TWINGO DRIVER’S HANDBOOK
RENAULT recommends ELF ELF has developed a complete range of lubricants for RENAULT: f engine oils f manual and automatic gearbox oils Warning: to ensure the engine operates optimally, the use of a lubricant may be restricted to certain vehicles. Please refer to your maintenance document. Benefiting from the research applied to Formula 1, lubricants are very high-tech products.
Welcome to your new vehicle This Driver’s Handbook contains the information necessary: – for you to familiarise yourself with your vehicle, to use it to its best advantage and to benefit fully from the all the functions and the technical developments it incorporates. – to ensure that it always gives the best performance by following the simple, but comprehensive advice concerning regular maintenance. – to enable you to deal quickly with minor faults not requiring specialist attention.
0.
C O N T E N T S Sections Getting to know your vehicle ............................... 1 Driving ................................................................... 2 Your comfort . ........................................................ 3 Maintenance .......................................................... 4 Practical advice ..................................................... 5 Technical specifications . ..................................... 6 Alphabetical index .............
0.
Section 1: Getting to know your vehicle Keys, Remote control: general information, use, deadlocking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic locking when driving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Headrests . . . . . . . . . . . . . . . . . . . . . . . .
KEY/RADIO FREQUENCY REMOTE CONTROL: general information (1/2) Driver’s responsibility A 2 1 3 Never leave your vehicle with the card inside the vehicle and never leave a child (or a pet) unsupervised. With the card in the reader, it would be possible to start the engine or operate electrical equipment such as the electric windows and there is a risk that part of their body may become trapped (neck, arm, hand, etc.). Risk of serious injury.
KEY/RADIO FREQUENCY REMOTE CONTROL: general information (2/2) Radio frequency remote control operating range This varies according to the environment. It is therefore important when handling the remote control to ensure that you do not lock or unlock the vehicle by inadvertently pressing the buttons. Note: on certain vehicles, if a door is not opened within approximately 2 minutes of the door being unlocked by remote control, the doors will lock again automatically.
RADIO FREQUENCY REMOTE CONTROL UNIT: use The doors are locked and unlocked using the remote control unit A. It is powered by a battery which must be replaced (refer to the information on “Radio frequency remote control: batteries” in Section 5). A A 1 Locking the doors Unlocking the doors Press the locking button 1. Press unlocking button 2. The hazard warning lights and indicator lights flash twice to indicate that the doors have locked.
DEADLOCKING To activate deadlocking Press button 1 twice in quick succession. 1 The hazard warning lights and side indicator lights flash five times to indicate that the doors have locked. Deadlocking of the doors/ tailgate (for some countries) This allows you to lock the doors and tailgate and to prevent the doors from being opened with the interior handles (by breaking the window and then trying to open the doors from the inside). Never use deadlocking if someone is still inside the vehicle. 1.
opening and closing the doors Lights-on warning buzzer If you have left the lights on after switching off the ignition, a reminder buzzer will sound when the driver’s door or, depending on the vehicle, the front doors or tailgate are opened (to prevent discharge of the battery, etc.). 1 2 3 Manual locking Opening manually from the inside Pull handle 1. Opening manually from the outside With the key, unlock the front door lock 2. Place your hand under handle 3.
LOCKING/UNLOCKING THE DOORS (1/3) Doors and tailgate status indicator light 1 The indicator light on switch 1 informs you of the closure status of the doors and tailgate: 2 – the indicator light is on when the doors/tailgate are locked; – the indicator light goes out when a door or the tailgate is open (or incorrectly closed). S Electric central locking When you lock the doors using the remote control, the indicator light remains lit for approximately one minute then goes out.
LOCKING/UNLOCKING THE DOORS (2/3) Electric central locking Locking/unlocking from the outside In some cases, the radio frequency remote control may not work: – if the vehicle is located in a zone of high electromagnetic radiation; – if appliances are operating on the same frequency as the remote control (mobile phone, etc.); 1 – if the remote control battery is worn or flat, etc.
LOCKING/UNLOCKING THE DOORS (3/3) Press switch 1 for more than five seconds, then get out of the vehicle with the remote control with you and close the driver’s door. 1 When the door is closed, all the doors and the tailgate will be locked. The vehicle can only be unlocked from the outside with the coded ignition key, for the front left-hand door. Make sure you have your remote control with you before you leave your vehicle.
AUTOMATIC LOCKING WHEN DRIVING You can decide whether you want to activate this function. The door can be unlocked: – by opening a door when stationary. To activate Note: if a door is opened, it will automatically be locked again when the vehicle reaches a speed of approximately 4 mph (7 km/h); With the ignition on, press central door locking button 1 for about 5 seconds, until a double beep is heard.
FRONT HEADRESTS (1/2) A 1 Adjusting the headrest (depending on the vehicle) Fixed, non-adjustable headrest A To raise the headrest Press button 1 and lift the headrest to release it. To refit the headrest The headrest is a safety component. Ensure that it is fitted and in the correct position: the top of your head should be in line with the top of the headrest. Insert the headrest rods into the holes (tilt the seatback backwards if necessary). Push the headrest in until it locks in position.
FRONT HEADRESTS (2/2) To refit the headrest B In case the adjustment of the rods has been modified, pull out the rods 3 as far as they will go (ensure they are aligned and clean). In case of difficulty, ensure the notches face forwards. B 2 3 1 Height adjustable headrest B It can be identified by the presence of button 2. To raise the headrest Slide it upwards to the required height. To lower the headrest Press button 2 and guide the headrest down to the desired height. 1.
FRONT SEATS (1/2) 4 5 1 3 2 Adjusting the height of the driver’s seat (depending on the vehicle) Move lever 3. To move forwards or backwards Move the lever 2 or handle 4 (passenger side) to unlock. Once in the desired position, release the lever or handle and check that the seat is correctly locked. For safety reasons, carry out any adjustments when the vehicle is not being driven.
