User manual

1. All parts.
This is the carbons and other small
parts..
5. Assemble the main wing and the
fuselage and the head. Insert
the carbon lm, apply glue to the
corresponding area and stick together.
Tips: The carbon must be placed
across from main wing tip left to right.
After bonding, the plane should like
shown in following picture.
2. Cut the aileron and main wings with a
sharp cutter blade.
3. Cut the aileron, main wing, vertical tail
and at tail at 45° with a sharp cutter
blade.
Tips: You must cut very slowly. Don’t cut
over the under edge of the wing.
4. Cut a ne seam with a cutter blade
in the at tail. Apply glue to insert the
carbon.
Insert the carbon as shown in the picture.
6. Glue the tail.
Glue the tail as shown.
7. Attach the lower part of the fuselage.
Apply glue to the corresponding area
and glue.
After that, see the picture.
8. In the lower half of the fuselage,
the carbon rod slant supports are of
diameter in 1.0.
Tips: Cut the carbon very sharp, add
some glue on the tip, Go through the
board in the direction of the carbon.
Assemble the landing gear.
Assemble the main wing support small
board with a diameter of 1.0 carbon rod
and landing gear.
It is important to note that the main
wing connecting the fuselage should be
reinforced with a lot glue.
10. Cut the Aileron and elevator ctrl horn
seam. Tip: You can cut ne seam
following this picture. Glue the horn
from the elevator back and right side.
Glue the horn for rudder and aileron
later.
Installation and operating instructions
Unbreakable foam model aircraft (Extra 330SC)
Item no. 1590612
Intended use
This product is a model aircraft. It is suitable for outdoor use and designed for model aircraft beginners.
You can install compatible electrical drive and control components in the model. These are not included with
the product. A sample conguration of optional components is provided in the instructions. However, the
actual conguration may vary depending on the components used. Please refer to the technical data when
purchasing optional components.
Read the assembly and operating instructions carefully and store them in a safe place.
Make this product available to third parties only together with its operating instructions. This product complies
with statutory national and European regulations. All company and product names are trademarks of their
respective owners. All rights reserved.
Download the latest instructions at www.conrad.com/downloads or scan the QR code on
this page. Follow the instructions on the website.
Symbols
The symbol with the exclamation mark in the triangle is used to highlight important
information in these operating instructions. Always read this information carefully.
The arrow symbol indicates special information and advice on how to use the product.
Safety instructions
The product is not suitable for children under 14 years of age.
Read the instructions and safety information carefully. If you do not follow the safety
instructions and information on proper handling in this manual, we will assume no liability for
any resulting personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
You are solely responsible for the safe operation of this model!
• This product is not a toy. Keep it out of the reach of children and pets.
• Do not leave the packaging lying around carelessly, as it may become dangerous playing
material for children. Keep small parts out of the reach of children!
• When assembling the model, take care not to injure yourself on sharp edges or pointed ends.
• This model has the potential to cause damage to property and/or individuals. Make sure that
you are sufciently insured, e.g. by taking out private liability insurance. If you already have
such a policy, check with your insurance company that the use of this model is covered by the
policy. In some EU countries, you are required to have insurance when using a model aircraft.
• The product must not become damp or wet.
• Improper use can cause serious damage to people and property! Ensure that you maintain a
sufcient distance from peoples, animals and objects.
• Select a suitable location to y the model aircraft.
• Only y the model when you are fully alert and able to respond. Fatigue, alcohol and medication
can can affect your ability to respond.
• Do not direct the model towards spectators or towards yourself.
• Please refer to the manufacturer‘s safety and installation instructions when installing electrical
components.
If you have questions which remain unanswered by these instructions, contact our
technical support service or other technical personnel.
Disposal
Always dispose of the product according to the relevant statutory regulations.
You thus fulll your statutory obligations and contribute to the protection of the environment.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method (e.g. photocopy, microlming, or the capture in
electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.
This publication represents the technical status at the time of printing.
Copyright 2017 by Conrad Electronic SE. *1590612_v1_0817_02_DS_m_gb_(1)
9. Assemble the aileron and tail support.