10 Screen overview on page 76 • 6.
6.1 Display power 6.2 New a Series Controls Powering the display on 1. Press the POWER button. 2. Select Accept to acknowledge the disclaimer message. 1 Powering the display on 1. Press the POWER button. 2. Press the OK button to accept the disclaimer message. 2 3 Powering the display off D12577-1 1. Press and hold the POWER button until the countdown reaches zero. Note: If the POWER button is released before the countdown reaches zero, the power off is cancelled.
6.3 e7 / e7D Controls 6.4 c95 / c97 / c125 / c127 / e95 / e97 / e125 / e127 / e165 Controls 1 2 1 2 3 3 4 4 5 5 6 6 7 7 D12179-1 Description Functions 1 Touchscreen you can touch the screen to operate many common functions, including all menu operations. 2 Menu Accesses menus. Press again to close menus. 3 UniControl Provides a joystick, rotary control and an OK push button for using menus and applications. 4 Back Press to return to a previous menu or dialog level.
List of cursor labels 1 2 3 Label Feature Application A/B Ruler line Chart AIS AIS target Chart COG Course Over Ground vector Chart CTR Center of radar Radar FLT Floating EBL/VRM Radar GRD Guard zone Radar HDG Heading vector Chart MARPA MARPA target Radar MOB Man Over Board marker Chart, Radar POS Vessel's position Chart RTE Route leg Chart SHM Ship's Heading Marker Radar TIDE Tide indicator Chart TRACK Track line Chart VRM/EBL VRM and EBL, 1 or 2 Radar WI
6.5 Homescreen overview — Touch only displays 6.6 Homescreen overview — c Series / e Series The Homescreen provides a central point of access for your display's applications, data and settings. The Homescreen provides a central point of access for your display's applications, data and settings. • The Homescreen provides quick access to your data (waypoints, routes, tracks, images and videos) and backup settings.
• Radar scanner. • AIS receiver / transceiver. Symbol • Sonar module. Radar power mode Off Scanner powered off when radar not required, but display is in use for other applications, such as the chart. When selected, the system counts down. During this time you cannot re-power the scanner. Timed Transmit Scanner switches between on/transmitting, and standby mode. Scanner goes into power save mode when constant use of radar is not required. • GPS receiver. • Autopilot.
6.7 Pages GPS status symbols The GPS receiver status is indicated in the databar. Symbol Description A GPS receiver is connected and has obtained a fix. A GPS receiver is not connected, or cannot obtain a fix. Pages are used to display applications. Pages are accessed using the icons on the Homescreen. Each page can display more than 1 application. • You can set up and display up to 4 applications per page using a c Series, e Series or gS Series (except for the e7 and e7D) multifunction display.
Changing an existing page on the homescreen With the homescreen displayed: 1. Select Customize. 2. Select Homescreen. 3. Select Edit Page. 4. Select the page icon that you want to change. The Customize menu options are displayed. 5. Select the appropriate page layout (for example, “Splitscreen”). 6. Select the application(s) you want to display on the page, either by selecting the relevant menu item or dragging it over to the displayed page. 7. Select Finish. The Rename Page dialog is displayed. 8.
6.8 Applications Chart application — provides a 2D or 3D graphical view of your charts to help you navigate. Waypoint, route, and track functions enable you to navigate to a specific location, build and navigate routes, or record where you've been. Chart cards provide higher levels of detail and 3D views. 6.9 Splitscreen controls When viewing a page with more than 1 application displayed you can switch applications from the splitscreen view to fullscreen view.
Selecting the active window — e7 / e7D 6.10 Screen overview When viewing a splitscreen page you can select the active application and view it fullscreen on an e7 / e7D with the touch lock enabled by following the steps below. 1 With a page featuring multiple applications displayed: 1. Press the Menu button. 2. Select Cycle application. Selecting cycle application cycles through the available applications. 3. Select Fullscreen to view the active application in fullscreen, or 4.
Screen item Description Screen item Description 1 Back — On displays with a touchscreen you can press the onscreen << (back) icon to go back to a previous menu. On non-touchscreen displays or HybridTouch displays use the Back button. 4 Close 2 Close — On displays with a touchscreen you can press the onscreen X (close) icon to go back to a previous menu. On non-touchscreen displays or HybridTouch displays use the Back button to back out of the menu structure.
Editing information in dialogs i. The Rotary control — Non-touchscreen or HybridTouch displays, or ii. The onscreen Up and Down arrows — Touchscreen displays. 3. To access the on-screen numeric keypad: With the dialog displayed: 1. Select the field you want to edit. The onscreen keyboard is displayed: • Touch operation — Select the onscreen keypad icon from the numeric adjust control. • Non-Touch operation — Press and hold the Ok button. The onscreen numeric keypad is displayed. 4.
6.11 Basic touchscreen operations Placing and moving the cursor using touch To place or move the cursor around the screen on a touchscreen multifunction display follow the steps below. 1. Touch the screen at any position on the screen to place the cursor there. Touchscreen lock 6.12 Multi-Touch gestures Raymarine a Series and gS Series multifunction displays support multi-touch. Multi-touch means that the display is capable of recognizing multiple simultaneous touch inputs.
6.13 Initial set up procedures Once your display has been installed and commissioned, Raymarine recommends that you perform an initial set up procedure. Startup wizard When you power-up the display for the first time or after a system reset a Startup Wizard is displayed. The wizard guides you through the following basic configuration settings: 1. Language 2. Vessel type 3. Units of measure 4. Total fuel capacity 5. Number of batteries 6. Number of engines 7.
1. Select Set-Up. 2. Select System Settings. 3. To enable the internal GPS, select Internal GPS so that On is highlighted. 4. To disable the internal GPS, select Internal GPS so that Off is highlighted. Simulator mode The Simulator mode enables you to practice operating your display without data from a GPS antenna, radar scanner, AIS unit, or fishfinder. The simulator mode is switched on / off in the System Setup Menu. Note: Raymarine recommends that you do NOT use the simulator mode whilst navigating.
6.15 Engine identification 5. Select OK on the Identify Engines confirmation dialog. Engine data can be shown on your multifunction display. The engines will now appear in the correct location on the engine data page. To enable engine data to be displayed you must connect your vessel’s engines CAN bus to your multifunction displays SeaTalkng bus. Depending on your engine and system type this may require the use of the Raymarine Engine & Control Interface (ECI).
6.16 Enabling AIS functions 6.17 Software updates Before proceeding ensure your AIS unit is connected to NMEA Port 1. Raymarine’s multifunction display software is updated regularly to provide new and enhanced features and improved performance and usability. You should ensure you have the latest software by regularly checking the Raymarine website for new software.
12. Insert the MicroSD card into the card reader of your multifunction display. After a few seconds your multifunction display will alert you that a software update is available and which multifunction displays and remote keypads require the update. The software alert is only displayed once per power cycle. 13. Select Yes to begin the software update. The following steps will now take place: 1.
Chapter 7: System checks Chapter contents • 7.1 GPS Check on page 86 • 7.2 Radar check on page 87 • 7.3 Sonar check on page 88 • 7.
7.1 GPS Check Checking GPS operation You can check that the GPS is functioning correctly using the chart application. 1. Select the Chart page. Item Description 1 Sky view — a visual representation of the position of tracked satellites. 2 Satellite status — displays the signal strength and status of each satellite identified in the sky view diagram on the left of the screen. The colored bars have the following meanings: • Grey = searching for satellite. • Green = satellite in use.
7.2 Radar check Example misaligned radar Warning: Radar scanner safety 1 2 Before rotating the radar scanner, ensure all personnel are clear. Warning: Radar transmission safety The radar scanner transmits electromagnetic energy. Ensure all personnel are clear of the scanner when the radar is transmitting. Checking the radar From the Radar application: 1. Select Menu. 2. Select Power so that On is highlighted. The Radar scanner will now initialize in standby mode.
7.3 Sonar check 5. Select your speed transducer from the list. Sonar transducer and sonar module selection Checking the sonar You must select the sonar transducer and Sonar module that you want to use. Sonar checks are made using the fishfinder application. 1. Select a fishfinder page from the Homescreen. Sonar module selection • Sonar and DownVisionTM variant displays are fitted with an internal sonar module. • All variants allow you to connect a compatible external sonar module.
2. Select Set-up. 3. Select Transducer Set-up. 4. Select Depth Offset. The depth offset numeric adjust control is displayed. 5. Adjust the offset to the required value. Setting the speed offset From the fishfinder application: 1. Select Menu. 2. Select Set-up. 3. Select Transducer Set-up. 4. Select Speed Offset. The speed offset numeric adjust control is displayed. 5. Adjust the offset to the required value. Setting the Temperature offset 1. 2. 3. 4. Select Menu. Select Set-up. Select Transducer Set-up.
Resetting the thermal camera to the home position When connected to a pan, tilt thermal camera the home position of the camera can be set. In the thermal camera application: 1. Select Menu. 2. Select Camera Home. The camera returns to its currently defined home position, and the “Home” icon appears on-screen momentarily.
Chapter 8: Managing display data Chapter contents • 8.1 Memory cards overview on page 92 • 8.2 a Series on page 92 • 8.3 c and e Series on page 93 • 8.4 Saving user data and user settings on page 94 • 8.5 Screenshots on page 98 • 8.
8.1 Memory cards overview 8.2 a Series You can use MicroSD memory cards to archive data (e.g. waypoints and tracks). Inserting a memory card or chart card MicroSD memory cards can be used to archive your data when the system capacity is reached. You can then delete old data from your system, creating capacity for new data. The archived data can be retrieved at any time. You can also use memory cards to backup your data. 1. Open the card reader door, located on the front right of the display. 2.
8.3 c and e Series Inserting a memory card or chart card 1. Open the chart card door, located on the front right of the display. 2. Insert the card, as shown in the diagram below. For slot 1, the card contacts should be facing DOWN. For slot 2, the card contacts should be facing UP. Do NOT force the card. If the card does not fit easily into the slot, check the orientation. D12290-1 3. Gently press the card all the way in to the card slot, as shown in the diagram below.
8.4 Saving user data and user settings You can save your waypoints, routes, tracks and user settings to a memory card. Waypoints, routes and tracks are saved as gpx data files. The gpx file format is a device-independent data format making it easy to exchange data between your display and other GPS devices / software that support the gpx file format.
1. Ensure you have a memory card (NOT a chart card) inserted into a card slot. 2. Select My Data. 3. Select Import/Export. 4. Select Save Data to Card. 5. Select Save Tracks to Card. The Tracks list is displayed. 6. Select the group or groups you want to save, or select Select All. 7. Select Save. The on-screen keyboard is displayed. 8. Using the on-screen keyboard enter the filename you want to save the file as. 9. Select SAVE.
1. Ensure you have the memory card containing the data in one of the card slots. 2. Select My Data. 3. Select Import/Export. 4. Select Erase from Card. The file browser is opened. want to retrieve settings from, if your display only has 1 card slot then you will not be prompted. 5. Select SD1 for a memory card in the top card slot, or SD2 for a memory card in the bottom card slot. A confirmation dialog is displayed. 6. Select OK.
Alarms Radar application Application Setting Application Setting Alarms Anchor alarm Radar Select scanner Timer Alarm clock Temperature alarm Arrival alarm Range rings AIS Layer Application Setting AIS Layer Displayed target types Offtrack alarm AIS safety messages Collision alarm Buddy tracking Guard zone sensitivity Silent mode Fish alarm Fish alarm depth limit Data application Shallow depth alarm Application Setting Deep depth alarm Data Datapages and content Datapage order A
8.5 Screenshots 8.6 Resetting your system You can take a screenshot of what is currently displayed on the screen. Your system may be reset to its factory default settings if required. Screenshots are saved to a MicroSD card in .bmp (bitmap) format. The saved image can be viewed from any device capable of viewing bitmap images. There are 2 types of reset operation, both of which affect the current display you are using, AND any networked displays. Taking a screenshot • Settings and data reset.
Chapter 9: Document viewer application Chapter contents • 9.
9.1 Document viewer overview • Fit to Width — Scales the open document to fit the width of the application window. Your multifunction display includes a pdf document viewer. The document viewer is available from the homescreen and is used to view and search pdf documents (such as product handbooks). • Close File — Closes the open document. Opening the user manual The product user manual is stored on the internal memory. From the homescreen: 1. Select Doc Viewer. 2. Select User Manual.
Note: You can also use the scroll bars to navigate through the document. • You may see a ‘Searching’ icon while all occurrences are found. • The find tool bar is displayed. Browsing an open document On HybridTouch and non-touch displays you can browse pdf documents by following the steps below. With a pdf document open: 1. Move the Joystick Up or Down to move up and down through the document. 2. Move the Joystick Left or Right to pan left and right. • The first occurrence of the keyword is highlighted.
a Series / c Series / e Series
Chapter 10: Autopilot control Chapter contents • 10.1 Autopilot control on page 104 • 10.2 Pilot Bar on page 106 • 10.3 Pilot Set-up on page 107 • 10.4 Pilot settings on page 107 • 10.5 Autopilot status symbols on page 112 • 10.
10.1 Autopilot control You can use your multifunction display to control your autopilot. If connected to an Evolution autopilot then pilot settings will also be available. Note: For information on connecting your multifunction display to a Raymarine autopilot system, refer to the documentation that accompanied your autopilot. With the Autopilot Control function enabled, you can use your multifunction display to: • Engage the autopilot in Track mode (Goto a specified position or follow a route).
Enabling autopilot control Enabling the autopilot control function — SeaTalk and SPX SeaTalkng autopilots To enable control of your SeaTalk or SPX SeaTalkng autopilot using your multifunction display follow the steps below. From the Homescreen: 1. Select Set-up. 2. Select System Settings. 3. Select Autopilot Control so that On is highlighted. Selecting Autopilot Control will switch the control between On and Off.