FRONT SEATS (2/2) 6 4 2 Access to the rear seats Move handle 4 or 6 (depending on the vehicle), move the seat back and slide the seat forwards. To return the seat to its original position (as stored in the memory, depending on the vehicle) on the driver’s side, slide the seat backwards until it locks. Check that no object or person prevents the front seat from locking. If so, remove any obstacles behind the front seats. Adjust the seat to allow sufficient room in the rear.
SEAT BELTS (1/2) Always wear your seat belt when travelling in your vehicle. You must also comply with the legislation of the particular country you are in. Before starting, first adjust your driving position, then ask all occupants to adjust their seat belt to ensure optimum protection. Seat belts which are incorrectly adjusted or twisted may cause injuries in the event of an accident. Use one seat belt per person, whether child or adult. Even pregnant women should wear a seat belt.
SEAT BELTS (2/2) If your seat belt becomes completely jammed: – pull the belt slowly but firmly so that just over 3 cm unwinds; – then allow the seat belt to rewind automatically; – unwind it again; 3 – if there is still a problem, contact an approved Dealer. 4 5 5 Locking Unwind the belt slowly and smoothly and ensure that buckle 3 locks into catch 5 (check that it is locked by pulling on buckle 3). If the belt jams, allow it to return slightly before attempting to unwind it again. 1.
REAR SEAT BELTS 1 2 3 Rear side seat belts The belts are locked, unlocked and adjusted in the same way as the front belts. Rear seat functions: Refer to the information on the “Rear seats: functions” in Section 3. Slowly unwind belt 1. Click buckle 2 into the catch 3. Check that the rear seat belts are positioned and operating correctly each time the rear seats are moved. 1.
SEAT BELTS The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: belts, seats and their mountings. For special operations (e.g. fitting child seats), please contact an authorised dealer. – Do not use devices which allow any slack in the belts (e.g. clothes pegs, clips, etc.): a seat belt which is worn too loosely may cause injury in the event of an accident.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) These are: – Have the entire restraint system checked following an accident. – pretensioners; – force limiters; – No operation whatsoever is permitted on any part of the system (pretensioners, air bags, computers, wiring) and the system components must not be reused on any other vehicle, even if identical. – air bags for driver and front passenger; – side air bags (depending on vehicle).
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. Air bags for driver and front passenger Fitted to the driver and passenger side. The presence of this equipment is indicated by the word “Air bag” on the steering wheel and the dashboard (air bag zone A) and a label on the lower part of the windscreen or on the sun visor.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) 2 Operation The air bag system is only operational when the ignition is switched on. If a severe frontal impact occurs, the air bag(s) deploy(s) rapidly, cushioning the impact of the driver’s head and chest against the steering wheel and the front passenger’s head against the dashboard. The air bag then deflates immediately so that passengers are not impeded in any way when they get out of the vehicle.
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is deployed and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag deploys. Warnings concerning the driver’s air bag – Do not modify the steering wheel or the steering wheel boss. – Do not cover the steering wheel boss under any circumstances.
METHODS OF RESTRAINT IN ADDITION TO THE REAR SEAT BELTS Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. – Have the entire restraint system checked following an accident. – No operation whatsoever is permitted on any part of the system (air bags, electronic control units, wiring) and the system components must not be reused on any other vehicle, even if identical.
SIDE PROTECTION DEVICES Side air bags These air bags may be fitted to the front seats and are deployed at the sides of the seats (door side) to protect the occupants in the event of a severe side impact. A marking on the seat informs you of the presence of this device. Curtain air bags These air bags may be fitted along the top of each side of the vehicle and are triggered along the front and rear side windows to protect passengers in the event of a side impact.
ADDITIONAL methods of RESTRAINT All of the warnings below are given so that the air bag is not obstructed in any way when it is deployed and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag deploys. The air bag is designed to complement the action of the seat belt. The air bag and the seat belt are integral parts of the same protection system. It is therefore essential to wear the seat belt at all times.
Child safety: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehicle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet finished growing. The seat belt alone would not provide suitable protection. Use an approved child seat and ensure you use it correctly.
Child safety: General information (2/2) Using a child seat The level of protection offered by the child seat depends on its ability to restrain your child and on its installation. Incorrect installation compromises the protection it offers the child in the event of harsh braking or an impact. Before purchasing a child seat, check that it complies with the regulations for the country you are in and that it can be fitted in your vehicle.
Child safety: choosing a child seat mounting Rear-facing child seats A baby’s head is, proportionally, heavier than that of an adult and its neck is very fragile. Transport the child in this position as long as possible (until the age of 2 at the very least). It supports both the head and the neck. Choose a bucket type seat for best side protection and change it as soon as the child’s head is higher than the shell. 1.
Child safety: choosing a child seat mounting (1/3) Choosing the attachment There are two ways of attaching child seats: via the seat belt or using the ISOFIX system. Attachment via the seat belt The seat belt must be adjusted to ensure that it is effective in the event of harsh braking or an impact. Ensure that the strap paths indicated by the child seat manufacturer are respected.
Child safety: choosing a child seat mounting (2/3) 1 2 The two rings 1 are located between the seatback and the seat base of the seat or bench seat and are identified by a marking. To ensure your child seat can be easily fitted and locked on rings 1, use access guides 2 on the child seat. The ISOFIX anchorage points have been exclusively designed for child seats with the ISOFIX system. Never fit a different type of child seat, seat belt or other objects to these anchorage points.
