Installation manual

ManualsBrandsRegency ManualsLawn and GardenPT030-NG1

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

919-164b 06/09/14

Owners &

Installation Manual

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

Regency Plateau

PTO30 Outdoor

Decorative Gas Appliance

WARNING: FOR OUTDOOR USE ONLY

www.regency-ﬁ re.com

WARNING:

If the information in these instructions

are not followed exactly, a fire

or explosion may result causing

property damage, personal injury or

loss of life.

WARNING - FOR YOUR SAFETY

What to do if you smell gas:

•Shut off gas to the appliance.

•Do not try to light any appliance.

•Extinguish any open ﬂ ame.

•If odour continues, keep away from the appliance and im-

mediately call your gas supplier or ﬁ re department.

•Do not touch any electrical switch: do not use any phone

in your building.

•Immediately call your gas supplier from a neighbour's

phone.

•Follow the gas supplier's instructions.

•If you cannot reach your gas supplier, call the ﬁ re

department.

WARNING:

Improper installation, adjustment,

alteration, service or maintenance

can cause injury or property damage.

Read the installation, operating and

maintenance instructions thoroughly

before installing or servicing this

equipment.

Installation and service must be

performed by a authorised installer,

service agency or the gas supplier,

in accordance with this manual

WARNING:

Do not store or use gasoline or other ﬂ ammable vapours

and liquids in the vicinity of this or any other appliance.

Models: PTO30-NG1 / PTO30-LPG1

PTO30-ULPG1

LISTINGS AND CODE APPROVALS

These gas appliances have been tested

in accordance with AS4565 / AS4558

and have been certiﬁ ed by the IAMPO

Oceana for installation and operation

as described in these Installation and

Operating Instructions.

Your unit should be serviced annually

by an authorised service person.

Summary of content (32 pages)