1. Select any of the following options from the Chart context menu: 10.2 Pilot Bar • Goto Cursor The Pilot Bar provides autopilot status information. For touchscreen displays you can disengage the autopilot using the Pilot Bar. • Follow Route Pilot Bar — Track mode • Goto Waypoint • Follow from Here • Follow Route in Reverse The pilot control dialog is displayed. 2. Select Yes (Track).
10.3 Pilot Set-up 10.4 Pilot settings When connected to an Evolution autopilot the Pilot Set-up page is available. The Pilot settings option is available on a data master multifunction display when it is integrated with an Evolution autopilot. The Pilot settings enable the setup and commissioning of an Evolution autopilot using a multifunction display.
Selecting a drive type • Rudder Limit. Drive type selection is available from the dockside wizard, and also from the Vessel settings menu: Pilot Set-up > Pilot Settings > Vessel Type > Drive type. • Hard Over Time. With the Drive Type menu displayed: 1. Select your drive type from the list. Note: *The rudder damping setting should not be adjusted without first seeking advice from Raymarine technical support. Setting the auto turn angle Note: The drive types available are dependant on the ACU type.
Setting the rudder limits On vessels fitted with a rudder reference transducer the rudder limits must be set. The rudder limit is used to set the rudder control. The rudder limits should be set to just inside the mechanical end stops to prevent unnecessary load on the steering system. Note: This procedure is not required on vessels without a rudder reference transducer.
• For vessels without a rudder reference transducer — A default of 30 degrees is displayed, and can be changed as required. Hard over time The following Dockside wizard procedures only apply to vessels without a rudder reference transducer: • Drive Type selection. • Rudder Limit setting. • Hard-over time setting (Raymarine recommends that this information is specified once the dockside wizard and Rudder Drive check is complete, using the Hard Over Time menu option).
Adjusting the hard-over time On vessels without a rudder reference transducer, it is important to set the hard-over time limits correctly, to ensure accurate autopilot operation. Hard-over time is the time it takes the vessel’s steering system to drive the rudder from full port to full starboard. Before attempting the following procedure, ensure that you’ve observed and understood the Rudder check warning provided in this document.
10.5 Autopilot status symbols 10.6 Autopilot alarms The autopilot status is indicated in the databar. The autopilot function provides alarms to alert you to situations that require action. Symbol Description Autopilot is in Standby mode. Autopilot is in Track mode. Autopilot is in Auto mode. No autopilot detected. Autopilot alarm active. Dodge mode is active. Fish mode is active. Your multifunction display shows autopilot alarms, regardless of whether there is active navigation on the system.
Chapter 11: Alarms and Man over board functions Chapter contents • 11.1 Using Man Overboard (MOB) functions on page 114 • 11.
11.1 Using Man Overboard (MOB) functions 1. Select Ok on the MOB alarm dialog. The alarm will be silenced but remains active. Man overboard Cancelling the man overboard (MOB) alarm — Touch only display If you lose a person or object overboard, you can use the Man Overboard (MOB) function to mark the position that the vessel was at when the MOB function was activated. The MOB function is available at all times, regardless of which application is running. MOB can be set to Dead Reckoning or Position mode.
11.2 Alarms Alarms alert you to a situation or hazard requiring your attention. You can set up alarms to alert you to certain conditions, such as collision warnings and temperature limits. Alarms are raised by system functions, and also external equipment connected to your multifunction display. When an alarm sounds a message dialog is displayed on your multifunction display and any networked displays. The dialog states the reason for the alarm.
Alarms menu Menu item Description Options MOB Data Type Determines whether Position or Dead Reckoning (DR) data is displayed. Assuming that your vessel and the MOB are subject to the same tide and wind effects, the Dead Reckoning setting normally gives a more accurate course. • Dead Reckoning When set to On, an alarm is triggered at the time you specify for the Alarm Clock Time setting. Alarm Clock Alarm Clock • Position (default) • Off (default) • On Alarm Clock Time • 00:00 (default) • 00.
Menu item Description Options • Deep Fish Limit — Specifies the upper value for the Fish Alarm Depth Limit. • 2 ft (or equivalent units) to the maximum of the transducer range Deep Fish Limit • 2 ft (or equivalent units) to the maximum of the transducer range Fuel Manager In the fuel manager alarm options you can switch the low fuel warning alarm on or off and specify the fuel level at which the alarm is triggered.
a Series / c Series / e Series
Chapter 12: DSC VHF radio integration Chapter contents • 12.1 DSC VHF radio integration on page 120 • 12.
12.1 DSC VHF radio integration You can connect your DSC VHF radio to your multifunction display and show distress message information and GPS position data for other vessels. Connecting a DSC VHF radio to your multifunction display provides the following additional functionality: • Distress Messages — when your DSC VHF radio receives a DSC message or alarm from another DSC VHF radio, the vessel identification (MMSI), GPS position, and time of distress message is displayed on your multifunction display.
Chapter 13: Fuel manager Chapter contents • 13.
13.1 Fuel manager overview Note: The fuel manager provides an estimate of fuel remaining, and the distance and time which can be travelled before the tanks are empty. In order to calculate these values, you must configure the total capacity of fuel available to the engines and log each time you add fuel. The fuel manager also allows you to set a low fuel warning alarm which is sounded when the vessel's estimated fuel falls below a specified value.
Fuel logging You must ensure all fuel fills are recorded using the fuel manager. From the fuel manager page: 1. When filling the tanks until full select All tanks full. The estimated fuel remaining is reset to the value of your fuel tanks capacity. 2. When only partially filling the tank make a note of the volume of fuel added to the tank and then select Add partial fill. 3. Enter the value noted earlier this will be added to your current fuel remaining figure.
a Series / c Series / e Series
Chapter 14: AIS function Chapter contents • 14.1 AIS overview on page 126 • 14.2 AIS prerequisites on page 127 • 14.3 AIS context menu on page 127 • 14.4 Enabling AIS on page 128 • 14.5 Displaying AIS vectors on page 128 • 14.6 AIS status symbols on page 129 • 14.7 AIS silent mode on page 129 • 14.8 AIS target symbols on page 130 • 14.9 Displaying detailed AIS target information on page 130 • 14.10 Viewing all AIS targets on page 131 • 14.
14.1 AIS overview AIS Simulator Mode The AIS feature enables you to receive information broadcast by other vessels, and to add these vessels as targets in the chart and radar applications. With an optional AIS unit connected to your system you can: • Display targets for any other AIS-equipped vessels. • Display voyage information being broadcast by these targets, such as their position, course, speed and rate-of-turn.
14.2 AIS prerequisites 14.3 AIS context menu You must have suitable AIS hardware connected to your multifunction display to make use of the AIS functionality. The AIS function includes a context menu which provides AIS target information and menu items. In order to run AIS, you will need: • A receive-only AIS unit or a full AIS transceiver (a unit that sends and receives). • A VHF antenna. • A GPS - to provide position data. • The AIS layer enabled in the chart or radar application, as appropriate.
14.4 Enabling AIS 14.5 Displaying AIS vectors Enabling AIS in the Chart application You must have the correct data available before AIS vectors can be displayed. To enable the AIS overlay in the Chart application follow the steps below. A target is defined as active when it has the following data displayed graphically: To enable the AIS overlay your system must include an AIS receiver or transceiver. The AIS overlay is not available in 3D view.
14.6 AIS status symbols 14.7 AIS silent mode AIS status is indicated by a symbol in the databar. AIS silent mode enables you to disable AIS transmissions Symbol Description AIS unit is switched on and operating. AIS currently unavailable. AIS unit is switched off, or not connected. AIS unit is in Silent Mode. AIS unit is in Silent Mode, with active alarms. AIS unit is connected and switched on, but has active alarms.
14.8 AIS target symbols Your multifunction display shows a range of symbols to represent the different types of AIS target. Target type Description Transmitting target Target is moving or at anchor (Target is not activated, dangerous or lost). Activated target Target activated — that is, AIS vector displayed. Vector line (optional) shows predicted distance travelled within a given time. Selected target Target selected with cursor. Can view detailed data. Symbol 14.
14.10 Viewing all AIS targets 14.11 Using AIS to avoid collisions • From the Chart application with only the AIS overlay enabled go to: Menu > AIS Options > Targets > View AIS List You can use the AIS safe zone and safety message functions to help you avoid collisions with other vessels and objects. • From the Chart application when the Radar overlay is also enabled go to: Menu > Radar & AIS Options > Targets > View Targets Lists > View AIS List.
5. Select Safety Messages. Selecting Safety Messages will switch between safety messages On and Off. Note: *When Radar overlay is also enabled the menu name becomes Radar & AIS Options. ** Step 3 is only required when Radar overlay is enabled. Enabling and disabling AIS safety messages in the radar application From in the radar application: 1. Select Menu. 2. Select Targets. 3. Select AIS Set-up. 4. Select Safety Messages. Selecting Safety Messages will switch between safety messages On and Off.
14.12 Target options The Target options menu for the Chart application and Radar application are shown below. Parameter Description Options Vector Length The length of the vector lines displayed depends on the distance that an AIS target travels in the time period that you specify for this setting. • 0.5 min • 1 min • 3 min • 6 min • 12 min • 30 min • 60 min Target History Targets’ previous position will be plotted as a target icon with lighter shading than the actual target for the time specified.
14.13 AIS alarms 14.14 Buddy tracking The AIS functions generate a number of alarms to alert you to dangerous or lost targets. The Buddy Tracking feature enables you to add AIS-equipped friends and regular contacts to a “Buddy List” on your multifunction display. As soon as a vessel on your Buddy List sails into the range of your AIS unit, the vessel icon changes to indicate this. In addition to the dangerous target alarm, the system generates an alarm when a dangerous target becomes a lost target i.e.
1. Select the AIS target. The AIS target context menu is displayed. 2. Select Add Buddy. i. Select Yes to enter a name for the buddy vessel ii. Select No to save the vessel to your buddy list without entering a name for the buddy vessel. The vessel will now be added to your buddy directory. Adding an AIS buddy from the AIS target list The AIS target list can be accessed from: • the Chart application with only the AIS overlay enabled: Menu > AIS Options > Targets > View AIS List.
a Series / c Series / e Series
Chapter 15: Waypoints, Routes and Tracks Chapter contents • 15.1 Waypoints overview on page 138 • 15.2 Routes on page 145 • 15.3 Tracks on page 148 • 15.4 Import and Export on page 149 • 15.
15.1 Waypoints overview Waypoints are position markers used for the purposes of navigation. Your multifunction display can create waypoints, which can then be selected for active navigation. There are a range of features for placing, navigating and managing waypoints, these can be accessed from the Waypoints menu and Waypoint context menu. Waypoints are represented on-screen using customizable waypoint symbols. Waypoint can be created, moved, deleted, exported to memory card or imported from a memory card.
• Slew thermal camera (only available when thermal camera is connected and operating.) For active waypoints the following menu items are available: • Stop Goto • Restart XTE • Advance Waypoint • Measure Placing a waypoint From the chart, radar or fishfinder application: 1. Position the cursor at the required position. 2. Press the WPT button. The context menu is displayed. 3. Select Place Waypoint. The Waypoint Saved dialog is displayed.
Placing a waypoint at a known position You can place a waypoint at a specified location using latitude and longitude coordinates: 1. Select WPT. 2. Select Place Waypoint At Lat/Lon. The waypoint details dialog is displayed. 9. Show/Hide — You can choose which waypoint groups are displayed and which groups are hidden by selecting the relevant group from the list and then selecting Show/Hide. Selecting a waypoints group from the list displays a list of all waypoints in that group.
2. Select Assign Symbol. A list of all available symbols is displayed. 3. Select the symbol that you want to use for the waypoints in the selected group. A confirmation dialog is displayed. 4. Select Yes to apply the new symbols to the waypoints, or select No to cancel. Moving a waypoint to a different group With the Waypoints group list displayed: 1. Select ALL WAYPOINTS. A list of all waypoints currently on your system is displayed. 2. Select the waypoint you want to move.
Moving waypoints Waypoints can be searched for by: Moving a waypoint using the context menu • Name or keyword With the application page displayed: 1. Select the waypoint symbol on-screen. The waypoint context menu is displayed. 2. Select Move Waypoint. 3. Select the new position for the waypoint. • Symbol • Area Moving a waypoint by entering new coordinates With the Waypoint List displayed: 1. Select All Waypoints. 2. Select the relevant waypoint. The waypoint information page is displayed. 3.
9. Select Erase Wpts to erase the list of waypoints from your system, or 10. Select Move Wpts to move the waypoints to a new or existing group, or 11. Select Assign Symbol to assign a new symbol to all the waypoints in the search results list. You can also select a waypoint from the list to view its details, set a goto or display the waypoint in the Chart application. Waypoint symbols A Range of waypoint symbols are available that can be used to represent different waypoint types. 4.
Red racemark anti-clockwise Red Racemark clockwise Rocks Reef Marker Restriction Private Reef Public Reef Bottom Mark Top Mark Dolphin Shark Route Start Route End Billfish Tank Diver Down Diver Down 2 Reef Ball Sailboat Oil Rig Filled Circle Sportsfisher Trawler FAD (Fish Attracting Device) Concrete Rubble Swimmer Martini Seaweed Oyster Tree Tower Green Can Green Nun Hill or Peak Bridge Red Can Red Nun Airplane Car Yellow Can Yellow Nun Skull Diamond T Fish Trap
In the example above the Day Trip group will not be displayed in the Chart application. 3. Select Sort by: to switch between Groups and Symbols. A list of Symbols or Groups is displayed. 4. Select the Group or Symbol from the list that you want to show or hide. 15.2 Routes A route is a series of waypoints typically used to assist with passage planning and navigation. A route is displayed on screen as a series of waypoints linked by a line.