Child safety: choosing a child seat mounting (3/3) 3 4 The third ring is used to attach the upper strap on some child seats. Fit the hook of the strap onto ring 3 (for the rear seats) or 4 (for the front seats) and pull the strap. Do not change the position of the seat to which the child/baby seat is fitted after pulling the strap.
child safety: fitting a child seat (1/4) Some seats are not suitable for fitting child seats. The diagram on the following page shows you how to attach a child seat. The types of child seat indicated may not be available. Before using a different child seat, check with the manufacturer that it can be fitted. Fit the child seat in a rear seat wherever possible. Check that when installing the child seat in the vehicle it is not at risk of coming loose from its base.
Child safety: Fitting a child seat (2/4) ³ Check the status of the air bag before fitting a child seat or allowing a passenger to use the seat. Child seat attached using the ISOFIX mounting ü ± Seat which allows an ISOFIX child seat to be fitted. RISK OF DEATH OR SERIOUS INJURY: before installing a rear-facing child seat in the front passenger seat, make sure the air bag has been deactivated (refer to Section 1 “Child safety: front passenger air bag deactivation/activation”).
Child safety: Fitting a child seat (3/4) The table below summarises the information already shown on the diagram on the previous page, to ensure the regulations in force are respected.
Child safety: Fitting a child seat (4/4) X = S eat not suitable for fitting child seats. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. IUF/IL = On equipped vehicles, seat which allows an approved “Universal”/“semi-universal” or “vehicle specific” child seat to be attached using the ISOFIX system; check that it can be fitted.
child safety: deactivating/activating the front passenger airbag (1/3) 1 2 Deactivating the front passenger airbags (on equipped vehicles) In order to fit a child seat to the front passenger seat when this is allowed, you must deactivate the front passenger seat additional restraint devices (side airbags (depending on vehicle), front airbags, etc.). To deactivate the restraint devices supplementary to the front passenger seat belt: switch off the ignition, press and turn lock 1 to the OFF position.
child safety: deactivating/activating the front passenger airbag (2/3) A A A 3 The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. DANGER Since front passenger airbag triggering and the position of a rear-facing child seat are incompatible, NEVER use a restraining device for rearfacing children on a seat with an ACTIVATED AIRBAG in front of it. This provides a risk of DEATH or SERIOUS INJURY to the CHILD. 1.
child safety: deactivating/activating the front passenger airbag (3/3) 1 2 Activating the front passenger air bags You should reactivate the air bag as soon as you remove the child seat from the front passenger seat to ensure the protection of the front passenger in the event of an impact. To reactivate the restraint devices supplementary to the front passenger seat belt: switch off the ignition, press and turn lock 1 to the ON position. With the ignition on, check that the warning light 2 goes out.
AUDIBLE AND VISUAL SIGNALS Depending on the vehicle, the hazard warning lights may come on automatically under deliberate heavy deceleration. 0 2 Direction indicators 1 Horn Press the end of the stalk 1. Headlight flasher Pull stalk 1 towards you to flash the headlights. In this case, the hazard warning lights may be switched off by pressing switch 2 once. Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. é Hazard warning lights Press switch 2.
DRIVING POSITION, LEFT-HAND DRIVE (1/2) 1 2 3 4 5 28 27 26 6 7 8 9 10 11 12 19 25 24 23 22 21 1.
DRIVING POSITION, LEFT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side window demister outlet. 10 Instrument panel. 2 Side air vent. 11 Display: – clock and temperature; – radio, clock and temperature or storage compartment. 3 Stalk: – direction indicator lights; – exterior lights; – front fog lights; – rear fog lights; – horn. 4 Driver’s air bag location, cruise control/speed limiter controls. 5 Rev counter.
DRIVING POSITION, RIGHT-HAND DRIVE (1/2) 1 3 2 27 26 4 25 24 23 5 6 7 8 19 22 21 1.
DRIVING POSITION, RIGHT-HAND DRIVE (2/2) The equipment fitted, described below, DEPENDS ON THE VERSION AND COUNTRY. 1 Side window demister outlet. 11 Rev counter. 2 Side air vent. 12 Stalk for: – direction indicator lights; – exterior lights; – front fog lights; – rear fog lights; – horn. 3 Location for passenger air bag. 4 Windscreen demister outlet. 5 Centre air vents. 6 Instrument panel.
INSTRUMENT PANEL: warning lights (1/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. D Handbrake on and brake circuit incident warning light If it comes on during braking and is ac- A û warning light companied by the and a beep, it indicates that the fluid level in the circuit is low or that there is a braking system fault. Stop as soon as traffic conditions allow and contact an approved dealer.
INSTRUMENT PANEL: warning lights (2/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. À Oil pressure warning light For vehicles equipped with this option, the light comes on when the ignition is switched on then goes out. If it comes on when the vehicle is being If it comes on continuously, consult your approved dealer as soon as possible. û Check the oil level. If the level is normal, the indicator light is being lit by something else.
INSTRUMENT PANEL: warning lights (3/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. x Anti-lock braking warning light This lights up when the ignition is switched on and goes out after a few seconds. If it does not go out when the ignition is switched on, or lights up when driving, there is a fault with the ABS. Braking will then be as normal, without the ABS. Contact an approved dealer as soon as possible.
INSTRUMENT PANEL: warning lights (4/4) The presence and operation of the warning lights DEPEND ON THE EQUIPMENT AND COUNTRY. © Warning light This lights up when the ignition is switched on and goes out after a few seconds. It may come on with other warning lights on the instrument panel. If it lights up when the vehicle is being driven, it is advisable to stop at an approved dealer soon.
INSTRUMENT PANEL: displays and indicators 2 1 3 5 4 Rev counter 1 (graduations x100) (depending on vehicle) Speedometer 2 To change from miles to km/h, refer to the information on the “Trip computer and warning system” in Section 1. Overspeed buzzer Depending on the vehicle, a buzzer sounds for approximately 10 seconds every 30 seconds, as long as the vehicle is travelling in excess of 72 mph (120 km/h). 1.48 Sequential gearbox display 3 This indicates the gear engaged (depending on the vehicle).