PAGE 1
Regency Plateau® PTO30 Outdoor Decorative Gas Appliance Owners & Installation Manual Models: PTO30-NG1 / PTO30-LPG1 PTO30-ULPG1 LISTINGS AND CODE APPROVALS These gas appliances have been tested in accordance with AS4565 / AS4558 and have been certified by the IAMPO Oceana for installation and operation as described in these Installation and Operating Instructions. Your unit should be serviced annually by an authorised service person. WARNING: FOR OUTDOOR USE ONLY www.regency-fire.
PAGE 2
To the New Owner: Congratulations! You are the owner of a state-of-the-art Outdoor Decorative Gas Appliance by REGENCY®. The Plateau® PTO30 Outdoor decorative gas appliance has been designed to provide you with all the charm of a fire at the flick of a switch. The Plateau® PTO30 Outdoor Decorative Gas Appliance has been approved by IAPMO for both safety and efficiency. As it also bears our own mark, it promises to provide you with economy, comfort and security for many trouble free years to follow.
PAGE 3
TABLE OF CONTENTS PTO30 finished table top and Unit Dimensions .............5 Important Message ......................................................6 Before You Start ............................................................6 General Safety Information............................................6 Installation Checklist ......................................................7 Locating Your Outdoor decorative gas appliance ..........7 Minimum Clearances to combustibles ...........................
PAGE 4
SAFETY LABEL This is a copy of the label that accompanies each Plateau® Series Outdoor decorative gas appliance. We have printed a copy of the contents here for your review. NOTE: Regency® units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one. TO BE INSTALLED BY AN AUTHORISED PERSON Primarily a decorative appliance - not certified as a space heater.
PAGE 5
DIMENSIONS PTO30 FINISHED TABLE TOP AND UNIT DIMENSIONS 9-1/8" (231mm) 33-1/4" (844mm) 36-7/16" (932mm) SIDE VIEW Regency Plateau™ PTO30 Outdoor Gas Fireplace ADJUSTABLE 1/2" (13mm) to 2-3/8" (60mm) TOP VIEW 10-3/8" (263mm) 1-3/16" (30mm) OUTSIDE OF UNIT TO MOUNTING HOLES 10-9/16" (627mm) MOUNTING HOLES 37-9/16" (953mm) 8-1/4" (210mm) END VIEW 5
PAGE 6
INSTALLATION IMPORTANT MESSAGE SAVE THESE INSTRUCTIONS The PTO30 Outdoor Decorative Gas Appliance must be installed in accordance with these instructions. Carefully read all the instructions in this manual first. Consult the "authority having jurisdiction" to determine the need for a permit prior to starting the installation. It is the responsibility of the installer to ensure this decorative gas appliance is installed in compliance with manufacturers instructions and all applicable codes.
PAGE 7
INSTALLATION INSTALLATION CHECKLIST 1) Locate appliance: a) Refer to "Locating Your Outdoor decorative gas appliance" section b) Clearances to Combustibles (Refer to "Clearances" section) c) Framing & Finishing Requirements (Refer to "Framing & Finishing" section) 2) Drain Installation (recommended). 3) Install ON/OFF switch - ensure it is in the OFF position. 4) Make gas connections - test for leaks. 5) Install 4 "AA" batteries into each battery pack.
PAGE 8
INSTALLATION MINIMUM CLEARANCES TO COMBUSTIBLES The clearances listed below are Minimum distances unless otherwise stated: A major cause of fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this decorative gas appliance be installed only in accordance with these instructions. WARNING Fire hazard is an extreme risk if these clearances (air space) to combustible materials are not adhered to.
PAGE 9
INSTALLATION INNER FRAMING DIMENSIONS (REQUIRED) NOTE:FRAMING MATERIAL NOT SUPPLIED PTO30 37-15/16" (964mm) 8-3/4" (222mm) NOTE: Framing materials must be non-combustible when used within 4" of the unit. Combustible framing materials may be used outside the 4" clearance range. Finishing materials MUST be non-combustible. TOP VIEW Consideration should be given to weather / elements when choosing framing materials (ie. treated lumber, steel stud).
PAGE 10
INSTALLATION CONVERSION FROM NG TO LPG/ULPG THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !! Each Kit contains one LP Conversion Kit Conversion Kit # 377-968 Contains: Qty. Part # Description 1 904-655 Burner Orifice #45 1 904-529 5/32" Allen Key 1 918-590 Decal "Converted to LPG" 1 908-528 Red "LP / ULPG" label 1 911-009 Hi/Lo conversion LP / ULPG For 886 1 919-127 Instruction Sheet rn the unit off and allow to cool to room temperature. rn off gas supply.