2. Select Build Route. The build route menu is displayed. 3. Select a location on screen to be the starting position. 4. Select relevant locations to place subsequent waypoints in order. The route is saved and displayed as each waypoint is placed. 5. When complete select Finish Build. The finish route build pop up message is displayed. 6. Select Follow to immediately follow the route. or 7. Select Edit to change the route name or change the route color. or 8.
Showing or hiding routes and tracks Erasing all routes From the chart application: 1. Select Menu. 2. Select My Data. 3. Select Routes or Tracks. 4. Select Show/Hide. 5. Select the route or track to switch between Show and Hide. From the homescreen: 1. Select My Data. 2. Select Import/Export. 3. Select Erase from System. 4. Select Erase Routes from System. The erase routes from system dialog is displayed. 5. Select Erase All. The confirm delete dialog is displayed. 6.
15.3 Tracks A track is an on-screen trail that shows the passage you have taken. This trail is made up of a series of track points which are created automatically. You can save the track to create a permanent record of where you have been • Auto— The track interval is automatically set (Auto will minimize track points whilst maintaining correlation between the track and the actual path followed). • Time— The track points are placed at regular intervals of time.
You can also edit track details by selecting Edit Track from the track context menu. Erasing tracks Erasing a track From the My Data menu: 1. Select Tracks. The track list is displayed. 2. Select the track you want to erase. 3. Select Erase Track. The erase track pop up message is displayed. 4. Select Yes to confirm, or No to cancel the action. 15.4 Import and Export Waypoints, Routes and Tracks can be imported and exported using a memory card.
15.
Chapter 16: Chart application Chapter contents • 16.1 Chart application overview on page 152 • 16.2 Navigation options on page 155 • 16.3 Chart ranging and panning on page 157 • 16.4 Chart selection on page 157 • 16.5 Vessel position on the chart display on page 158 • 16.6 Chart orientation on page 158 • 16.7 Chart motion mode on page 159 • 16.8 Chart views on page 160 • 16.9 Chart display on page 162 • 16.10 Overlays on page 163 • 16.11 Chart vectors on page 168 • 16.
16.1 Chart application overview The chart application provides route planning and navigation features. The Chart application is pre-loaded with a basic world base map. Compatible electronic charts can be used to expand the information and detail regarding your surroundings and charted objects. Depending on cartography type the chart application can be set to 2D or 3D view. • If you have a Raymarine GPS receiver using NMEA0183, or a third-party GPS receiver, you must correlate it separately.
Vector charts Vector charts are computer generated, consisting of a series of points and lines that make up the chart. Chart objects and overlays on vector charts can be switched on and off and chart objects can be selected to provide further information. Ranging in and out of vector charts will make geographical features appear larger or smaller on the screen, however text and chart objects will remain the same size regardless of range.
Unzipping files to memory card The LightHouse charts download file must be unzipped / extracted to memory card for use on your multifunction display. 6. Check that the files have been successfully placed on your memory card by viewing its contents in your file browser. Note: The instructions below are provided for guidance only. Depending on your PC’s operating system and the archiving (zip) software in use the steps required may differ slightly from those shown below.
Chart context menu The Chart context menu provides the cursors positional data and shortcuts to menu options. 16.2 Navigation options The chart application provides features to help navigate to a chosen location. The navigation options are found in the Navigate menu: Menu > Navigate • Pilot Controls — Accesses the Pilot Control Dialog, when Autopilot Control is enabled. • Goto Cursor — Will set the cursor position as the active destination.
2. Select Goto Cursor. Navigating to the cursor position on the chart using the menu D12295-1 You can also reset the XTE from the Navigate Menu: Menu > Navigate > Restart XTE. D11764-2 From the chart application: 1. Position the cursor at the desired destination on the chart. 2. Select Menu. 3. Select Navigate. 4. Select Goto Cursor. Navigating a route You can follow any route stored on the display. When following a route you visit each waypoint in order.
16.3 Chart ranging and panning 16.4 Chart selection Ranging in and out You can select the cartography type to be used in the Chart application. The Chart selection applies to the active Chart instance. You must have the necessary cartography chart cards inserted into your multifunction display in order to display different cartography type. The table below shows the Range controls available for each display variant.
16.5 Vessel position on the chart display Your current position is represented on-screen by the vessel symbol. The vessel symbols are only displayed when heading or COG data is available. The vessel symbol varies depending on selected settings and the availability of heading data. Motor Vessel The motor vessel symbol is used when the vessel type selected during the initial set up wizard is a motor vessel.
3. Bearing to waypoint. 4. Instantaneous heading. If heading data becomes unavailable whilst in this mode, a warning pop up message is displayed and the chart uses 0° heading in relative motion. Setting the chart orientation From the chart application menu: 1. Select Presentation. 2. Select View & Motion. 3. Select Chart Orientation. 4. Select Head Up, North Up, or Course Up option, as appropriate. Once selected the screen will update to reflect the new orientation. 16.
16.8 Chart views True Motion If supported by your cartography type, the Chart application can be set to either 2D or 3D view. Selecting 2D and 3D chart views D12304-1 When the motion mode is set to True Motion, the chart is fixed and the vessel moves in true perspective to fixed landmasses on-screen. As the vessel’s position approaches the edge of the screen, the chart picture is automatically reset to reveal the area ahead of the vessel.
3D chart view ii. HybridTouch or Touch only displays — Swipe your finger up or down across the screen to adjust the pitch. The 3D view can display a range of information to help you navigate. 1 2 3 4 5 6 7 8 10 D11755-1 9 000°T 11 12 13 14 D12307-2 Description 1 Range — horizontal chart scale indicator (shown in selected system units). 2 Depth Scale — approximate depth beneath your vessel (optional). 3 Waypoint — optional.
2. Select View & Motion. 3. Select 3D Display Options. 4. Select Transducer Cone so that On is highlighted. Selecting Transducer cone will switch the function on and off. Enabling depth scale In 3D view, to enable a depth indicator at your vessel’s location follow the steps below. From the Chart application menu: 1. Select Presentation. 2. Select View & Motion. 3. Select 3D Display Options. 4. Select Depth Scale: so that On is highlighted. Selecting depth scale will switch depth indicator on and off. 16.
16.10 Overlays The chart has a number of overlays that display different views and information. The overlays require electronic charts with the appropriate feature support and may also require additional hardware and service subscriptions. You can overlay the following data onto a 2D chart to give greater depth of information. The overlays available are: • * AIS — View and track AIS targets. This overlay is not available in 3D view. • * Radar — Overlay radar onto the chart.
Aerial photo overlay Your electronic charts may include aerial photography. Note: The NOWRad weather overlay can only be used in North America and its coastal waters. Enabling NOWRad weather overlay on the chart In 1. 2. 3. 4. the 2D chart view: Select Menu. Select Presentation. Select Overlays. Select NOWRad. The NOWRad opacity slider bar control is displayed showing the current opacity percentage. 5. Adjust the slider bar to the required opacity, or 6. Select Off to turn the NOWRad overlay off.
Community layer If supported by your cartography type, you can display User Generated Content (UGC) on the Chart application. 1 2 By default the Chart grid is switched off. Switching the chart grid on and off The Chart grid can be switched on and off by following the steps below. From the Chart application menu: 1. Select Presentation. 2. Select Overlays. 3. Select Chart Grid: so that On is selected to turn the grid on, or 4. Select Chart Grid: so that Off is selected to turn the grid off.
Chart boundaries Safe Zone Ring Chart boundary lines can be shown on-screen, these lines indicate the boundary of the cartography currently in use. The chart application can display and configure a MARPA / AIS safe zone ring. 1 2 The safe zone ring shares its configuration with the Radar applications safe zone ring, however can be displayed independently of the safe zone ring in the Radar application. 1. Chart boundaries On.
Fuel range rings The fuel range ring gives an estimated range that can be reached with the estimated fuel remaining on-board. 4. Select Boat Size: so that Small is selected to show the small vessel symbol. Displaying waypoint names Waypoint names can be shown next to their respective waypoint symbols. The fuel range ring can be displayed graphically in the chart application and indicates an estimated range that can be reached with the: From the Chart application menu. 1. Select Presentation. 2.
16.11 Chart vectors 16.12 Cartography objects Chart vectors are available for heading, COG, wind direction and tide direction. Chart vectors are only available in 2D view. Chart detail A range of vector graphics can be displayed in the chart application when in 2D chart view. The following vectors can be independently enabled or disabled: The chart detail setting determines the amount of detail shown in the Chart application.
Cartography objects If supported by you cartography type, cartographic objects can be individually switched on and off. The table below show a list of these objects. The Objects menu is accessed from: Menu > Presentation > Objects. Note: The Objects menu is only available when the cartography in use supports these features. Object (Menu item) Description Options Show Rocks Determines the depth at which rocks are displayed in the chart application.
16.13 Object information If supported by your cartography type, you can view detailed information about specific cartographic objects. 1. Select a location on screen. The chart context menu is displayed. 2. Select Find Nearest. A list of chart object types is displayed. 3. Select the chart object or service in the list. A list is displayed of the available instances of that particular object or service. 4. Select the item that you want to find.
When you select Animate the animate menu is displayed and the diamond-shaped current symbols are replaced with dynamic current arrows which indicate the direction and strength of the currents: Current graphs Current graphs provide a graphical view of current activity. 1 2 3 4 Current animation. 10 5 • Arrows indicate the direction of current flows. • The length of the arrow indicates the flow rate. • The color of the arrow indicates the flow speed: – Red: increasing current flow speed.
The animation can be viewed continuously or incrementally at a time interval that you specify. You can also set the date for the animation, and start or restart the animation at any point within a 24-hour period. If the system does not have a valid date and time the date used will be midday for the system default date. Note: Not all electronic charts support the animated tides feature. Check the Navionics website: www.navionics.com to ensure the features are available on your chosen cartography level.
16.14 Depth soundings and contours If supported by your cartography type, depth soundings and contours can be used in the Chart application to provide awareness of water depth. When using vector based cartography you can adjust the depth at which the contours and soundings appear on-screen. 3 1 2 D13009-1 1. Shallow contour 2. Safety contour 3. Deep contour The Depth & Contours menu can be accessed from: Menu > Presentation > Depth & Contours.
Depth & Contour options If supported by your cartography type, the following depth and contour settings are available. Note: The menu items available are dependant upon your cartography type. The depth options are dependant upon the units of measure in use on your system. Menu item Cartography type Description Options Show Soundings LightHouse vector charts and Navionics Determines the depth at which depth soundings are displayed.
16.15 My Data options 16.16 Multiple chart synchronization The My Data menu provides access to your user data. You can synchronize the heading, range, and position information across multiple chart views and networked displays. The options are found in the My Data menu: Menu > My Data. • Waypoints — View the waypoints group list. • Routes — View the Routes list. • Tracks — View the Tracks list. Refer to Chapter 15 Waypoints, Routes and Tracks for further details.
16.17 Measuring distances and bearings 2. Select Measure. You can now reposition the ruler as required. You can use the databar and context menu information you can use the measure function to measure distances in the chart application. You can determine the distance and bearing: • from your vessel to the position of the cursor; • between two points on the chart. Measuring from vessel position to cursor From the chart application: 1.
Chapter 17: Fishfinder application Chapter contents • 17.1 How the fishfinder works on page 178 • 17.2 Fishfinder introduction on page 179 • 17.3 Multiple sonar module support on page 180 • 17.4 Transducer bandwidth on page 180 • 17.5 The sonar image on page 181 • 17.6 Fishfinder presets on page 182 • 17.7 Dual / Single frequency fishfinder on page 182 • 17.8 Non-CHIRP (traditional) sonar module frequency controls on page 183 • 17.9 CHIRP sonar module frequency controls on page 184 • 17.
17.1 How the fishfinder works The fishfinder application uses a sonar module and a suitable sonar transducer. The sonar module interprets signals from the transducer and builds up a detailed underwater view. The transducer is located on the bottom of the boat, it sends pulses of sound waves into the water and measures the time it takes for the sound wave to travel to the bottom and back.
17.2 Fishfinder introduction Warning: Sonar operation Fishfinder context menu The fishfinder application includes a context menu which provides fishfinder information and shortcuts to menu items. • NEVER operate the sonar with the vessel out of the water. • NEVER touch the transducer face when the sonar is powered on. • SWITCH OFF the sonar if divers are likely to be within 7.6 m (25 ft) of the transducer.
17.3 Multiple sonar module support 17.4 Transducer bandwidth Your multifunction display supports the use of multiple sonar modules on the same network. The fishfinder application displays the fishfinder frequency, center frequency or CHIRP mode depending on the connected sonar module and transducer. You can select which sonar module you want to be displayed in the Fishfinder application. Only 1 sonar module can be displayed at any one time.
17.5 The sonar image Water depth Interpreting the bottom using sonar As water depth increases signal strength decreases, resulting in a lighter onscreen image of the bottom. It is important to understand how to correctly interpret the bottom structure represented on-screen. The bottom usually produces a strong echo. The following images show how different bottom conditions are represented on-screen: 1 Size of the target The larger the target, the larger the return on the fishfinder display.
17.6 Fishfinder presets 17.7 Dual / Single frequency fishfinder The fishfinder provides you with four preset configurations available from the fishfinder menu. These enable you to quickly select appropriate settings tailored for various situations. Dual frequency operation allows the sonar to operate and display 2 frequencies simultaneously. If the preset mode that you are using has two frequencies configured, you can view either one or both of those frequencies in separate windows.
