ELECTRIC PRESSURE WASHER INSTRUCTION MANUAL BYO1-VBJ-W BYO1-VBJ-WT WARNING: Do not use the appliance without reading the instruction manual.
3. PRODUCT OVERVIEW CONTENT Chapter 1.Application 2.Technical data 3. Product overview 4. Safety instructions 5. Operating instructions 6. After use instructions 7. Environmental protection 8. Maintenance, cleaning, repair 9. Trouble shooting 10. WEEE - Waste of electric and electronic equipment 11. Warranty 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. Page 1 1 1 2 4 7 7 7 9 10 10 1. APPLICATION Your electric pressure washer has been designed for outdoor cleaning.
• The operator and anyone in the immediate vicinity of the site of cleaning should take action to protect them from being struck by debris dislodged during operation. • Wear goggles and protection clothes during operation. • WARNING: This appliance has been designed for use with the cleaning agent supplied or recommended by the manufacturer. The use of other cleaning agents or chemicals may adversely affect the safety of the appliance.
for the safety of the appliance. Use only hoses, fittings and couplings recommended by the manufacturer. • WARNING: Inadequate extension cables can be dangerous. Cables on reels should always be completely unwinded to prevent the cable from overheating. • If an extension cable is used, the plug and the socket must be waterproof and comply with the below-mentioned requirements for length and cable dimensions. • 1.0mm² max. 12.5m • 1.5mm² max.
. OPERATION INSTRUCTIONS 5.1 Mounting of trolley handle 1. Place the trolley handle (6) on the machine (for BY01-VBJ-WT) 2. Secure the handle with the 4 screws. (for BY01-VBJ-WT) 5.4 Connection of garden hose 1. Screw the water inlet coupling (1) tight on to the water inlet Note: The inlet filter must always be fitted in the water inlet pipe to filter out sand, lime stone and other impurities as these will damage the pump valves. Caution: Failure to fit the filter will invalidate the guarantee. 2.
5.6 Mounting of lance and nozzle 5.8 Start/stop of the machine 1. Push the lance (13) into the trigger gun (11) 2. When inserted turn it. Caution: Make sure the lance (13) is properly fixed to the gun (11) 3. Attach the nozzles (14-19). Caution: When attaching the nozzle (14-19) the button (A) on the nozzle (14-19) should come out again. Check before activating the trigger that the nozzle (14-19) is properly fixed.
start again when you re- activate the trigger gun (11) 5.11 Angle Nozzle (optional) The angle nozzle (17) can be used for many applications e.g. cleaning the underbody of a car, underneath a lawn mover without being splashed back with debris, etc. 5.9 Adjustable Nozzle The pressure can be adjusted by turning the adjustable nozzle (14). WARNING: Do not do this under operation to avoid that the hand hits the jet.
C for storage of the hose (10) and cord (2) D B A Should the machine by mistake be frozen, it will be necessary to check it for damage. 6. AFTER USE INSTRUCTIONS The machine should be stored in a frost-free room! WARNING: Never start up a frozen machine. Frost damages are not covered by the guarantee! Pump, hose and accessories should always be emptied of water prior to storing as follows: 1.
working life, please take the following advice: • Wash out water hose, high pressure hose, spray lance and accessories before mounting. • Clean the connectors of dust and sand. • Rinse the detergent spraying attachment after use. • Clean the nozzles. Any repair should always be made in an authorized workshop with original spare parts 8.1 Cleaning of inlet filter Clean the water inlet filter regularly once a month or more frequently according to use.
9. TROUBLE SHOOTING Symptom Machine refuses to start Cause Recommended action Machine not plugged in Plug in machine. Defective socket Try another socket. Fuse has blown Replace fuse. Switch off other machines. Defective extension cable Try without the extension cable. Check that hoses and connections are airtight. Pump is sucking air Fluctuating pressure Valves dirty, worn out or stuck Contact your nearest service centre.
10. WEEE - WASTE OF ELECTRIC AND ELECTRONIC EQUIPMENT The symbol on the product or on its packing indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.
Zhejiang Xinchang Bigyao Power Tool Co., Ltd Head Office: Mengjiatang Industrial Zone, Xinchang County, Zhejiang Province, China USA Office: 101 wales avenue,Avon,MA 02322,United States Service Hotline: 888-899-1688 Email: realminfo@yahoo.