PAGE 11
INSTALLATION 9) Remove 6 screws on valve access cover. 10) Remove Hi/Lo pressure regulator by removing 2 screws as shown below. Reverse steps to install LP pressure regulator. (Be sure diaphragm and spring are removed.) HI/LO pressure regulator 11) Attach the label “This unit has been converted to LPG/ULPG” near or on top of the serial # decal. 12) Replace yellow “NG” label with red “LPG/ULPG” label. Make appropriate gas connections.
PAGE 12
INSTALLATION FINISHING Side nailing strips are adjustable for material from a minimum of 1/2" thick up to a maximum of 2-3/8" thick. FINISHING MATERIALS: This burner is designed to be finished with non-combustible materials (ie. tile, granite, marble, brick, etc.) with a minimum thickness of 1/2" to a maximum thickness of 2-3/8". Min. 1/2" Max. 2-3/8" Nailing strip Burner Opening Size PTO30 36-7/16" x 8-1/4" PTO60 66-7/16" x 8-1/4" Side nailing strips are adjustable in 1/4" or 1/8" increments.
PAGE 13
INSTALLATION PTO30-NG SYSTEM DATA Max. Supply Pressure 14" WC (3.49 kpa) Min. Supply Pressure 5" WC (1.25 kpa) Manifold Pressure 3.5" WC (0.87 kpa) Manifold Pressure -Low 1.6" WC (0.40 kpa) Orifice Size #25 DMS Minimum Input 37 mj. Maximum Input 55 mj. 886 S.I.T. VALVE DESCRIPTION PILOT ADJUSTMENT Periodically check the pilot flames. Correct flame pattern has two strong blue flames: 1 flowing around the flame sensor and 1 flowing across the burner (it does not have to be touching the burner).
PAGE 14
INSTALLATION PTO30 WALL SWITCH INSTALLATION (INCLUDED WITH UNIT) The unit comes with low voltage wire and a battery extension wire installed. 1) Run supplied wire to desired location - to a max. of 9 feet. 6) Install supplied 4-AA batteries into the battery holder. Using velcro install battery holder to the backside of the battery compartment door. Connect battery terminal. 2) Install supplied electrical box in desired location.
PAGE 15
INSTALLATION PTO30 DRAIN INSTALLATION (RECOMMENDED) Although this decorative gas appliance is designed to operate outdoors safely, rain and other sources of moisture may enter the burner area, which will cause water to collect inside the base of the unit. NOTE: The PT060 requires installation of 4 drains (two per PT030).
PAGE 16
INSTALLATION PTO30 WIRING DIAGRAM This appliance does not require a 240V A.C. supply for operation. NOTE: 4 AA batteries must be installed in the battery pack to operate the burner switch. Do not use a 9 volt battery. Proflame System 0.886.001 Proflame Valve Standard Main On/Off Switch or Optional Wall Switch The appliance, when installed, must be electrically grounded in accordance with local codes, or in the absence of local codes with the National Electrical Code, ANSI/NFPA 70, if applicable.
PAGE 17
INSTALLATION TABLE COVER INSTALLATION DINING LEAF For all units: 1) Place the dining leaf cover over the burner of the unit when not in use.
PAGE 18
INSTALLATION GLASS CRYSTAL / BASALT VOLCANIC STONES INSTALLATION Evenly spread the Glass Crystals and optional Basalt Volcanic Stones over the burner. Ensure the crystals (or stones) do not overlap too much as this will effect the flame pattern. IMPORTANT NOTE: Only the supplied approved Glass Crystals and Basalt Volcanic stones are to be used with these fireplaces.
PAGE 19
INSTALLATION GLASS SURROUND INSTALLATION THE GUARD IS FITTED TO THIS APPLIANCE TO REDUCE THE RISK OF FIRE OR INJURY FROM BURNS AND NO PART OF IT SHOULD BE PERMANENTLY REMOVED. FOR PROTECTION OF YOUNG CHILDREN OR THE INFIRM , A SECONDARY GUARD IS REQUIRED. 4b. Use supplied spacer tool to determine where the bottom bracket should be placed and secured. 1. Remove metal fasteners from the corner brackets. 2.
PAGE 20
INSTALLATION ASSEMBLY INSTRUCTIONS FOR A STEEL STUD SEE THROUGH FRAMING KIT FOR PTO30 PTO30 BURNER MUST BE INSTALLED AT A MINIMUM OF 750MM ABOVE GROUND. IF INSTALLED LOWER, IT IS REQUIRED TO INSTALL THE DECORATIVE GLASS SURROUND AND ENSURE MINIMUM HEIGHT IS 750MM TO TOP OF GLASS SURROUND. IF INSTALLED LOWER THAN 750MM WITH GLASS SURROUND, INSTALLER MUST PROVIDE A MEANS OF SECONDARY GUARD, NOT ATTACHED TO, BUT SURROUNDING THE PTO30 BURNER WITH A MINIMUM HEIGHT OF 750MM.
PAGE 21