TRIP COMPUTER (1/5) 1 Display selection key 1 Instrument panel in miles Press button 2 multiple times to scroll through the following information (depending on the vehicle): It is possible to switch to km/h. – total mileage recorder; – trip mileage recorder; 2 – fuel consumed; – average fuel consumption; – current fuel consumption; – estimated range; – distance travelled; Display 1 General reset and trip mileage recorder reset key 2 Press and hold button 2 to reset the trip mileage recorder.
TRIP COMPUTER (2/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of display selections by repeatedly pressing button 2 Interpreting the display Total mileage recorder. Trip mileage recorder. Speed limiter or cruise control programmed speed. Refer to the information on the “Speed limiter” and “Cruise control” in Section 2. Fuel consumed since the last reset. The value is displayed after having travelled at least 400 metres since the last reset.
TRIP COMPUTER (3/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of display selections by repeatedly pressing button 2 Interpreting the display Average fuel consumption since the last reset. The value is displayed after having travelled at least 400 metres since the last reset. Estimated range with remaining fuel. This range takes into account the average fuel consumption since the last time the reset button was pressed.
TRIP COMPUTER (4/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of display selections by repeatedly pressing button 2 Interpreting the display Clock. Temperature. 1.
TRIP COMPUTER (5/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of display selections by repeatedly pressing button 2 Interpreting the display selected Mileage before service Distance remaining until the next oil change. There are several scenarios: – distance less than 900 miles (1,500 km). It appears on the display for approximately 8 seconds when the ignition is switched on as soon as the distance is less than or equal to 900 miles (1,500 km).
REAR VIEW MIRRORS D A E 2 B 1 3 C Door mirrors with electrical adjustment: Heated door mirrors (depending on vehicle) With the ignition on, position control 1 on: The door mirrors are de-iced when the rear screen demisting/de-icing is active. A to adjust the left-hand door mirror, C to adjust the right-hand door mirror, B to deactivate it. Door mirrors with manual adjustment To adjust the mirror, move lever 2. Interior rear view mirror Its position can be adjusted.
Steering wheel 1 Adjusting the steering wheel Depending on the vehicle, the steering wheel position is adjustable. Hold the steering wheel with one hand, lift lever 1 and position the steering wheel as desired. Lower the lever to lock the steering wheel. Make sure that the steering wheel is correctly locked. For safety reasons, only adjust the steering wheel when the vehicle is stationary. Never leave the steering wheel on full lock when the vehicle is stationary.
CLOCK AND EXTERIOR TEMPERATURE Resetting the clock A 1 Vehicle with button 1: – Press button 1 for approximately three seconds; – when the hour flashes, press button 1 again to adjust it; – wait approximately three seconds, the minutes will flash, press button 1 to adjust them; – wait approximately three seconds, the minutes stop flashing, the time is set. Display A With the ignition on, the time and, depending on the vehicle, the exterior temperature are displayed.
TIME AND EXTERIOR TEMPERATURE (continued) Resetting the clock B H M With the ignition on, press button: H for the hours; M for the minutes. Note: for vehicles which are not fitted with buttons H and M, refer to the specific equipment instructions to discover the special features. External temperature indicator Special note: When the external temperature is between –3°C and +3°C, the °C figures flash (indicates risk of ice formation).
EXTERIOR LIGHTING AND SIGNALS (1/3) 1 2 1 3 u Switching on the side lights Turn the end of stalk 1 until the symbol is opposite mark 2. The instrument panel lights up, the brightness can be adjusted by rotating control 3. 1.58 Adjusting the brightness of the instrument panel lighting Turn control 3 downwards to reduce the brightness and upwards to increase it.
EXTERIOR LIGHTING AND SIGNALS (2/3) 1 2 á Main beam headlights When the dipped beam headlights are lit, pull stalk 1 towards you (an indicator light on the instrument panel lights up). To return to the dipped beam headlight position, pull the stalk towards you. e position. k Lights-on warning buzzer A warning buzzer will sound when the driver’s door is opened and the lights are left on after the ignition has been switched off (to prevent the battery running down, etc.).
EXTERIOR LIGHTING AND SIGNALS (3/3) B A 4 4 5 5 f Rear fog light Turn centre ring 4 on stalk A or B, depending on vehicle, until the symbol faces mark 5. When you release the stalk, it returns to position 0 (stalk B) or remains in rear fog lights position (stalk A). Features of the front and rear fog lights: Operation of the fog lights depends on the exterior lighting selected, and an indicator light will light up on the instrument panel.
ELECTRIC BEAM HEIGHT ADJUSTMENT Examples of positions for adjusting control A according to the load All versions except commercial vehicles Commercial vehicles Driver only 0 _ Driver alone or with front passenger 0 _ Driver with one front passenger and two rear passengers 1 – Driver with three passengers with luggage 2 – Driver with luggage or load reaching the maximum authorised load weight 3 3 A On vehicles fitted with this function, control A allows you to adjust the height of the beams
WINDSCREEN WASH/WIPE (1/2) 2 1 D n stalk 1: A B C Windscreen wiper With the ignition on, move A park; B intermittent wiping: The wipers will pause eral seconds between Depending on the vehicle, sible to change the time sweeps by turning ring 2; for sevsweeps. it is posbetween 1 Special note When driving every time the vehicle stops, the wipers slow down, e.g. fast wiping speed is reduced to normal wiping speed.
WINDSCREEN WASH/WIPE (2/2) In frosty weather, make sure that the wiper blades are not stuck by ice (risk of motor overheating). 1 Windscreen washer Keep an eye on the condition of the blades. Replace the wiper blades as soon as they begin to lose efficiency (approximately once a year). If you switch off the ignition before switching off the windscreen wiper the blades will stop at random on the windscreen. Clean your windscreen regularly. With the ignition on, pull stalk 1 towards you.