17.8 Non-CHIRP (traditional) sonar module frequency controls 3. Operating frequency. The frequency of the sonar determines the width of the sonar beam, the depth to which the signals will penetrate and the resolution of the image. The frequencies supported depend upon the sonar module and transducer in use on your system. • Auto. When operating in automatic the system will set and the frequency automatically to suit your transducer operating conditions. • Lower frequencies (e.g.
17.9 CHIRP sonar module frequency controls The frequency of the sonar determines the width of the sonar beam, the depth to which the signals will penetrate and the resolution of the image The frequencies supported depend upon the sonar module and transducer in use on your system: • Lower frequencies produce a wider sonar beam and penetrate the water well. A lower frequency provides a lower resolution image that may not be as good at detecting small fish.
17.10 Fishfinder display modes Selecting a fishfinder display mode From the fishfinder application: 1. Select Menu. 2. Select Display Mode. 3. With dual frequency preset set, select Adjust to select which frequency display you wish to change. Selecting Adjust in Dual frequency preset will switch between Frequency 1 and Frequency 2. 4. Select the Select Mode menu item. 5.
7. Select Back or use the Ok button to confirm the setting. Adjusting the position of the fishfinder zoomed area When the zoom function is selected, the system automatically selects the zoom position so that the bottom details are always in the lower half of the display. If required you can reposition the portion of the image to be zoomed so that an alternative area is displayed. From the fishfinder application, with Zoom preset selected: 1. Select Menu. 2. Select Display Mode. 3. Select Zoom Position.
17.11 Fishfinder range Rotary Control • New c Series • New e Series The Range and Range Shift functions enable you to change the range of depth displayed by the fishfinder. • RMK-9 keypad Range The Range function enables you to define the range of depth that you see in the fishfinder display. Range in and Range out buttons In Auto Range, the fishfinder application automatically adjusts the range to ensure the water column and bottom are always displayed.
17.12 Fishfinder sensitivity settings The Sensitivity settings menu provides access to features and functions which enhance what is displayed on screen. Sensitivity options include: • Gain • Gain Mode — Only available when connected to a non-CHIRP sonar module including the internal sonar module. • Color Gain • TVG • Color Threshold 3. Select Gain Mode. A list of available auto gain modes is displayed: • Cruising (Low) • Trolling (Med) • Fishing (High) 4. Select the required auto gain mode.
Fishfinder color gain You can adjust the color gain to change the signal strength threshold for the strongest color in your fishfinder display. Color gain sets the lower limit for the strongest echo color. All echoes with a signal strength above this value are displayed in the strongest color. Those with a weaker value are divided equally between the remaining colors. • Setting a low value produces wide band for the weakest color, but a small signal band for the other colors.
When in manual mode the slider bar control is shown: Note: New c Series TVG controls are accessed by the menu options: Menu > Sensitivity Settings > TVG. 4. Adjust the color threshold to the required setting. 5. Select Ok to confirm setting and close the numeric adjust control. Fishfinder power The power setting controls the power level of the transducer. Enabling and disabling on-screen gain controls You can enable and disable the on-screen gain controls by following the steps below.
17.13 Fishfinder presentation options The Presentation menu gives you access to features and functions which provide additional on-screen functionality. Menu Item Description Options Gain controls Controls whether or not the on-screen Gain and TVG controls are shown or not • Show (default) Presentation options include: Menu Item Description Options Target Depth ID Controls whether the depth of identified targets are displayed.
17.14 Depth and distance with the fishfinder Fishfinder marker context menu The fishfinder marker includes a context menu which provides marker information and menu items. The fishfinder display provides a number of features to help you determine depths and distances.
17.15 Fishfinder scrolling 17.16 Fishfinder waypoints The fishfinder image scrolls from right to left. You can pause the scrolling or adjust the scroll speed, to ease placing of waypoints or VRMs on-screen. Placing a waypoint on the fishfinder display enables you to mark a position so that you can return to it later. Scroll speed When a waypoint is placed, its details are added to the waypoint list and a vertical line labelled WPT is displayed on-screen.
17.17 Fishfinder alarms The display can be configured to provide a number of fishfinder alarms. The following fishfinder alarms can be set when a sonar module is detected, or when the simulator is on: • Fish — alarm sounds when a target meets the specified sensitivity level and, is within the depth limits (if enabled). • Fishfinder Deep — alarm sounds when the sonar module detects that the depth is greater than the deep limit.
17.18 Sounder set-up menu options This section describes the settings you can change using the sounder set up menu: (Menu > Set-up > Sounder Set-up). The set up menu contains settings that are likely to be changed infrequently. Menu Item Description Options Sounder Switch between available sonar modules. List of available sonar modules. Note: Sounder selection is only available when more than 1 sonar module is available on the network.
17.19 Transducer set-up menu options The Transducer Set-up menu should be used when setting up your multifunction display for the first time or when installing a depth transducer. Menu Item Description Options Transducer Select the appropriate transducer type from those displayed. Some transducers may be detected by the system automatically. Options available are dependent on the sonar module connected. Speed Transducer Select the appropriate speed transducer from those available.
17.20 Resetting the sonar The reset function restores the unit to its factory default values. Note: Performing a factory reset will clear speed and temperature calibration settings and the depth offset. 1. Using a compatible Raymarine multifunction display go to the Fishfinder application page. 2. Select Menu from the side menu. 3. Select Set-up. 4. Select Sounder Set-up. 5. Select Sonar reset. 6. Select Yes to confirm. The unit will now be reset to factory default settings.
a Series / c Series / e Series
Chapter 18: Fishfinder application with DownVisionTM Chapter contents • 18.1 Fishfinder introduction on page 200 • 18.2 The sonar image on page 203 • 18.3 Fishfinder display modes on page 203 • 18.4 Fishfinder range on page 205 • 18.5 Fishfinder sensitivity settings on page 206 • 18.6 Fishfinder presentation options on page 208 • 18.7 Depth and distance with the fishfinder on page 209 • 18.8 Fishfinder scrolling on page 210 • 18.9 Fishfinder waypoints on page 210 • 18.
18.1 Fishfinder introduction Sonar overview Various sonar technologies are available, all of which work on the same basic principles. The sonar transducer sends pulses of sound waves into the water and measures the time it takes for the sound wave to travel to the bottom and back. The returning echoes are affected by bottom structure and by any other objects in their path, for example reefs, wrecks, shoals or fish.
Dragonfly (internal sonar) DownVisionTM — CHIRP • target images indicating fish. a68 / a78 (internal sonar) DownVisionTM — CHIRP • a status bar displaying setting information. CP300 traditional sonar • bottom depth.
Fishfinder context menu The fishfinder application includes a context menu which provides fishfinder information and shortcuts to menu items. 3. Select the View you want to use. Selecting a view when changing settings In splitscreen views you can choose which view you want setting changes to be applied to or changes can be applied to both views at the same time. Form the Fishfinder application with a splitscreen view displayed. 1. Select the relevant item from the menu.
18.2 The sonar image 18.3 Fishfinder display modes Factors influencing the sonar display Selecting a fishfinder display mode The quality and accuracy of the display can be influenced by a number of factors including vessel speed, depth, object size, background noise and transducer frequency. From the fishfinder application: 1. Select Menu. 2. Select Display Mode. 3. With a splitscreen view displayed, select Adjust 4. Select Sonar, DownVision or Both. 5. Select the Select Mode menu item. 6.
Adjusting the position of the fishfinder zoomed area Bottom Lock When the zoom function is selected, the system automatically selects the zoom position so that the bottom details are always in the lower half of the display. If required you can reposition the portion of the image to be zoomed so that an alternative area is displayed. The Bottom Lock function applies a filter to flatten the image of the seabed and make any objects on or just above it easier to see.
18.4 Fishfinder range Using range shift The Range and Range Shift functions enable you to change the range of depth displayed by the fishfinder. The default setting adjusts the display to keep the bottom in the lower half of the display window. Alternatively you can shift the image within the current range. Changes to the range shift are reflected in all windows. Range The Range function enables you to define the range of depth that you see in the fishfinder display.
18.5 Fishfinder sensitivity settings The Sensitivity settings menu provides access to features and functions which enhance what is displayed on screen. Fishfinder gain onscreen controls Touchscreen multifunction displays provide onscreen access to the gain controls. Sensitivity options include: • Gain • Color Gain • Noise Filter • Color Threshold Sensitivity settings for Sonar and DownVisionTM can be changed independently or both at the same time.
• Manual — You can set the color gain manually, between a value of 0% to 100%. Selecting the view for color gain adjustments To select a view to apply color gain adjustments to follow the steps below. From the fishfinder application: 1. Select Menu. 2. Select Sensitivity Settings. 3. Select Color Gain. 4. Select Adjust. 5. Select Sonar, DownVision or Both. 1. Select Menu. 2. Select Sensitivity Settings. 3. Select Color Threshold. Selecting color threshold displays the numeric adjust control. 4.
18.6 Fishfinder presentation options The Presentation menu gives you access to features and functions which provide additional on-screen functionality. Menu Item Description Options Gain controls Controls whether or not the onscreen Gain and Noise Filter controls are displayed.
18.7 Depth and distance with the fishfinder Fishfinder marker context menu The fishfinder marker includes a context menu which provides marker information and menu items. The fishfinder display provides a number of features to help you determine depths and distances.
18.8 Fishfinder scrolling 18.9 Fishfinder waypoints The fishfinder image scrolls from right to left. You can pause the scrolling or adjust the scroll speed, to ease placing of waypoints or VRMs onscreen. Placing a waypoint on the fishfinder display enables you to mark a position so that you can return to it later. Scroll speed When a waypoint is placed, its details are added to the waypoint list and a vertical line labelled WPT is displayed on-screen.
18.10 Sounder set-up menu options This section describes the settings you can change using the sounder set up menu: (Menu > Set-up > Sounder Set-up). The set up menu contains settings that are likely to be changed infrequently. Menu Item Description Options Sounder Switch between available sonar modules. List of available sonar modules. Note: Sounder selection is only available when more than 1 sonar module is available on the network.
18.11 Transducer set-up menu options The Transducer Set-up menu should be used when setting up your multifunction display for the first time or when installing a depth transducer. Menu Item Description Options Transducer Select the appropriate transducer type from those displayed. Some transducers may be detected by the system automatically. Options available are dependent on the sonar module connected. Speed Transducer Select the appropriate speed transducer from those available.
18.12 Fishfinder alarms 18.13 Resetting the sonar The display can be configured to provide a number of fishfinder alarms. The reset function restores the unit to its factory default values. The following fishfinder alarms can be set when a sonar module is detected, or when the simulator is on: • Fish — alarm sounds when a target meets the specified sensitivity level and, is within the depth limits (if enabled).
a Series / c Series / e Series
Chapter 19: Radar application Chapter contents • 19.1 Radar overview on page 216 • 19.2 Radar scanner status symbols on page 217 • 19.3 Radar display overview on page 218 • 19.4 Radar range and image quality on page 219 • 19.5 Target tracking on page 221 • 19.6 Distances, range, and bearing on page 223 • 19.7 Radar mode and orientation on page 225 • 19.8 Radar presentation menu options on page 227 • 19.9 • 19.10 HD and SuperHD radar adjustments on page 231 • 19.
19.1 Radar overview Radar is used to provide information that can help you to track targets and measure distances and bearings. Radio Detection And Ranging (RADAR) is used at sea to detect the presence of objects (known as ‘targets’) at a distance, and if they are moving, detect their speed. Radar works by transmitting radio pulses, then detecting reflections of these pulses (echoes) from objects in the area and displaying the reflections as targets on your display.
19.2 Radar scanner status symbols The radar scanner power mode status is indicated in the databar. Symbol Radar power mode 2. Select Power up Radar to turn the radar on, or Power down Radar to turn the radar off. 3. Select Radar: Tx to start the radar transmitting, or Radar: Stdby to stop the radar transmitting. Description Transmit (TX) Rotating icon, signifying that the scanner is on and transmitting. When SCANNER is set to ON, select this mode to activate the scanner.
19.3 Radar display overview With your radar scanner connected and the radar in transmit mode, the radar picture provides a map-like representation of the area in which the radar is operating. better clarity. Be aware that the size of a target on screen is dependent on many factors and may not necessarily be proportional to its physical size. Nearby objects may appear to be the same size as distant larger objects. Note: Colors stated above refer to the default color palette.
19.4 Radar range and image quality 1 Maximum radar range The usable range of the radar is limited by factors such as the height of the scanner, and height of the target. 2 2 Maximum radar range is essentially line-of-sight, so is limited by the height of the scanner and the height of the target as illustrated below: 6 4 5 3 R ma x 6 a1 D1638-5 a2 2 h H 1 3 R ma x = 2.
Blind Sectors Obstructions such as funnels and masts near the radar antenna may obstruct the radar beam and cause radar shadows or ‘blind sectors’. If the obstruction is relatively narrow, there will be a reduction of the beam intensity, though not necessarily a complete cut-off. However, for wider obstructions there may be a total loss of signal in the shadow area. There may also be multiple echoes which extend behind the obstruction.
19.5 Target tracking Adjusting guard zone sensitivity The Guard Zone , VRM/EBL and MARPA functions will help you track targets and avoid collisions. You can adjust the threshold at which the alarm is triggered by a target entering the guard zone. With a radar connected to your multifunction display, you can: From the Radar application menu: 1. Select Zones. 2. Select Sensitivity. The sensitivity numeric adjust control is displayed. 3. Adjust the sensitivity to the required value. 4.
There are conditions where acquiring a target may become difficult. These same conditions may be a factor in successfully tracking a target. Some of the conditions are: • The target echo is weak. The target is very close to land, buoys or other large targets. • The target or your own vessel is making rapid manoeuvres. • Choppy sea state conditions exist and the target is buried in excessive sea clutter or in deep swells.
