Double Door Super Wide Safety Gate OWNER’S MANUAL MODEL: 1348, 1348DS • READ ALL INSTRUCTIONS BEFORE ASSEMBLY AND USE OF GATE. • KEEP INSTRUCTIONS FOR FUTURE USE. www.regalo-baby.com Regalo International, LLC. 3200 Corporate Center Drive, Suite 100 / Burnsville, MN 55306, USA 866.272.5274 (U.S. only) or 952.435.
Before Using Product Read and follow all instructions carefully to ensure that your gate and extensions are properly installed. Improper installation could result in the gate becoming unstable or dislodged from the doorway. Always make sure the extension is securely attached to the gate before using. The safety of your child is your responsibility. Please keep these instructions for your reference. IMPORTANT • The four mounting brackets must be used in securing the gate to the wall.
WARNING • To prevent serious injury or death, securely install gate or enclosure and use according to manufacturer’s instructions. • Children have died or been seriously injured when gates are not securely installed. ALWAYS install and use gate as directed using all required parts. • STOP using when a child can climb over or dislodge the gate. • Use only with the locking/latching mechanism securely engaged. • To prevent falls, NEVER use at top of stairs. • NEVER use to keep child away from pool.
Before Assembly A B D C E F G H PLEASE CHECK TO MAKE SURE YOU HAVE THE FOLLOWING PARTS: A Primary Door Panel (1) B Secondary Door Panel (1) C Gate Frame (6 Panels) D Plastic Mounting Brackets (4 – Attached to Gate Frame) E U-frame Support (1) F 1" Wall Mounting Screws (8) (requires a Phillips/cross-head screwdriver) G Frame Assembly Screws (4) H Hex Key English 5
Assembling Your Gate STEP 1 Connect the double doors by pushing the door frames together until the bases meet. STEP 2 Place the U-frame support on top of the connected door base an align screw holes. STEP 3 Use the hex key to fix the U-frame support to the door frame bases using the frame assembly screws.
Option A: Installing Your Gate Between Two Walls STEP 1 Unfold the gate frame by turning the locking knobs counter clockwise at each pivoting joint. Loosen the knobs enough to allow the gate to swing open freely without fully removing the knobs. LOCKING KNOB STEP 2 Arrange the gate panels to your desired configuration to fit your opening properly. STEP 3 Use a Phillips/cross-head screwdriver to fix the wall mounting bracket to the wall. Repeat for all four brackets.
STEP 4 Tighten all the locking knobs to secure your gate in place. NOTE: to maximum width openings 192 inches wide. 52.
Option B: Converting Your Gate to a Play Yard STEP 1 Unfold the gate frame by turning the locking knobs counter clockwise at each pivoting joint. Loosen the knobs enough to allow the gate to swing open freely without fully removing the knobs.
STEP 3 Position the play yard into your desired configuration (e.g. square), then join the free ends of the play yard together at the plastic joints. STEP 4 Insert one of the previously removed metal pivot bars through the opening created by joining the upper plastic joints. Guide the metal pivot bar downward into the circular housing on the lower plastic joint.
STEP 5 Reassemble the upper locking joint by adding one of the previously removed toothed disks and locking knobs. STEP 6 Tighten each of the locking knobs by turning them clockwise, fixing the play yard into the configuration you have chosen. To position the play yard into a new configuration or shape, simply loosen each of the locking knobs, adjust and re-tighten.
Operating the Single Door STEP 1 Simultaneously slide the lock and lift up the metal lift latch to unlock the door. The primary door will swing open in one direction only. METAL LIFT LATCH SLIDE LOCK STEP 2 To lock the gate, close the door completely and push the metal lift latch back into place.
Operating the Double Doors STEP 1 After you have opened the primary door, rotate the locking hinge on the secondary door. Lift the door up and swing open. The secondary door will open in either direction. LOCKING HINGE ROTATING LOCKING HINGE STEP 2 To close the secondary door, lift up on the door and place onto door frame base. Rotate the locking hinge to secure in place. SECURED LOCKING HINGE NOTE: Secondary door will only function when the primary door is open.
TO FOLD YOUR GATE STEP 1: Loosen all the locking knobs so the gate can move freely and become flexible at all the joints. STEP 2: Remove one of the locking knobs from the gate and remove one metal pivot bar. STEP 3: You will now be able to pull the two plastic joints at the top and bottom of the gate apart. STEP 4: Fold and put away. CARE AND MAINTENANCE Periodically check the gate for signs of damage, wear, or missing components. Do not use if any part is missing, worn or damaged.
Replacement Parts D C B A E N M K L F J G I O H A Door Frame Toothed Hinge White = #13009 I Bottom Hinge - Male White = #13002 B Top Hinge White = #13011 J Wall Mount Bottom Cap - Female White = #13014 C Locking Knob White = #13005 K 1” Wall Mount Screws #10001 D Toothed Hinge White = #13012 L 27” Metal Pivot Bar White = #13008 E Wall Mount Bracket White = #13007 M Wall Mount Toothed Disk White = #13013 F Wall Mount Bottom Cap - Male N Toothed Disk White = #13003 O Fram
www.regalo-baby.com Regalo International, LLC. 3200 Corporate Center Drive, Suite 100 Burnsville, MN 55306, USA 866.272.5274 (U.S. only) or 952.435.