INSTALLATION NOTE: If using framing unit with original version of PTO30 (not -1), cut base in areas shown below and fold down to allow room for the larger size. Fold 4. Secure all vertical supports (Part B) with two (2) screws each to lower frame (Part A). 5. Place top frame (Part A) on inside tall vertical supports (Part B). 6. Secure in place with two (2) screws for each support Cut Cut Part A Diagram 1 Fold 1.
PAGE 22
INSTALLATION 8. Secure all tall vertical supports (Part B) to Top and Bottom Frame (Part A) with three (3) screws each, Diagram 10 10. Install two (2) headers (Part F) with four (4) screws each to complete frame installation Diagram 13 & 14 Part F If installing optional panels - continue on to next section. OPTIONAL PANELS: 1. Bend tabs on top flange of side panel to 90º. Diagram 11 - Screw Locations 9. Install four(4) short horizontal supports (Part E) - using four (4) screws for each support.
PAGE 23
INSTALLATION 3. Bend tabs flat, the side panel will then be supported to allow the installation of the top panel. Header (Opacity reduced) Flattened Tabs Diagram 3 - Bend tabs ﬂat, panels is supported on headers. 4. Install top panel with six (6) screws in locations shown below.
PAGE 24
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS 1) Read and understand these instructions before operating this appliance. 2) Check to see that all wiring is correct and enclosed to prevent possible shock. 3) Check to ensure there are no gas leaks. FIRST FIRE The first fire in your decorative gas appliance is part of the paint curing process. To ensure that the paint is properly cured, it is recommended that you burn your decorative gas appliance for at least one (1) hours the first time you use it .
PAGE 25
OPERATING INSTRUCTIONS INSTALLATION COPY OF LIGHTING PLATE INSTRUCTIONS The lighting plate is located on the underside of the table top on the unit. FOR YOUR SAFETY READ BEFORE LIGHTING This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or Natural Gas and Propane Installation Codes, CSA B149.1.
PAGE 26
MAINTENANCE MAINTENANCE INSTRUCTIONS 1) Always turn off the gas valve and unplug the batteries before cleaning. For relighting, refer to lighting instructions. Keep the burner and control compartment clean by brushing and vacuuming at least once a year. When cleaning the logs, use a soft clean paint brush as the logs are fragile and easily damaged. 2) Clean off leaves etc. before burning. 3) Clean appliance with a damp cloth (never when unit is hot). Never use an abrasive cleaner.
PAGE 27
MAINTENANCE VALVE ASSEMBLY REPLACEMENT Turn the unit off and allow to cool to room temperature. 9) Remove 10 screws securing valve assembly. 1) Remove table top by lifting up and off, use caution if glass surround is in place. 2) Remove glass crystals, garden stones and logset, if installed. 3) Locate and remove 2 screws at each end of burner assembly - see locations in Diagram 1 below. 10) Lift valve assembly up and out.
PAGE 28
PARTS LIST PARTS Part # 28 Description Part # Description 1 377-024 Burner Tray 9 376-526 Burner 2 377-035 Finishing Trim 10 377-045 Firebox 3 377-026 Mounting Bracket 11 377-046 Controls Enclosure 4 377-034 Pilot Shield 12 377-510 Valve Tray 5 377-027 Burner Mount 13 377-047 Components Cover 6 377-028 Burner Tray End 14 377-048 Pilot Shield support 7 377-030 Offset Bracket 15 377-054 Drainage Bracket 8 376-512 Electronic Assembly Regency Plateau™ PTO30 Outd
PAGE 29
NOTES Regency Plateau™ PTO30 Outdoor Gas Fireplace 29
PAGE 30
NOTES 30 Regency Plateau™ PTO30 Outdoor Gas Fireplace
PAGE 31
WARRANTY Regency® Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully inspects each unit thoroughly before it leaves our facility. FPI Fireplace Products International Ltd. is pleased to extend this limited warranty to the original purchaser of a Regency® Product. This warranty is not transferable.
PAGE 32
Register your Regency® warranty online www.regency-fire.com.au Reasons to register your product online today! • View and modify a list of all your registered products. • Request automatic email notification of new product updates. • Stay informed about the current promotions, events, and special offers on related products. • Help assure you get the most out of your warranty. • Eliminate confusion and frustration if warranty** service is required in the future.