19.6 Distances, range, and bearing Vessel vectors (CPA graphics) overview CPA graphics show vectors for your vessel and a selected target. A vector is a line on-screen showing the predicted courses of your vessel and the selected target if you both remain on your present course. These vectors vary in length due to vessel speed and vector length set in the MARPA Set-up menu. 2 1 When you are using the radar application, you can measure distances, ranges and bearings in a variety of ways.
Measuring using VRM/EBL VRM/EBL context menu Variable Range Markers (VRM) The VRM/EBL function includes a context menu which provides positional data and menu items. A Variable Range Marker (VRM) is a circle centred on your vessel’s position and fixed with respect to the heading mode. When this circle is adjusted to align with a target, its range from your vessel is measured and displayed on the Radar context menu when you select the VRM with the cursor.
19.7 Radar mode and orientation 2. Press the Ok button. The radar context menu is displayed. 3. Use the Rotary Control to select Float Center. 4. Press the Ok button. 5. Using the Joystick, move the center position of the circle to the desired position. 6. Press the Ok button to confirm the new position. Radar orientation modes The radar can operate in a number of orientation modes to suit different types of navigation.
Course-Up 1 The default motion mode is “Relative”, with center offset. N N 2 True Motion (TM) When the motion mode is set to True, fixed radar targets maintain a constant position and moving vessels (including your vessel) travel in true perspective to each other and to fixed landmasses on the screen. As the vessel’s position approaches the edge of the screen, the radar picture is automatically reset to reveal the area ahead. D12210-1 Item Description 1 Current course upwards.
19.8 Radar presentation menu options Function Description Options Dual Range This menu item allows you to turn Dual range mode On and Off. • On • Off Dual Range Channel This menu item allows you to choose long or short channel for dual range.
Function Description Options Color Palette This menu item allows you to select a Color Palette for the radar application. • Bold • Professional 1 • Professional 2 • Classic • Night Vision Range Rings This menu item allows you to turn the range rings On and Off. • On • Off Safe Zone Ring This item allows you to show or hid the safe zone ring in the radar application.
R ST IL LU RY 1 TE M PO 2 R A D R A AT IO N FT True motion mode example 3 4 D12745-1 1 Ships heading marker. 2 Target travelling at between 0 kt to 1 kt (Minimal to no wake). 3 Target moving in opposite direction to vessel (Wake appears in opposite direction to your vessel’s heading). 4 Target moving in same direction as vessel (Wake appears towards your vessel’s heading). Note: You may see a wake ‘ring’ around fixed targets due to small error factors such as rotation time delays.
19.9 Radar tuning: On-screen gain controls Touchscreen multifunction displays provide on-screen access to controls for Gain, Rain and Sea clutter. Gain control Rain control Sea control Note: non-touchscreen controls are accessed by the menu options: Menu > Rain and Menu > Adjust Gain. Enabling and disabling on-screen gain controls You can enable and disable the on-screen gain controls by following the steps below. On a touchscreen multifunction display, with the relevant application displayed. 1.
19.10 HD and SuperHD radar adjustments You can use the presets and other functions to improve the quality of the radar picture. The following settings are available from the Radar menu and apply to HD radomes, HD and SuperHD open array scanners: Menu Item Description Options Preset Mode The radar gain presets enable you to quickly select pre-configured settings to achieve the best picture in different situations. Raymarine strongly recommends the use of these presets to achieve optimum results.
Adjusting radar anti sea clutter From the Radar application menu, with the required Preset Mode selected: 1. Select Adjust Preset , where shall be the Preset mode already selected. 2. Select Sea: . 3. The Sea clutter slider bar control is displayed. 4. Adjust the Sea clutter slider bar control to the appropriate setting (between 0 and 100%), or 5. Select the Auto box so that a tick is placed in the box for automatic sea clutter control.
19.11 Non-HD digital radomes adjustments You can use the gain presets and other functions to improve the quality of the radar picture. The following settings apply to non-HD digital radomes and are available from the Radar menu: Menu Item Description Options Rain The radar scanner detects echoes from rain or snow. These echoes appear on screen as countless small echoes continuously changing size, intensity and position.
19.12 Dual range radar operation The Dual Range radar function enables you to view 2 ranges at the same time in separate windows. The function is available with SuperHD and HD radar scanners. Using your multifunction display and an HD or SuperHD radar scanner, you can view either a short or a long range image in separate radar windows.
19.13 Radar scan speed SuperHD open array radars with software version 3.23 or above or HD radomes support multiple scan speeds. Radar scan speed is set up using the Radar Set-up menu. When the system detects a scanner that is capable of operating at both 24 RPM and 48 RPM, 2 options are provided for scanner speed: • 24 RPM • Auto If you have a radar scanner that only operates at 24 RPM, the scanner speed option is disabled.
19.14 Radar Set-up menu The Radar Set-up menu enables you to configure the performance and behavior of your radar scanner.
19.15 Resetting the radar To reset radar settings to defaults follow the steps below: From in the radar application: 1. Select Menu. 2. Select Radar Set-up. 3. Select Advanced. 4. Select Reset Advanced. A confirmation pop up message is displayed. 5. Select Yes to confirm reset.
a Series / c Series / e Series
Chapter 20: Data application Chapter contents • 20.1 Data application overview on page 240 • 20.2 Selecting datapages using touch on page 241 • 20.3 Selecting datapages on page 241 • 20.4 Customizing the data application on page 242 • 20.5 Resetting minimum and maximum readings on page 251 • 20.
20.1 Data application overview 6. Apparent wind arrow (yellow) The Data application enables you to view data generated by the multifunction display or data that is available on your system. 7. Tide arrow (blue) Data can be obtained from devices connected using SeaTalkhs, SeaTalkng or NMEA protocols. Pre-configured datapages The default datapage configuration is dependant upon the boat type selected during the initial set-up wizard.
20.2 touch Selecting datapages using 20.3 You can scroll through all available pages using the touchscreen. Selecting datapages To select datapages using a non-touch multifunction display follow the steps below. From the data application: 1. Move the Joystick Down to goto the next page, or 2. Move the Joystick Up to goto the previous page. D12878-1 From the Data application: 1. Touch the screen. 2. Slide your finger up and let go of the screen to go to the next datapage. 3.
20.4 Customizing the data application You can customize the data application to show the system and instrument data that you require. In addition to displaying the default, pre-configured datapages in the data application, you can also: • Change the order datapages appear. • Customize datapages content to your specific requirements. • Rename the datapages. • Add new custom datapages. • Delete existing datapages. • Set boat details such as number of engines, fuel tanks, and batteries. 4.
Engine identification 5. Select OK on the Identify Engines confirmation dialog. Engine data can be shown on your multifunction display. The engines will now appear in the correct location on the engine data page. To enable engine data to be displayed you must connect your vessel’s engines CAN bus to your multifunction displays SeaTalkng bus. Depending on your engine and system type this may require the use of the Raymarine Engine & Control Interface (ECI).
Units set-up You can specify your preference for the units of measurement that will be used in all applications. Menu item Description Options Distance Units The units of measure that will be used in all applications for the display of all values related to distance. • Nautical Miles • NM & m (major units = Nautical Miles, minor units = meters) • Statute Miles • Kilometers Speed Units The units of measure that will be used in all applications for the display of all values related to speed.
List of data items Categories of data available to display in the data application, databoxes, databar, and expanded databar are shown below. Dial graphics are not available in databoxes or databars. The following table shows the data items available by category. Data Category Description Data Item Battery** Battery status Battery Amps Data application Graphics Battery Temperature Battery Voltage Boat Types of data generated by your vessel. For example, tank levels.
Data Category Description Data Item Engine** Types of data generated by engines. For example, oil pressure.
Data Category Description Data Item Fuel** Types of data related to the fuel system. For example, fuel levels. Fuel Level (%) Data application Graphics Total Fuel (vol) Fuel Flow Total Economy Estimated Fuel Remaining Distance to Empty Time to Empty Fuel Used (Trip) Fuel Used (Season) Environment Environmentalrelated data. For example, air temperature.
Data Category Description Data Item Data application Graphics Maximum Water Temperature GPS GPS-related data. For example, vessel position. Vessel Position COG & SOG COG SOG Maximum SOG Average SOG Heading Heading-related data. For example, locked heading. Heading Heading and Speed (Data application only.) Locked Heading Locked Heading Error LH Error and LH (Data application only.) Tack Heading Compass (Data application only.) Navigation Types of data related to navigation.
Data Category Description Data Item Data application Graphics Bearing to Waypoint BTW & DTW (Data application only.) Course Made Good CMG & DMG CMG & VMG (Data application only.) Distance to Waypoint Distance Made Good Waypoint ETA Waypoint TTG Route ETA Route TTG Pilot Pilot-related data. For example, rudder. Rudder Angle Speed Speed-related data. For example, VMG (Velocity Made Good) to Waypoint.
Data Category Description Data Item Time Time-related data. For example, local time. Local Time Data application Graphics Local Date Wind Wind-related data. For example, VMG (Velocity Made Good) to Windward.
Data Category Description Data Item Data application Graphics TWA & TWS TWA (CH) and TWS TWA and VMG GWD and Beaufort GWD & GWS None Note: *Dials and graphical representations are only available from the Data application. Databar and data cell overlays can only display digital items. Note: **The Battery, Engine, Fuel and Tanks menus will display 1 set of data items per configured device (e.g. if the system has been configured with 3 engines then 3 sets of engine data items will be displayed). 20.
a Series / c Series / e Series
Chapter 21: Thermal camera application — Pan and tilt cameras Chapter contents • 21.1 Thermal camera application overview on page 254 • 21.2 Thermal camera image on page 254 • 21.3 Controls overview on page 255 • 21.4 Camera control on page 256 • 21.5 Image adjustments on page 258 • 21.6 Pan and tilt camera — new camera interface on page 260 • 21.7 High power and high torque modes on page 263 • 21.
21.1 Thermal camera application overview The thermal camera application enables you to control a connected thermal camera and display its image on your multifunction display. 21.2 Thermal camera image The thermal camera provides a video image which is shown on your display. Thermal imaging (also known as infrared) cameras enable you to see clearly in low-light and no-light conditions.
Icon Description Rear-view mode — image is flipped horizontally. Zoom setting: 2x zoom. 21.3 Controls overview The thermal camera application is available on compatible Raymarine multifunction displays and systems. It includes controls for the thermal camera. Rotary control Zoom image in / out. Joystick • Pan and tilt camera Note: On touchscreen displays you can also use the touchscreen to pan and tilt the camera. Zoom setting: 4x zoom. Single active controller on network.
21.4 Camera control Panning and tilting, and the thermal image On a touchscreen multifunction display you can pan and tilt the thermal camera image using the touchscreen. Power up and standby When the breaker connecting power to the camera is switched on, the camera will run a boot up sequence lasting for about 1 minute, after which the camera will be in Standby mode. In order for the camera to operate, you must bring the camera out of standby mode using the camera controls.
Surveillance mode settings The scan width determines the distance that the camera pans left and right when in surveillance mode. 1. Select Menu. 2. Select Camera Set-up. 3. Select Stabilization Mode. Selecting Stabilization mode switches stabilization On and Off. Scan Speed Thermal camera point mode The scan speed determines the speed at which the camera pans left and right when in surveillance mode. Point mode is only applicable to thermal cameras which have mechanical stabilization.
21.5 Image adjustments Thermal camera reverse video Adjusting the thermal camera image You can reverse the polarity of the video image to change the appearance of objects on-screen. With the thermal camera application displayed: 1. Select Menu. 2. Select Adjust Contrast. 3. Select the Contrast, Brightness, or Color option as appropriate. The relevant numeric adjust control is displayed. 4. Adjust the value as required. 5. Select Back or Ok to confirm the new value.
3. Use the Image Type menu item to switch between IR and Visible Light views, as appropriate. Thermal camera rear view mode The rear view mode flips the video image horizontally, providing a “mirror image”. This is useful for example in instances where the camera is rear-facing and you are viewing the image on a forward-facing monitor. Enabling thermal camera rear view mode With the thermal camera application displayed: 1. Select Menu. 2. Select Image Options. 3. Select Rear View.
21.6 Pan and tilt camera — new camera interface The thermal camera application menu options for a pan and tilt thermal camera with the new camera interface are shown below. Activate Camera Brings the thermal camera out of standby mode. (only available when camera is in standby.) Pause Image • On • Off (default) Camera Home Select to return the camera to its home position. Image Options Select to display the Image Options sub-menu.
Camera Set-up menu Set Home Position Sets the camera’s current position as the Camera Home position. Slew Settings Provides automatic slew options and camera alignment settings. • Auto Slew to MOB • Auto Slew to dangerous AIS target • Auto Slew to dangerous MARPA target • Camera height above sea level Align Camera Enables changes to camera’s horizontal alignment. Elev Align Enables changes to camera’s elevation (vertical) alignment.
Note: The thermal camera menu options available are dependant on the software version of your multifunction display and thermal camera. If options are different than listed above please refer to the manual that accompanied your thermal camera and / or the installation and operations handbook which accompanied your multifunction display.
21.7 High power and high torque modes Camera State Camera setting Dual payload Single payload Standby • High Power Mode ON 22 W 17.4 W 8W 7.4 W 13 W 13 W 8W 7.4 W 30 W 19.4 W 20 W 16.
21.8 Pan and tilt camera — old camera interface The thermal camera application menu options for a pan and tilt thermal camera with the old camera interface are shown below. Activate Camera Brings the thermal camera out of standby mode. (only available when camera is in standby.) Pause Image • On • Off (default) Camera Home Select to return the camera to its home position. Image Options Select to display the Image Options sub-menu.