REAR SCREEN WASH/WIPE 3 V 3 2 Heated rear screen With the engine running, press button 2 (the integrated indicator on the button will come on). This function demists the rear screen and the electric door mirrors (if these are fitted to the vehicle). The demist function is stopped in two ways: – automatically after 10 minutes of operation; 1 Y timer Speed-dependent rear screen wiper with With the ignition on, turn the end of stalk 1 to align mark 3 with the symbol.
FUEL TANK (1/2) Fuel grade B A Use a high grade fuel with the appropriate octane rating as defined by the particular standards in force in your country. Petrol versions 1 2 It is essential to use unleaded petrol. The octane rating (RON) must conform with the information given on the label inside cover A. Refer to the information on “Engine specifications” in Section 6. Diesel version It is essential to use diesel fuel that conforms with the information given on the label inside cover A.
FUEL TANK (2/2) Filling with fuel Petrol versions Using leaded petrol will damage the antipollution system and may lead to a loss of warranty. To ensure the fuel tank is not filled with leaded petrol, the fuel tank filler neck contains a restrictor fitted with a valve which only allows the nozzle for unleaded petrol to be used (at the pump).
Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in - Ignition switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Starting, stopping the engine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Special features of petrol versions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RUNNING IN/ignition switch Ignition on position M Petrol version Up to 600 miles (1 000 km), do not exceed 78 mph (130 km/h) in top gear or 3,000 to 3,500 rpm. The ignition is switched on: – petrol version: you can start the vehicle; You may only expect top performance from your vehicle after approximately 1,800 miles (3 000 km). – diesel version: the engine is preheating. Service intervals: refer to the Maintenance Service Booklet for your vehicle.
Starting/stopping the engine Starting the engine É Diesel injection indicator light In very cold conditions (temperatures below –20°C): so that it is easier to start the engine, switch on the ignition for several seconds before starting the engine. Turn the ignition key to the “Ignition on” position and hold this position until the preheating indicator light goes out.
special notes on petrol versions The following operating conditions: – driving for long periods when the low fuel level warning light is lit; – using leaded petrol; – using fuel or lubrication additives which are not approved.
SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed Running out of fuel Diesel engines are fitted with injection equipment which prevents the engine speed being exceeded irrespective of the gear selected. If the tank has been completely drained, the system must be reprimed after the tank is refilled: see information on the “fuel tank” in Section 1 before restarting the engine.
GEAR LEVER/POWER-ASSISTED STEERING Vehicles with sequential gearbox: refer to the information on the “Quickshift gearbox” in Section 2. Power-assisted steering Never drive with an inadequately charged battery. Variable power-assisted steering (depending on vehicle) 1 It is equipped with a system which adapts the level of assistance to the vehicle speed.
HANDBRAKE To apply: Pull upwards, check that the vehicle is properly immobilised. 1 To release: Pull the lever up slightly, press button 1 and then lower the lever to the floor. The red warning light on the instrument panel will come on if you are driving with an incorrectly released handbrake. Make sure that the handbrake is properly released when driving (red indicator light off), otherwise overheating, or even damage, may occur.
ADVICE: antipollution, fuel economy and driving (1/3) By virtue of its design, moderate fuel consumption and initial settings, your vehicle conforms to current antipollution regulations. The manufacturer is actively striving to reduce pollutant exhaust gas emissions and to save energy. But the fuel consumption of your vehicle and the level of pollutant exhaust gas emissions are also your responsibility. Ensure that it is maintained and used correctly.
ADVICE: antipollution, fuel economy and driving (2/3) Exhaust gas monitoring system The exhaust gas monitoring system will detect any operating faults in the vehicle’s antipollution system. If this system malfunctions, toxic substances may be released into the atmosphere or damage may occur. Ä This warning light on the instrument panel will indicate if there are any faults in the system: This lights up when the ignition is switched on and goes out when the engine is started.
ADVICE: antipollution, fuel economy and driving (3/3) – For vehicles fitted with air conditioning, it is normal to observe an increase in fuel consumption (especially in city conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required. Advice for reducing consumption and therefore helping to preserve the environment: Drive with the air vents open and the windows closed.
Environment Your vehicle has been designed with respect for the environment in mind for its entire service life: during production, use and at the end of its life. This commitment is illustrated by the of the manufacturer eco² signature. Emissions Manufacture Our vehicles are also equipped with a particle filter system including a catalytic converter, an oxygen sensor and an active carbon filter (the latter prevents vapour from the fuel tank being released into the open air).
Driving correction device Depending on the vehicle, this is composed of: – ABS (anti-lock braking system); – electronic stability program (ESP) with understeer control and traction control (ASR); – emergency brake assist. These functions are an additional aid in the event of critical driving conditions, enabling the vehicle behaviour to be adapted to suit the driving conditions. However, the functions do not take the place of the driver.
Driving correction device (continued) Electronic stability program (ESP) with understeer control and traction control (ASR) Warning light on the instrument panel flashes when the function starts operating. Electronic Stability Program (ESP) Traction control (ASR) This system helps you to keep control of the vehicle in critical driving conditions (avoiding an obstacle, loss of grip on a bend, etc.).
Driving correction device (continued) Special note on vehicles with a Quickshift gearbox Emergency brake assist When driving on some roads with low surface grip (grass, snow, mud, etc.), the system may reduce the engine output to limit wheelspin. If this is not required, it is recommended to switch to manual mode on the Quickshift gearbox (using the gear lever). Operating principle Operating faults When the system detects an operat- and ing fault the warning lights © appear on the instrument panel.
