Renata SA Switzerland Engineering Specification Model No. : ICP543759PMT Issued Date : 2011/01/05 Version: V 0.0 Engineering specification subject to changes without notice.
Description Model ICP543759PMT Lithium-ion Polymer Battery Pack Rev. Page Rev.0.0 2/13 1. Preface The purpose of this engineering specification is to provide technical information for the rechargeable Lithium-ion polymer battery pack ICP543759PMT. 2. Description and Model 2.1 Description Rechargeable Lithium-ion Polymer Battery Pack 2.2 Model ICP543759PMT 3. Specifications 3.1 Typical Capacity 3.3 Charging Voltage 1320mAh (at 0.2C rate discharge process after standard charge) 1260mAh (at 0.
Description Model ICP543759PMT 4.Outline Dimension Lithium-ion Polymer Battery Pack Rev. Page Rev.0.0 3/13 See attached drawing for ICP543759PMT (Fig. 1). The thickness is the maximum thickness after 500 cycles. 5. Appearance Free from deformation, damage, noticeable scratch, flaw, rust, discoloration or electrolyte leakage. 6. Standard Test Condition 6.
Rev. Description Model Page ICP543759PMT Lithium-ion Polymer Battery Pack Rev.0.0 4/13 8. Test Procedure and its Standard Item Measuring Procedure Standard 8.1 Appearance Visual No Defects and Leakage 8.2 Dimension Caliper for dimension As item 4 8.3 Weight Balance As item 3.12 8.4 Initial Open Circuit Voltage 8.5 Initial Internal Impedance 8.6 Discharge Capacity Voltmeter 3.7~3.9V Measure the AC impedance at 1kHz ≤320mΩ (50% SOC) 8.7 Maximum Discharge Current Engineering ≧1260mAh (min.
Rev. Description Model ICP543759PMT Lithium-ion Polymer Battery Pack 8.8 Charge/Discharge Cycle Life Rev.0.0 Page 5/13 Discharge capacity should be≧80% of 1st cycle capacity @ 500th cycle. 0.5C Rest for 10 minutes between each Discharge: 0.5C to 3.0V charge/discharge step. 8.9 Leakage Proof The fully charged battery shall be stored at No leakage. 65±3℃and relative humidity 95±5% for 7 days. 8.10 Temperature 1)Charge:CC/CV,CC-0.5C,CV-4.2V Discharge capacities should Cut-off 0.05C at 23±3℃.
Model Rev. Description ICP543759PMT Lithium-ion Polymer Battery Pack Rev.0.0 10. UL 1642 Safety Criteria for Acceptance Item State Test method External Short-circuit Fully Charged Cell terminals are short-circuited for 6 hours or longer with a resistance of 50mΩ or less. Test Tests are to be conducted at room temperature and 55℃. Forced-Discharge Fully Charged Cell is discharged at a current of 1C rate for Test 2.5 hours. (If current stops by safety or passive circuit on the battery, test is finished.
Model Rev. Description Page ICP543759PMT Lithium-ion Polymer Battery Pack Rev.0.0 7/13 11. Battery Pack Safety Criteria Item State Test method Specification Overcharge Test Fully Discharged Test passed according - Fully charge battery pack Settings: CVC mode: 4.2V, time: 300 to test method. min, set charging current (0.8C), cut-off by taper current (or end Current) 0.02C. - Continuously charge battery pack Settings: CVC mode: 4.6V, time: 60 min, set charging current (0.2C).
Model Rev. Description Page ICP543759PMT Lithium-ion Polymer Battery Pack Rev.0.0 8/13 12. Charge State of Battery Before Shipment The battery is charged to approximately 50 % of minimum capacity. Voltage is 3.7V~3.9V. This measuring test should be performed within one month after shipment from our factory. 13. Handling Precautions ICP battery pack shall have enough protection for ICP cell from the specification of electrical, mechanical and environmental characteristics.
Model Rev. Description Page ICP543759PMT Lithium-ion Polymer Battery Pack Rev.0.0 9/13 (6) Don’t drive a nail into a battery, strike it by hammer, walk or step on it. As the battery might be broken or deformed and then it will be short-circuited, it would cause the generating, smoke, rupture or flaming.
Model Rev. Description Page ICP543759PMT Lithium-ion Polymer Battery Pack Rev.0.0 10/13 (2) Don’t get into a microwave or a high pressure container Because of sudden heat or damage of sealing condition of battery, it may cause the generating, smoke, rupture or flaming. (3) Don’t use a leaked battery nearby fire If the liquid leaks from the battery (or the battery gives out bad smell), let the battery leave from flammable objects immediately.
Rev. Page Rev.0.0 11/13 Description Model ICP543759PMT 14. History of Revision Lithium-ion Polymer Battery Pack REV. ISSUE CONTENT OF AMENDMENT PRE. CHK. APP. 0.0 Jan. 05, 2011 1st Edition MKL KS KW End Engineering specification subject to changes without notice.
Model ICP543759PMT Rev. Page Rev.0.0 12/13 Description Lithium-ion Polymer Battery Pack Fig.1 Engineering specification subject to changes without notice.
Rev. Page Rev.0.0 13/13 Description Model ICP543759PMT Lithium-ion Polymer Battery Pack Part list: Item Qty Ref Part name Number Marker 1 1 R1 RES RC03J471G/0603 /470Ω/±5%/1/10W SKYWELL 2 1 R2 RES RC02J102G/0402 /1KΩ/±5%/1/16W SKYWELL 3 1 C1 CAP 0603/0.1µF/+80%-20% /06032E104Z500BA SKYWELL 4 1 C2 CAP 0402/0.