System Setup Settings to optimize operation for this particular system / installation. About / Help Helpful information and restore to factory defaults setting. Exit Cancels on-screen menu. Surveillance mode menu Menu item / Description Scan Width Video setup menu Settings / Operation This setting determines the distance that the camera pans left and right when in surveillance mode. Select from: • Narrow — The camera will scan approximately 20º left and right of the center (40º total).
Menu item / Description Settings / Operation Set Stow Position This option sets the current position as the Stow position. The camera moves to the stow position whenever it is turned off or put into Standby mode. Name Camera Use this option to name the camera. Surveillance mode This options enables you to set the scan width and speed when in surveillance mode. Exit Exit to main menu.
Chapter 22: Thermal camera application — fixed mount cameras Chapter contents • 22.1 Thermal camera application overview on page 268 • 22.2 Thermal camera image on page 268 • 22.3 Controls overview on page 269 • 22.4 Camera control on page 270 • 22.5 Image adjustments on page 270 • 22.
22.1 Thermal camera application overview The thermal camera application enables you to control a connected thermal camera and display its image on your multifunction display. 22.2 Thermal camera image The thermal camera provides a video image which is shown on your display. Thermal imaging (also known as infrared) cameras enable you to see clearly in low-light and no-light conditions.
Icon Description Zoom setting: 4x zoom. Single active controller on network. Multiple active controllers on network. PC / laptop detected on network. 22.3 Controls overview The thermal camera application is available on compatible Raymarine multifunction displays and systems. It includes controls for the thermal camera. Rotary control Zoom image in / out. OK Confirm menu selection. Joystick Navigate menus. CANCEL / Back Cancel selection. RANGE IN / OUT Zoom image in / out.
22.4 Camera control 22.5 Image adjustments Power up and standby Adjusting the thermal camera image When the breaker connecting power to the camera is switched on, the camera will run a boot up sequence lasting for about 1 minute, after which the camera will be in Standby mode. With the thermal camera application displayed: 1. Select Menu. 2. Select Adjust Contrast. 3. Select the Contrast, Brightness, or Color option as appropriate. The relevant numeric adjust control is displayed. 4.
Thermal camera reverse video You can reverse the polarity of the video image to change the appearance of objects on-screen. The reverse video option (video polarity) switches the thermal image from white-hot (or red-hot if the color mode setting is active) to black-hot. The difference between white-hot and black-hot is shown below: White-hot thermal image. Black-hot thermal image. You may find it useful to experiment with this option to find the best setting to suit your needs.
22.6 Fixed mount camera menu The thermal camera application menu options for a fixed mount thermal camera are shown below. Activate Camera Brings the thermal camera out of standby mode. (only available when camera is in standby.) Pause Image • On • Off (default) Image Options Select to display the Image Options sub-menu.
JCU Icon PC Icon Shows or hides the on-screen JCU connected icon. • On (default) Shows or hides the on-screen PC connected icon. • On (default) • Off • Off Restore Factory Defaults Enables you to restore the camera’s settings to factory default values. Note: The thermal camera menu options available are dependant on the software version of your multifunction display and thermal camera.
a Series / c Series / e Series
Chapter 23: Camera application Chapter contents • 23.1 Camera application overview on page 276 • 23.2 Camera cycling on page 277 • 23.3 Naming camera / video feeds on page 277 • 23.4 Adjusting the video image on page 278 • 23.5 Selecting the aspect ratio on page 278 • 23.6 Selecting a location to store recordings on page 279 • 23.7 Record and playback on page 279 • 23.
23.1 Camera application overview Changing the camera / video feed You can view a camera or a video feed which is connected directly to your multifunction display using the video input(s), or IP camera feeds which are available on your network. On a New a Series or New e Series display, if more than 1 feed is available you can change which feed is displayed on the screen using touch. The Camera application can be used to: • Display live camera feeds. • Automatically cycle through available camera feeds.
23.2 Camera cycling 23.3 Naming camera / video feeds When multiple camera / video feeds are available the camera application can be set up to automatically cycle through the available feeds at a specified time interval. With camera cycling turned on the camera application will cycle through the available video input(s) on the display and available networked IP camera feeds. The feeds will be cycled in the order they appear in the Camera selection menu: Menu > Camera.
23.4 Adjusting the video image 23.5 Selecting the aspect ratio If supported by your connected camera / video input device or networked IP camera, you can adjust the image settings. If supported by your connected camera / video input device or networked IP camera, you can manually change the aspect ratio between 4:3 and 16:9. With a video feed displayed in the Camera application: 1. Select Menu. 2. Select Adjust. 3. Select Contrast, Brightness, or Color, as appropriate.
23.6 Selecting a location to store recordings In order to record, playback or capture a still image of IP camera feeds you must select the location you want to save to. If saving to a memory card ensure that a memory card with sufficient space is inserted into the relevant card reader slot. Note: Do not save files to cartography chart memory cards. From the Camera application: 1. Select Menu. 2. Select Set-up. 3. Select Save Files to:. 4.
6. Select Play Video. The Video file is played. You can also playback video clips from the My Data menu from the Homescreen: Homescreen > My Data > Images and Videos. 23.8 Taking photos When a camera feed from an IP camera is displayed you can capture a still image. Photos can be taken using the following methods: Capture — Immediate image capture. Moving and copying video files You can copy and move files between your display’s internal storage and memory cards using the steps below.
6. Select Start Timer. The photo will be taken after the time delay specified has elapsed. A confirmation dialog is then displayed showing a preview of the photo taken. 7. Select OK to confirm. 8. Select View to view the photo fullscreen. 9. Select Delete to delete the photo. 6. Select Move or Copy. 7. Confirm the location you want to move or copy the file to. A progress indicator is displayed e.g.
a Series / c Series / e Series
Chapter 24: Fusion link application Chapter contents • 24.1 Fusion link overview on page 284 • 24.2 Media sources on page 285 • 24.3 Browsing music on page 287 • 24.4 Selecting shuffle and repeat functions on page 287 • 24.5 Adjusting volume levels for each zone on page 288 • 24.6 Selecting the zone to control on page 288 • 24.7 Adjusting the tone controls on page 289 • 24.8 Selecting the system to control on page 289 • 24.
24.1 Fusion link overview • Play / Pause the current track. The multifunction display can control a connected 700 series Fusion entertainment system. • Select the zone to be controlled. (For information on setting up zones refer to the manual that accompanied your Fusion entertainment system. • Set Shuffle and Repeat functions.
24.2 Media sources DVD The layout and controls available are determined by the selected media source. iPod 1 2 3 2 3 1 4 4 5 6 D12748-1 1 Album artwork. 2 Track title. 3 Artist. 4 Track progress. 5 Track number. 6 Album title. 5 D12750-1 1 Time elapsed. Menu options available for iPods are as follows: 2 Title. • Browse music. 3 Chapter. • Repeat. 4 Remote button. • Shuffle. 5 DVD remote controls including: • Tone Controls. • Directional keypad. • Select Fusion System.
Selecting a media source VHF You can select which media source you want to control. 1 2 3 D12753-1 1 Squelch control. 2 Channel. 3 Manual / Auto status. Menu options available for VHF radios are as follows: • Preset. From the Fusion link application: 1. Select Src:. A list of media sources is displayed. 2. Select the relevant media source. • Scan. • Tone Controls. • Select Fusion System. AUX 1 D12754-1 1 Input gain. Menu options available for AUX devices are as follows: • Tone Controls.
24.3 Browsing music You can browse the music available on your connected iPod or USB device. From the Fusion link application: 1. Select the Menu icon. 2. Select Browse Music. The media device name is displayed. 3. Select the media device. The contents of the device are displayed. 4. Browse the available folders by selecting on them. 5. Select the Back icon to move back up the folder structure. 6. Select the track that you want to listen to. The main screen is displayed and the track will begin to play.
24.5 Adjusting volume levels for each zone 24.6 Selecting the zone to control The volume level for each zone can be adjusted individually or you can adjust all zones at the same time. From the Fusion link application: 1. Select Zone:. The zone selection bar is displayed. From the Fusion link application: 1. Select Vol:. The zone volume control is displayed. 2. Select the relevant zone. 3. Adjust the volume level to the required setting. 4. Select the Back icon to go back to the main screen.
24.7 Adjusting the tone controls 24.8 Selecting the system to control The Bass, Middle, and Treble tone controls can be adjusted. Where more than one Fusion entertainment system is connected you can select which system the Fusion link application will control. From the Fusion link application: 1. Select the Menu icon. 2. Select Tone Controls. 3. Select either Bass, Middle, or Treble. 4. Adjust the level to the required setting. 5. Select Back to go back to the menu options. 6.
24.9 Menu options Menu option Media sources Description Browse Music • iPod. • USB. Enables browsing of music stored on the device. • iPod. • Off • USB. • Folder — Repeats all songs in the current folder. • iPod. Switches track shuffle on and off. Repeat Shuffle • USB. Tone Controls • All devices. Enables adjustment of the following tone controls: • Bass. • Middle. • Treble. Select Fusion system • All devices. Enables you to select the Fusion entertainment system you want to control.
Chapter 25: Weather application (North America only) Chapter contents • 25.1 Weather application overview on page 292 • 25.2 Weather application set up on page 292 • 25.3 Weather application display overview on page 293 • 25.4 Weather map navigation on page 296 • 25.5 Weather context menu on page 296 • 25.6 Weather information on page 297 • 25.7 Weather reports on page 297 • 25.8 Animated weather graphics on page 298 • 25.9 Weather application menu options on page 299 • 25.
25.1 Weather application overview 25.2 Weather application set up The weather application overlays historical, live, and forecasted weather graphics on a world map. A number of steps must be completed before you can use the weather application for the first time. The weather application can only be used in North America and its coastal waters. • Your multifunction display must be connected to a Raymarine Sirius weather receiver.
25.3 Weather application display overview Symbol The weather application displays a range of graphics to indicate weather conditions and forecast information. 2 3 Lightning — a lightning symbol is shown at each cloud-to-ground strike: • Light (recorded in last 10–15 minutes.) The following diagram illustrates the main features of the weather application display: 1 Description • Medium (recorded in last 5–10 minutes.) 4 • Dark (recorded in last 0–5 minutes.
Historical (grey) Current (red) Forecast (orange) Wind speed symbols Description Hurricane (Category 1–5) The weather application uses a range of symbols to represent different wind speeds.
NOWRad precipitation color codes Reflectivity Intensity Rainfall (mm/hr) Rainfall (in/hr) NOWRad displays the type and level of precipitation: 85 7487.83 292.03 Color code Precipitation type Reflectivity Intensity 90 15376.51 599.69 Light green Rain (15 to 19 dBz) 95 31575.91 1231.46 Medium green Rain (20 to 29 dBz) 100 64841.98 2528.84 Dark Green Rain (30 to 39 dBz) 105 133154.6 5193.03 Yellow Rain (40 to 44 dBz) 110 273436.4 10664.
25.4 Weather map navigation 25.5 Weather context menu You can move around the weather map and place waypoints. The weather application includes a context menu which provides positional data and the option to view weather reports from the cursor location. When you open the weather application, a world map is displayed. If the system has a position fix for your vessel, the map will be centred on your location.
25.6 Weather information 25.7 Weather reports You can view weather information for: You can view a number of different weather reports to give you a comprehensive view of the weather. • a specific location • a surface observation station (when displayed) • Cities (when displayed) Your multifunction display shows weather reports for: • Tropical statements. • Marine warnings. Viewing weather data at a specific location • Marine zone forecasts.
25.8 Animated weather graphics You can view animated weather graphics to provide an indication of changing weather patterns. The animated weather option enables you to view an animation from the current time for: • NOWRad — weather radar 1 • Wind • Waves • Pressure — surface pressure D12297-1 Item Description 1 Watchbox alert box Viewing watchbox alerts You can view a watchbox alert at any time by following the steps below: From the weather application with a watchbox alert box displayed. 1.
25.9 Weather application menu options The following options are available from the weather application menu: Menu item Description Find Ship Selecting Find Ship will reset the display to show your vessel in the center of the screen. Display Graphics The Display Graphics menu allows to choose what graphics to Show or Hide in the weather application. Menu item Description Options Watchbox Alert The Watchbox Alerts menu allows you to turn alerts Off, or select a range.
25.10 Glossary of weather terms Term Definition Cold front The boundary between two different air masses where cold air pushes warm air out of the way and brings colder weather. Cyclone A large area of low atmospheric pressure, characterized by inward spiralling winds. A “low” also called a “depression”. Also the name used for a hurricane in the Indian Ocean and Western Pacific. Depression An area of low pressure. Also called a cyclone.
Term Definition Typhoon The name for a tropical storm originating in the Pacific Ocean, usually the China Sea. They are basically the same as the hurricanes of the Atlantic Ocean and the cyclones of the Bay of Bengal. Wave cyclone A storm or low pressure centre that moves along a front. Wave period The period is the time gap between successive waves and the longer the period the faster the waves travel.
a Series / c Series / e Series
Chapter 26: Sirius audio application (North America only) Chapter contents • 26.
26.1 Sirius audio overview A connected, compatible Raymarine Sirius marine weather / satellite radio receiver can be controlled using the Sirius audio application. Note: A Sirius subscription is required to enable use of a Sirius marine weather / satellite radio receiver. To enable volume controls the Raymarine Sirius marine weather / satellite radio receiver also needs to be connected to a vessel entertainment system.
Chapter 27: Mobile applications Chapter contents • 27.1 Raymarine mobile apps on page 306 • 27.2 Enabling Wi-Fi on page 307 • 27.3 Enabling mobile apps on page 307 • 27.4 Setting up Wi-Fi security on page 308 • 27.