Cruise control - speed limiter: limiter function (1/3) 2 3 4 5 1 The speed limiter function helps you stay within the driving speed limit that you choose, known as the limit speed. 6 Controls 1 Main “On/Off” switch. 2 Limit speed activation, storage and increase switch (+). 3 Limit speed activation, storage and decrease switch (-). 4 Switch the function to standby, with limit speed stored (O). 5 Stored limit speed activation, storage and recall (R).
Cruise control - speed limiter: limiter function (2/3) Varying the limit speed You can vary the limit speed by pressing switch 2 (+) repeatedly to increase the speed or switch 3 (-) to decrease it. 2 3 4 5 Exceeding the limit speed It is possible to exceed the limit speed at any moment. To do this: depress the accelerator pedal firmly and fully (beyond the kickdown point).
Cruise control - speed limiter: limiter function (3/3) Recalling the limit speed If a speed has been stored, it can be recalled by pressing switch 5 (R). 2 3 4 5 1 Putting the function on standby Switching off the function The speed limiter function is deactivated if you press switch 1: in this case a speed is no longer stored. The instrument panel indicator light goes out, confirming that the function is deactivated. The speed limiter function is suspended when you press switch 4 (O).
Cruise control - speed limiter: cruise control function (1/4) 2 1 The cruise control function helps you to maintain your driving speed at a speed that you choose, called the cruising speed. This cruising speed may be set at any speed above 20 mph (30 km/h). 2.18 4 5 This function is an additional driving aid. However, the function does not take the place of the driver.
Cruise control - speed limiter: cruise control function (2/4) 2 3 4 5 1 6 Switching on Press switch 1 on the side showing . Warning light 6 comes on and dashes appear on the instrument panel to indicate that the cruise control function is operating and waiting to store a cruising speed. Activating cruise control Driving At a steady speed (above 20 mph 30 km/h) press switch 2 (+) or 3 (-): the function is activated, the current speed is stored and replaces the dashes on the instrument panel.
Cruise control - speed limiter: cruise control function (3/4) Exceeding the cruising speed 2 3 4 5 The cruising speed may be exceeded at any time by depressing the accelerator pedal. While it is being exceeded, the cruising speed flashes on the instrument panel. Then, release the accelerator: after a few seconds, the vehicle will automatically return to its set cruising speed.
Cruise control - speed limiter: cruise control function (4/4) Returning to the cruising speed 2 3 4 5 If a speed is stored, it can be recalled, once you are sure that the road conditions are suitable (traffic, road surface, weather conditions, etc.). With the vehicle speed above 20 mph (30 km/h), press switch 5 (R). When recalling the stored speed, activation of the cruise control is confirmed by the illumination of the strip around the indicator light.
QUICKSHIFT GEARBOX (1/5) 4 1 2 3 Selector lever 1 Gear shift pattern Display – This allows you to engage first gear, to select reverse and neutral and to change gear in manual mode. A/M to change mode (automatic/ manual) 2 automatic mode – It also allows you to switch between manual and automatic modes at any time, with the engine switched on and a forwards gear engaged, by moving the lever to the left.
QUICKSHIFT GEARBOX (2/5) Operation Starting Switch on the ignition. The display shows N (neutral) and A (automatic mode). The display on the instrument panel switches on. If neutral (N) is displayed, start the engine but do not depress the accelerator. If a gear other than neutral (N) is displayed, it will flash; starting is possible if you depress the brake pedal (indicator light 4 will come on if you forget) when holding the key in the starting position.
QUICKSHIFT GEARBOX (3/5) Driving in automatic mode Changing mode Each time the ignition is switched on, automatic mode is selected by default (letter A on the display). You can change mode at any time by pushing the lever to the left. This switches mode without changing gear. The vehicle is controlled using the accelerator and the brake.
QUICKSHIFT GEARBOX (4/5) Parking Audible warning To park the vehicle with a gear engaged (on a slope, for example): before switching off the engine, check that a gear other than N is displayed on the instrument panel. If you hold the vehicle on a slope for too long without applying the brakes or handbrake you will strain the system and there is a risk that the clutch will overheat. The next time the engine is started, depress the brake pedal.
QUICKSHIFT GEARBOX (5/5) Operating faults Ò When driving, if this warning light comes on together with warning light ©, this indicates a system fault. In most cases, you may still drive the vehicle, although it will not function perfectly. Contact an approved dealer as soon as possible. The vehicle will not start If you cannot start the engine and if the battery is not discharged (display lit up): – Switch on the ignition; – select neutral; – push the vehicle or roll it down a sufficiently steep slope.
Section 3: Your comfort Air vents: air outlets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Manual air conditioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Heating – air conditioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic climate control . . . . . . . . . . . .
AIR VENTS: air outlets (1/2) 1 2 3 7 5 4 6 1 7 1 side window demister outlet 4 centre air vents 2 left-hand side vent 5 control panel 3 windscreen demister outlets 6 right-hand side vent 7 front occupant footwell heater outlets 3.
AIR VENTS: air outlets (2/2) To remove bad odours from your vehicles, only use the systems designed for this purpose. Consult an approved Dealer. 1 3 3 2 4 Side air vents Centre air vents Air flow Air flow Move wheel 2 fully. Move wheel 4 fully. Direction Direction Right/left: move tab 1. Right/left: move tabs 3. Up/down: guide the air vent up or down. Up/down: guide the air vent up or down. : opened to maximum. : closed. : opened to maximum. : closed.
Manual air conditioning (1/3) A B C D E F Distribution of air in the passenger compartment Turn control A. W Close the dashboard vents for more effective demisting. All the air is then directed to the windscreen and front side window demister outlets. i The air flow is distributed between all the air vents, the front side window demisting vents, the windscreen demisting vents and the footwells. Controls A Adjusting the distribution of air in the passenger compartment.
Manual air conditioning (2/3) B Adjusting the ventilation speed C Turn control C from 0 to 4. The passenger compartment is ventilated by blown air. The blower determines how much air enters but vehicle speed has a slight effect on this. The further the control is positioned to the right, the greater the amount of air blown into the passenger compartment. G J The air flow is directed towards the dashboard vents and the footwells. All the air flow is directed to the dashboard vents.
Manual air conditioning (3/3) D Prolonged use of this position (isolation mode) may mist up the windows slightly or cause odours due to the air not being renewed. It is therefore advisable to return to normal operation (external air) by pressing control D when you have passed through the polluted area. Air recirculation operation (isolation of the passenger compartment) Turn control D towards air recirculation symbol â.
heating – air conditioning (1/2) C E Note: The air conditioning may be used in all conditions but does not operate when the external temperature is low. – Button E not activated (indicator integrated into the button not illuminated). The air conditioning is not operating. The heating and ventilation controls are the same as a vehicle without air conditioning. – Button E activated (indicator integrated into the button illuminated). The air conditioning is operating.
heating – air conditioning (2/2) E F If no cold air is produced Check that the controls are set correctly and that the fuses are sound. If they are not, switch off the heating and air conditioning system (indicator integrated into button E) and contact an approved dealer. Adjusting the air temperature. Move control F to obtain the desired temperature. The further the control is in the red, the more the temperature will be increased.
AUTOMATIC CLIMATE CONTROL (1/9) 1 2 3 4 5 6 7 12 Heated rear screen with demisting function and heated door mirrors (depending on vehicle). 8 13 Heated rear screen warning light. 14 Air recirculation control. 14 9 13 12 11 10 The controls 5 Display. 1 Clear View button to demist and de-ice the windows. 6 Automatic mode on and off. 2 Clear View function indicator light. 3 Air conditioning on and off. 4 and 7 Adjusting the air temperature.
AUTOMATIC CLIMATE CONTROL (2/9) 4 6 7 – press button 7 to increase the temperature; – press button 4 to decrease the temperature. Note: The maximum and minimum settings of 15°C and 27°C allow the system to produce a minimum or maximum temperature, whatever the ambient conditions. Ambient temperature: automatic mode Automatic mode Press button 6. Only the temperature and the AUTO symbol are displayed. Functions managed in automatic mode are not displayed.
AUTOMATIC CLIMATE CONTROL (3/9) Ambient temperature: (automatic mode) (continued) Operation To reach and keep the chosen comfort level and to maintain good visibility, the system controls: – ventilation speed; – air distribution; – air recirculation management; – air conditioning start/stop; – air temperature. The displayed temperature values show a comfort level.
AUTOMATIC CLIMATE CONTROL (4/9) 5 Adjusting automatic mode Automatic mode is the normal operating mode of the system (AUTO indicator light lit on display 5) but you may alter the selections made by the system (air distribution, etc.). These options are explained on the following pages.
AUTOMATIC CLIMATE CONTROL (5/9) 5 6 8 ö ó The air flow is directed towards all the air vents and the passenger footwells. The air flow is directed mainly towards the footwells. 10 Distribution of air in the passenger compartment There are five possible combinations for air distribution, which may be selected by pressing buttons 8 and 10 repeatedly. The arrows on display 5 indicate the setting selected: õ ÷ All the air flow is directed to the demisting vents for the windscreen and the side windows.
AUTOMATIC CLIMATE CONTROL (6/9) Varying the ventilation speed In automatic mode, the system uses the most suitable amount of air to reach and maintain the desired comfort level. 3 5 6 Automatic mode is switched off by pressing buttons 9 and 11. 9 These buttons allow you to increase or decrease ventilation speed. Switching air conditioning on or off In automatic mode, the system switches the air conditioning system on or off, depending on the climate conditions.
AUTOMATIC CLIMATE CONTROL (7/9) 13 12 Rear screen de-icing/ demisting With the engine running, press button 12, and operating tell-tale 13 comes on. To exit this function, press button 12 again. Demisting automatically stops by default. This function permits rapid demisting/ de-icing of the rear screen and de-icing of the door mirrors (on equipped vehicles). 3.
AUTOMATIC CLIMATE CONTROL (8/9) 1 2 Note: if you wish to reduce the air flow (which may produce a certain amount of noise in the passenger compartment), press button 11. 6 To exit this function, press either: – button 1 again; – button 6 (the AUTO indicator light on the display will light up). 13 12 Clear View function With the engine running, press button 1, and operating tell-tale 2 comes on. The AUTO button indicator light (on the display) goes out.
AUTOMATIC CLIMATE CONTROL (9/9) 14 Air recirculation mode Pressing button 14 activates air recirculation (the symbol lights up on the display). During recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle. Air recirculation allows the external atmosphere to be cut off (when driving in polluted areas, etc.).
AIR CONDITIONING: information and advice on use Fuel consumption Maintenance It is normal to notice an increase in fuel consumption (especially in towns) when the air conditioning is operating. For vehicles fitted with manual air conditioning, switch off the system when it is not required. Refer to the Maintenance Document for your vehicle for the inspection frequency.
INTERIOR LIGHTING Luggage compartment light (depending on vehicle) 1 2 Press switch 1 for: – continuous lighting; – temporary lighting by opening, depending on the version, one of the front doors or the tailgate. The light only goes out when the doors are correctly closed. – no lighting. Depending on the vehicle, press switch 2, the passenger side map reading light will come on. It comes on when the tailgate or one of the doors is opened.
ELECTRIC WINDOWS With the ignition on: – Press the switch for the window concerned to lower it to the desired height; 1 – lift the switch for the window concerned to raise it to the desired height. 3 2 From the driver’s seat Operate the switches as follows: From the front passenger seat 1 for the driver’s side; Press switch 3. 2 for the front passenger side. Avoid resting any objects against a half-open window: there is a risk that the electric window could be damaged. 3.
manual window winders 1 Manual window winder controls Turn handle 1. Driver’s responsibility Never leave your vehicle with the key inside and never leave a child (or a pet) unsupervised, even for a short while. The reason for this is that the child may endanger himself or others by starting the engine and activating equipment such as the window winders or the sunroof. If a body part gets trapped, reverse the direction of travel of the window as soon as possible by pressing the relevant switch.