27.1 Raymarine mobile apps 1 2 3 4 Raymarine mobile apps enable viewing and control of your multifunction display via a compatible mobile device, using a Wi-Fi connection. Raymarine currently offers the following mobile apps: • RayView D125 99- 2 • RayRemote 1. Multifunction display. • RayControl 2. Wi-Fi connection (2 way – streaming or remote control). Note: Your multifunction display must have software version V3.15 or later in order to use mobile apps. 3. Compatible smartphone. 4.
27.2 Enabling Wi-Fi 27.3 Enabling mobile apps With the homescreen displayed: 1. Select Set-up. 2. Select System Settings. 3. Select Wireless Connections. 4. Select Wi-Fi > ON. Raymarine mobile apps must be enabled on your multifunction display before you can stream video or remote control your multifunction display via a tablet or smartphone device. Mobile applications With the homescreen displayed: 1. Select Set-up. 2. Select System Settings. 3. Select Wireless Connections. 4. Select Mobile apps. 5.
27.4 Setting up Wi-Fi security 27.5 Selecting a Wi-Fi channel You can encrypt the Wi-Fi connection on the multifunction display to prevent unauthorized devices from accessing the connection. The default encryption is WPA2. By default the multifunction display automatically selects an available Wi-Fi channel.
Chapter 28: Customizing your display Chapter contents • 28.1 Language selection on page 310 • 28.2 Boat details on page 311 • 28.3 Units set-up on page 312 • 28.4 Time and Date set-up on page 313 • 28.5 Display preferences on page 314 • 28.6 Databar and databox overview on page 316 • 28.7 List of data items on page 317 • 28.
28.1 Language selection The system can operate in the following languages: English (US) English (UK) Arabic Bulgarian Chinese Croatian Danish Dutch Finnish French German Greek Icelandic Italian Japanese Korean Norwegian Polish Portuguese (Brazilian) Russian Spanish Swedish Turkish With the homescreen displayed: 1. Select Customize. 2. Select Language. 3. Select from the languages available.
28.2 Boat details You can customize various settings to make them specific to your vessel. Menu item Description Options Boat Type You can change the appearance of the vessel in the chart application. Select the option that most closely resembles the type and size of your vessel. • Power Cruiser 1 (default) Note: When boat type is selected during the initial set up of the multifunction display the boat type shall determine the datapage configuration in the data application.
28.3 Units set-up You can specify your preference for the units of measurement that will be used in all applications. Menu item Description Options Distance Units The units of measure that will be used in all applications for the display of all values related to distance. • Nautical Miles • NM & m (major units = Nautical Miles, minor units = meters) • Statute Miles • Kilometers Speed Units The units of measure that will be used in all applications for the display of all values related to speed.
28.4 Time and Date set-up You can specify your preference for the way that time and date will appear in all applications. Menu item Description Options Date Format Allows you to specify the preferred format for the display of date information in all applications. • MM:DD:YY (Month, Day, Year) Allows you to specify the preferred format for the display of time information in all applications.
28.5 Display preferences You can specify your preference for general display behavior. Menu item Description Options Starting page Allows you to select what page the display opens at start up. • Homescreen (default) • Last page — After power up the last used page is displayed. • Choose page — After power up the page selected is displayed. Key Beep Cursor Autohide Range Controls An audible sound can be made each time a button is pressed or the touchscreen is used.
Shared brightness You can set up shared brightness groups to adjust the brightness on multiple units simultaneously. The following units are compatible with shared brightness groups: • New a Series • New c Series. • New e Series. • gS Series • i50 • i60 • i70 • p70 / p70R pilot controllers • ST70 • ST70+ Once compatible units are added to a shared brightness group, any brightness adjustment made to any of the units in the group is also reflected in all other units in that group.
28.6 Databar and databox overview Customizing databoxes in the chart application You can customize the data displayed in the databar and onscreen databoxes. Customizable data is displayed in the databar, extended databar (HybridTouch displays only) or databoxes. The databar, extended databar and databoxes are available in all applications. These areas of the screen are illustrated and described below: 1 2 3 4 To switch databoxes on and off and to select data to display follow the steps below.
28.7 List of data items Categories of data available to display in the data application, databoxes, databar, and expanded databar are shown below. Dial graphics are not available in databoxes or databars. The following table shows the data items available by category. Data Category Description Data Item Battery** Battery status Battery Amps Data application Graphics Battery Temperature Battery Voltage Boat Types of data generated by your vessel. For example, tank levels.
Data Category Description Data Item Engine** Types of data generated by engines. For example, oil pressure.
Data Category Description Data Item Fuel** Types of data related to the fuel system. For example, fuel levels. Fuel Level (%) Data application Graphics Total Fuel (vol) Fuel Flow Total Economy Estimated Fuel Remaining Distance to Empty Time to Empty Fuel Used (Trip) Fuel Used (Season) Environment Environmentalrelated data. For example, air temperature.
Data Category Description Data Item Data application Graphics Maximum Water Temperature GPS GPS-related data. For example, vessel position. Vessel Position COG & SOG COG SOG Maximum SOG Average SOG Heading Heading-related data. For example, locked heading. Heading Heading and Speed (Data application only.) Locked Heading Locked Heading Error LH Error and LH (Data application only.) Tack Heading Compass (Data application only.) Navigation Types of data related to navigation.
Data Category Description Data Item Data application Graphics Bearing to Waypoint BTW & DTW (Data application only.) Course Made Good CMG & DMG CMG & VMG (Data application only.) Distance to Waypoint Distance Made Good Waypoint ETA Waypoint TTG Route ETA Route TTG Pilot Pilot-related data. For example, rudder. Rudder Angle Speed Speed-related data. For example, VMG (Velocity Made Good) to Waypoint.
Data Category Description Data Item Time Time-related data. For example, local time. Local Time Data application Graphics Local Date Wind Wind-related data. For example, VMG (Velocity Made Good) to Windward.
Data Category Description Data Item Data application Graphics TWA & TWS TWA (CH) and TWS TWA and VMG GWD and Beaufort GWD & GWS None Note: *Dials and graphical representations are only available from the Data application. Databar and data cell overlays can only display digital items. Note: **The Battery, Engine, Fuel and Tanks menus will display 1 set of data items per configured device (e.g. if the system has been configured with 3 engines then 3 sets of engine data items will be displayed).
28.8 System set-up menus The system set-up menus enable you to configure your display and connected external devices. The following menus are available: Menu item Description Notes Touch-Lock Enables you to lock the touchscreen of a touch only display when the display is paired with a remote keypad. • ON • OFF (default) Note: This option is not available on touch-only displays which do not have a remote keypad connected. Note: This option is not available on displays which have physical buttons.
Alarms menu Menu item Description Options MOB Data Type Determines whether Position or Dead Reckoning (DR) data is displayed. Assuming that your vessel and the MOB are subject to the same tide and wind effects, the Dead Reckoning setting normally gives a more accurate course. • Dead Reckoning When set to On, an alarm is triggered at the time you specify for the Alarm Clock Time setting. Alarm Clock Alarm Clock • Position (default) • Off (default) • On Alarm Clock Time • 00:00 (default) • 00.
Menu item Description Options • Deep Fish Limit — Specifies the upper value for the Fish Alarm Depth Limit. • 2 ft (or equivalent units) to the maximum of the transducer range Deep Fish Limit • 2 ft (or equivalent units) to the maximum of the transducer range Fuel Manager In the fuel manager alarm options you can switch the low fuel warning alarm on or off and specify the fuel level at which the alarm is triggered.
Ground trip resets menu This menu enables you to resets the chosen ground trip distance counter to zero. Menu item Description Ground Trip 1 Reset Resets the ground trip 1 distance counter to zero. Ground Trip 2 Reset Resets the ground trip 2 distance counter to zero. Ground Trip 3 Reset Resets the ground trip 3 distance counter to zero. Ground Trip 4 Reset Resets the ground trip 4 distance counter to zero. System settings menu • Satellite number.
Multiple data sources (MDS) overview Installations that include multiple instances of data sources can cause data conflicts. An example is an installation featuring more than one source of GPS data. MDS enables you to manage conflicts involving the following types of data: • GPS Position. • Heading. • Depth. • Speed. • Wind. Typically this exercise is completed as part of the initial installation, or when new equipment is added.
Data sources menu This menu enables you to select the external sensors and devices that will provide data to the display. Auto / manual selection Each dialog enables you to view and select your preferred data source. selection of data source can be manual or set to automatic: • Auto — the display will automatically select a device and attempt to resolve any data conflicts that may occur where there is more than one source of data for that particular data source (for example, multiple GPS receivers).
External devices menu This menu enables you to configure the external devices connected to the display. Menu item Description Notes Pilot Set-up When connected to an Evolution autopilot this option allows you to enable and disable pilot control and the pilot bar. You can also access certain pilot settings and modes. Fishfinder Set-up Enables you to select an external transducer and configure the options for the unit, such as depth offset.
Connections menu This menu enables you to connect wireless Bluetooth and Wi-Fi devices to the display. Menu item Description Options Bluetooth Enable or disable Bluetooth on the display. • On • Off (default) Wi-Fi Enable or disable Wi-Fi on the display. • On • Off (default) Connection Manager Provides a list of Bluetooth devices in range. When you highlight a connection in the list and press OK, the following options are available: • Unpair / Forget this device • Audio control On / Off.
NMEA Set-up menu This menu enables you to configure settings for NMEA devices. Menu item Description Options Bridge NMEA Heading If set to ON, NMEA heading data will be bridged onto the SeaTalk data bus, and will be sent to all NMEA-connected devices. If set to OFF, NMEA heading data will NOT be bridged onto the SeaTalk bus.
System preferences menu Menu item Description Options Bearing mode Determines how all bearing and heading data is displayed in. This does not affect how the chart or radar displays are drawn. • True (default) This setting compensates for the naturally occurring offset of the earth's magnetic field. When set to Auto, the system automatically compensates, and displays the compensation value in brackets.
Maintenance menu This menu provides access to systems settings reset and diagnostics. Menu item Description Touchscreen Alignment If the touchscreen is misaligned to your touch, you can realign it to improve the accuracy. Realignment involves a simple exercise to align an on-screen object with your touch. For best results, perform this exercise when your vessel is anchored or moored. Options Note: The Touchscreen alignment option is not required on New c Series displays.
Diagnostics menu If you encounter problems with your multifunction display or peripheral devices you can use the Diagnostics menu to view information about your device and connected equipment. Select Device Enables you to a list of all devices connected to the SeaTalkhs network. You can also select an item in the list to view further details for that device. • Device • Serial No.
a Series / c Series / e Series
Chapter 29: Maintaining your display Chapter contents • 29.1 Service and maintenance on page 338 • 29.
29.1 Service and maintenance 29.2 Cleaning This product contains no user serviceable components. Please refer all maintenance and repair to authorized Raymarine dealers. Unauthorized repair may affect your warranty. Best cleaning practices. Routine equipment checks Raymarine strongly recommends that you complete a number of routine checks to ensure the correct and reliable operation of your equipment.
Chapter 30: Troubleshooting Chapter contents • 30.1 Troubleshooting on page 340 • 30.2 Power up troubleshooting on page 341 • 30.3 Radar troubleshooting on page 342 • 30.4 GPS troubleshooting on page 343 • 30.5 Sonar troubleshooting on page 344 • 30.6 Thermal camera troubleshooting on page 345 • 30.7 System data troubleshooting on page 346 • 30.8 Video troubleshooting on page 347 • 30.9 Wi-Fi troubleshooting on page 348 • 30.10 Bluetooth troubleshooting on page 349 • 30.
30.1 Troubleshooting The troubleshooting information provides possible causes and corrective action required for common problems associated with marine electronics installations. All Raymarine products are, prior to packing and shipping, subjected to comprehensive test and quality assurance programs. However, if you experience problems with the operation of your product this section will help you to diagnose and correct problems in order to restore normal operation.
30.2 Power up troubleshooting Problems at power up and their possible causes and solutions are described here. Problem Possible causes Possible solutions The system (or part of it) does not start up. Power supply problem. Check relevant fuses and breakers. Check that the power supply cable is sound and that all connections are tight and free from corrosion. Check that the power source is of the correct voltage and sufficient current.
30.3 Radar troubleshooting Problems with the radar and their possible causes and solutions are described here. Problem Possible causes Possible solutions No Data or No scanner message Radar scanner power supply Check that the scanner power supply cable is sound and that all connections are tight and free from corrosion. Check relevant fuses and breakers. Check power source is of the correct voltage and sufficient current (using voltage booster if appropriate).
30.4 GPS troubleshooting Problems with the GPS and their possible causes and solutions are described here. Problem Possible causes Possible solutions “No Fix” GPS status icon is displayed. Geographic location or prevailing conditions preventing satellite fix. Check periodically to see if a fix is obtained in better conditions or another geographic location. GPS connection fault. Ensure that external GPS connections and cabling are correct and fault free. External GPS antenna in poor position.
30.5 Sonar troubleshooting Problems with the sonar and their possible causes and solutions are described here. Problem Possible causes Possible solutions Sonar data not available on multifunction display. Unit power supply fault. Check the unit power supply and cables. Other unit fault. Refer to the instructions supplied with the unit. SeaTalkhs / RayNet network problem. Check that the unit is correctly connected to a Raymarine network SeaTalkhs switch or crossover coupler (as applicable).
30.6 Thermal camera troubleshooting Problems with the thermal camera and their possible causes and solutions are described here. Problem Possible causes Possible solutions Video not displayed. Camera is in Standby mode. The camera will not display video if it is in Standby mode. Use the camera controls (either the thermal camera application or JCU) to “wake” the camera from standby. Problem with the thermal camera video connections.
30.7 System data troubleshooting Aspects of the installation can cause problems with the data shared between connected equipment. Such problems, their possible causes and solutions are described here. Problem Possible causes Possible solutions Instrument, engine or other system data is unavailable at all displays. Data is not being received at the display. Check the data bus (e.g. SeaTalkng) wiring and connections. Check the overall integrity of the data bus (e.g. SeaTalkng) wiring.
30.8 Video troubleshooting Problems with the video inputs and their possible causes and solutions are described here. Problem Possible causes Possible solutions No signal message on screen (video image not displayed) Cable or connection fault Check that the connections are sound and free from corrosion.
30.9 Wi-Fi troubleshooting Aspects of the installation can cause problems with the data shared between wireless devices. Such problems, their possible causes and solutions are described here. Problem Possible causes Possible solutions No wireless connection. Tablet / smartphone does not have a wireless connection established with the multifunction display. Ensure that Wi-Fi is enabled on the multifunction display (Homescreen: > Set-Up > System Settings > Wireless Connections > Wi-Fi > On).
30.10 Bluetooth troubleshooting Aspects of the installation can cause problems with the data shared between wireless devices. Such problems, their possible causes and solutions are described here. Problem Possible causes Possible solutions No wireless connection. iPhone does not have a Bluetooth connection established with the multifunction display. Ensure that Bluetooth is enabled on the multifunction display ( Homescreen: > Set-Up > System Settings > Connections > Bluetooth > On).
30.11 Touchscreen troubleshooting Problems with the touchscreen and their possible causes and solutions are described here. Problem Possible causes Possible solutions Touchscreen does not operate as expected. Touch lock is enabled. Use the Joystick to turn off the touch lock on the home screen. Screen is not being operated with bare fingers, for example gloves are being worn. Bare fingers must make contact with the screen for correct operation. Alternatively you may use conductive gloves.
30.12 Touchscreen alignment If the touchscreen is misaligned to your touch, you can realign it to improve the accuracy. Realignment involves a simple exercise to align an on-screen object with your touch. For best results, perform this exercise when your vessel is anchored or moored. Note: This only applies to touchscreen multifunction displays. Aligning the touchscreen With the homescreen displayed: 1. Select Set-up. 2. Select Maintenance. 3. Select Touchscreen Alignment. 4.
30.13 Miscellaneous troubleshooting Miscellaneous problems and their possible causes and solutions are described here. Problem Possible causes Possible solutions Display behaves erratically: Intermittent problem with power to the display. Check relevant fuses and breakers. • Frequent unexpected resets. • System crashes or other erratic behavior. Check that the power supply cable is sound and that all connections are tight and free from corrosion.
Chapter 31: Technical support Chapter contents • 31.1 Raymarine customer support on page 354 • 31.
31.1 Raymarine customer support 31.2 Third-party support Raymarine provides a comprehensive customer support service. You can contact customer support through the Raymarine website, telephone and e-mail. If you are unable to resolve a problem, please use any of these facilities to obtain additional help. Contact and support details for third-party suppliers can be found on the appropriate websites. Web support Navionics Please visit the customer support area of our website at: www.navionics.com www.
Chapter 32: Technical specification Chapter contents • 32.1 a Series on page 356 • 32.
32.1 a Series Fuse / Breakers It is recommended that you fit a thermal breaker or fuse at the distribution panel. The suitable fuse rating for the thermal breaker is dependent on the number of devices you are connecting. If in doubt consult an authorized Raymarine dealer Power consumption Full brightness: a6x Physical specifications Dimensions • Width: 163.57 mm (6.44 in) • Height (NOT including bracket): 143.47 mm (5.65 in) • Height (including bracket): 162.72 mm (6.41 in) • a75 / a75 Wi-Fi — 9.
a6x Display specification Operating frequency 1575.42MHz Size 5.7 in Signal Acquisition Automatic Type TFT backlit LED Almanac Update Automatic Color depth 24–bit Geodetic Datum Resolution 640 x 480 VGA WGS-84, alternatives available through Raymarine displays.
Conformance specification Conformance certification applies to all display variants Conformance • NMEA 2000 certification • WiFi Alliance certification 32.2 c and e Series e7 / e7D Physical specifications Dimensions • Width: 233 mm (9.17 in.) • Height (NOT including bracket): 145 mm (5.71 in.) • Bluetooth certification • Europe: 1999/5/EC • Height (including bracket): 180 mm (7.09 in.) • Australia and New Zealand: C-Tick, Compliance Level 2 • Depth (NOT including cables): 64 mm (2.52 in.
• 3.450 kg (7.6 lb.) Weight (boxed unit) Full brightness: Power consumption • c95 — 13.1 W e125 / c125 • c97 — 16.7 W • 4.955 kg (10.9 lb.) • e95 — 18 W e127 / c127 • e97 — 22.1 W • 5.070 kg (11.18 lb.) PowerSave mode: • c95 —5.9 W e165 Physical specifications Dimensions • c97 — 9.7 W • Width: 426 mm (16.8 in) • e95 — 11.2 W • Height (NOT including bracket): 281.4 mm (11.1 in) • e97 — 14.9 W • Height (including bracket): 295 mm (11.
Power consumption Full brightness: Color depth 24–bit • e165 — 59.5 W Resolution 800 x 480 pixels (WVGA) PowerSave mode: Maximum allowable wrongly illuminated pixels 8 • e165 — 10.9 W Note: Power consumption figures represent a loaded system and for sonar variants include an active 600 W transducer. LEN (Refer to Seatalkng reference manual for further information). 1 Environmental specification e125 / e127 / c125 / c127 Display specification Size 12 in.
Receiver IC Sensitivity 163 dBm Tracking Conformance specification Satellite Based Aiding System (SBAS) WAAS + EGNOS + MSAS Conformance certification applies to all display variants Special features Active Jamming Reduction • WiFi Alliance certification Operating frequency 1575.42MHz • Bluetooth certification Signal Acquisition Automatic • Europe: 1999/5/EC Almanac Update Automatic Geodetic Datum WGS-84, alternatives available through Raymarine displays.
a Series / c Series / e Series
Chapter 33: Spares and accessories Chapter contents • 33.1 Transducer accessories on page 364 • 33.2 DownVision transducers and accessories on page 364 • 33.3 Network hardware on page 365 • 33.4 Network cable connector types on page 365 • 33.5 Network cables on page 366 • 33.6 Network cable types on page 366 • 33.7 SeaTalkng cabling components on page 367 • 33.8 SeaTalkng cables and accessories on page 367 • 33.9 SeaTalk accessories on page 368 • 33.10 Video cables on page 369 • 33.
33.1 Transducer accessories Item Part number Notes P48 sonar transducer A102140 Transom mount. P58 sonar transducer A102138 Transom mount. 1 m (3.28 ft) Minn Kota transducer adaptor cable A62363 Only for direct connection to sonar variant multifunction display. 0.5 m (1.64 ft) transducer adaptor cable E66066 For connecting any 600 watt sonar module-compatible sonar transducer directly to a sonar variant multifunction display. 364 33.
33.3 Network hardware Item HS5 RayNet network switch Part number A80007 Notes 5–port switch for network connection of multiple devices featuring RayNet connectors. Equipment with RJ45 SeaTalkhs connectors can also be connected using suitable adapter cables. RJ45 SeaTalkhs network switch E55058 8–port switch for network connection of multiple SeaTalkhs devices featuring RJ45 connectors.
33.5 Network cables 33.6 Network cable types RayNet to RayNet cables There are 2 types of SeaTalkhs network cable — “patch” and “network”. Cable Part number 400 mm (1.3 ft) RayNet (F) to RayNet (F) cable A80161 2 m (6.56 ft) RayNet (F) to RayNet (F) cable A62361 5 m (16.4 ft) RayNet (F) to RayNet (F) cable A80005 10 m (32.8 ft) RayNet (F) to RayNet (F) cable A62362 20 m (65.6 ft) RayNet (F) to RayNet (F) cable A80006 100 mm (3.
33.7 SeaTalkng cabling components 33.8 SeaTalkng cables and accessories SeaTalkng cabling components and their purposes. SeaTalkng cables and accessories for use with compatible products. Connection / Cable Notes Backbone cable (various lengths) The main cable carrying data. Spurs from the backbone are used to connect SeaTalkng devices.
Description Part No Notes SeaTalkng Inline terminator A80001 Provides direct connection of a spur cable to the end of a backbone cable. No T-piece required. 33.9 SeaTalk accessories SeaTalk cables and accessories for use with compatible products. Description Part No 3–way SeaTalk junction box D244 1 m (3.28 ft) SeaTalk extension cable D284 3 m (9.8 ft) SeaTalk extension cable D285 SeaTalkng Blanking plug A06032 ACU / SPX SeaTalkng spur cable 0.3 m (1.
33.10 Video cables 33.11 a65 / a67 spares The following video cable is required for the video in / out connector on the e95 / e97 / e125 / e127 variant multifunction displays. Part number Description R70003 e-series accessory video cable Spares and accessories Notes Item Part number Trunnion (bracket) mount kit R70147 Front bezel R70148 Suncover R70149 Power cable 1.5m R70157 1.5 m (4.
33.12 e7 e7D spares Item Part number Trunnion (bracket) mount kit A62358 Documentation pack R62378 Flush mount panel set R62376 Front bezel R62377 Suncover R62365 1.5 m (4.9 ft) Straight power and data cable 1.5 m (4.9 ft) Right angled power and data cable 370 33.
33.14 e125 / e127 / c125 / c127 spares Item Part number c/e series trunnion kit Item Part number R70002 e165 trunnion kit A80176 c/e series front bezel R7006 e165 front bezel R70126 c/e series suncover R70007 e165 suncover R70127 c/e/ series rear bezel R70028 e165 flush mount kit R70125 c.e series gasket R70080 R62379 Mounting adaptor kit — C120W/E120W R70009 1.5 m (4.9 ft) Straight power and data cable R70029 Mounting adaptor kit — C120/E120 R70011 1.5 m (4.
a Series / c Series / e Series
Appendix A NMEA 0183 sentences The display supports the following NMEA 0183 sentences. These are applicable to NMEA 0183 and SeaTalk protocols.
Appendix B NMEA data bridging NMEA data bridging allows data that exists on the display’s NMEA 2000 bus to be repeated to NMEA 0183 devices, and vice versa. An example of NMEA data bridging is in a system that includes a third-party GPS receiver connected to the NMEA 0183 Input of a Raymarine display. The GPS data messages transmitted by the GPS receiver are repeated to any appropriate devices connected to the display's NMEA 2000 bus.
Appendix C NMEA 2000 sentences The display supports the following NMEA 2000 sentences. These are applicable to NMEA 2000, SeaTalkng and SeaTalk 2 protocols.
Transmit Message description 129794 AIS Class A Static and Voyage Related Data ● 129798 AIS SAR aircraft position report ● 129801 AIS Addressed Safety Related Message ● 129802 AIS Safety Related Broadcast Message ● 129808 DSC call information ● 129809 AIS class B “CS” static data report part A ● 129810 AIS class B “CS” static data report part B ● 130306 Wind data ● ● ● 130310 Environmental parameters ● ● ● 130311 Environmental parameters ● ● 130312 Temperature ● 13031
Appendix D Connectors and pinouts Pin Signal Power, data, and video connector 8 Not connected 9 Screen 10 Not connected 4 9 1 8 10 2 7 11 3 Note: Use only Raymarine RayNet cables when connecting SeaTalkhs devices. 6 5 D12186-1 SeaTalkng connector Item Remarks Identification PWR / NMEA / Video Connector type 11 pin twist-lock Current source to network No current sourced for external devices Current sink from network 5 6 4 • Video: No power required for interface.
PIN Signal 13 VIDEO IN2 RTN 14 RED RTN 15 RED Appendix E Switch panel application Vessel control and monitoring systems When integrated with a vessel control and monitoring system your multifunction display can provide monitoring and controls for your power circuits, breakers, switches and equipment. The Switch Panel application can be used to: • Show the status of power circuits, breakers, switches and other equipment. • Apply power to each circuit individually. • Reset tripped breakers.
3. Insert the memory card into the card reader on your multifunction display. 4. From the homescreen select Set-up. 5. Select System Settings. 6. Select External Devices. 7. Select Switch Panel Set-up. 8. Select Install Config File. 9. If prompted select the memory card slot that contains your configuration file. The file browser is opened. 10. Select the configuration file. 11. Select OK.
Appendix F Software releases Raymarine regularly updates its multifunction display software to introduce improvements, additional hardware support and user interface features. The table below details some of the important enhancements and which software revision they were introduced with. Software version Applicable product manual Multifunction displays compatibility LightHouse II — V9.
Software version Applicable product manual Multifunction displays compatibility V5.27 81337–5 a65 / a67 / c95 / c97 / c125 / c127 / e7 / e7D / e95 / e97 / e125 / e127 / e165 Changes • Addition of Fuel Manager including: Estimated fuel remaining, distance to empty and time to empty calculations, fuel used and fuel economy data, fuel range rings in the Chart application and low fuel alarm). • Addition of Document (pdf) Viewer application.
Software version Applicable product manual Multifunction displays compatibility Changes • Corrected the ability to select Tide and/or Current Station using the Find Nearest feature. • Added NMEA 0183 & SeaTalkng data monitors to the diagnostics features. • Increased touch area for Alarm pop-ups and Back buttons. V2.10 81337–1 c95 / c97 / c125 / c127 / e7 / e7D / e95 / e97 / e125 / e127 • Cartography redraw performance has been improved when sharing cartography via the SeaTalkhs/RayNet network.
www.ra ym a rin e .