SUN VISOR, vanity mirrors 2 3 1 Front sun visor Courtesy mirrors 3 Lower sun visor 1. Depending on the vehicle, the sun visors are fitted with courtesy mirrors, these are concealed behind a cover 2. When driving, ensure the courtesy mirror cover is closed. Risk of injury. 3.
ELECTRIC SUNROOF – Never operate the sunroof with the blind closed; 0 B C 1 1 A – Never drive the vehicle with the sunroof open and the sun blind closed. D 2 This system functions with the ignition on Tilting the sunroof Sun blind – to close: turn button 2 to position 0. Always operate the sun blind with the sunroof closed: – To open: push handle 1 upwards and guide the blind as it retracts; – to close: pull handle 1 until the locks click in place on both sides.
ELECTRIC SUNROOF (continued) Sunroof closing operating fault In this case, check that there is no obstruction, then turn button 2 to position 0, then press button 3, until the sunroof closes completely. 0 Precautions during use – Do not open the sunroof immediately after it has rained or immediately after washing the vehicle.
PASSENGER COMPARTMENT STORAGE/FITTINGS (1/3) 4 1 2 Passenger side glove box 1 To open, lift catch 2. The cover has storage for pens, tickets etc. 3 Dashboard storage compartment 3 Central storage compartment 4 You should avoid keeping liquids in this compartment (if a liquid leaks there is a risk of seepage). Ensure that no hard, heavy or pointed objects are placed in the “open” storage compartments in such a way that they may fall onto passengers during sudden turning or braking. 3.
PASSENGER COMPARTMENT STORAGE/FITTINGS (2/3) 7 6 5 Centre console storage compartment 5 This can be used for storing a mobile ashtray, drinks cans, etc. Nothing should be placed on the floor (area in front of driver) as such objects may slide under the pedal during braking manoeuvres, thus obstructing its use. 3.
PASSENGER COMPARTMENT STORAGE/FITTINGS (3/3) 8 Front seat storage pocket 8 (depending on vehicle) 10 9 Sun visor storage 9 Grab handle 10 Can be used to hold motorway toll tickets, maps, etc. This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle. 3.
Ashtray/cigar lighter/accessories sockets Accessories socket Depending on the vehicle, this is located in the cigar lighter socket 2. 2 1 Ashtray To open, lift cover 1. To empty, pull the ashtray towards you and it will be released from its housing. Cigar lighter Depending on the vehicle, with the ignition on, push in the cigar lighter 2. To use it: consult the instructions for the equipment which should be kept with the other vehicle documentation. It will spring back with a click when it is ready.
REAR HEADRESTS A 1 Position for use To refit the headrest Raise the headrest as far as possible to use it in the high position. Press button A of lock 1 and lower the headrest fully to use it in the low position. Insert the rods in the holes, press button A of the headrest and lower it (move the seat forwards if necessary). To remove the headrest Press button A of lock 1 and remove the headrest (move the seat forwards if necessary).
rear seats: adjustment To adjust the angle of the seatback Pull lever 1. 1 Adjust the angle of the seatback. 2 The rear seats are separate seats. To move forwards or backwards Depending on the vehicle, lift lever 2 to unlock. When the seat is in the required position, release the lever and ensure that the seat is locked in place. When moving the rear seats, check that the anchorage points and rails are clean (they should be free from grit, cloths, toys, etc.) 3.
REAR seats: functions Tension wheels 4 located under each of the rear seats are used to keep the seats folded down. Unhook the tension wheel from ring 5 and hook it to the rods on the headrest in front. 1 2 3 To fold down the rear seats The seats can be folded down in order to transport large objects: From the front, lower the headrest. From the rear, lift handle 2 to fold down the seatback, lower bar 1 of the seat concerned and move it forwards fully.
REAR BENCH SEAT: functions 4 2 1 A 3 The seat and the seatback may be folded away to allow large objects to be transported. To raise the seat Before handling the bench seat, ensure the seat belt catches 1 are attached to the corresponding buckles 2 and ensure the front seats are far enough forward. From the front, lift the seat base 3 against the front seats (movement A). For safety reasons, carry out any adjustments when the vehicle is not being driven. 3.
LUGGAGE COMPARTMENT 2 1 The tailgate is locked and unlocked at the same time as the doors. To open Press button 1 and lift the tailgate. To close Pull down the tailgate using handle 2 inside the tailgate to assist you. Once you have lowered the tailgate, release handle 2 and finish closing the tailgate by pressing down on the tailgate from the outside. 3.
rear parcel shelf (1/2) 4 1 1 5 2 Version with bench seat To remove, unhook the two straps 1. Lift parcel shelf 2. To refit it, proceed in reverse order to removal. 3 6 3 Version with seats To remove (bulky loads): – Unhook both straps 3; – remove the pivots 4 from their housing; – unclip the parcel shelf 5. To refit: Do not place any objects, especially heavy or hard objects, on the rear parcel shelf.
rear parcel shelf (2/2) 7 8 Transporting objects Objects loaded must not protrude beyond area 7 (refer to the information on “Transporting objects in the luggage compartment” in Section 3). If they do, it is essential to remove the parcel shelf. Rear seats moved back fully When the seatbacks are reclined 8 beyond area 7, it is essential to remove the parcel shelf. This prevents contact with the seat or a passenger’s head when the tailgate is shut. The illustration above will remind you to take care. 3.
LUGGAGE COMPARTMENT COVER: utility versions The luggage cover consists of three rigid sections. It can be used in one of three ways: – The luggage compartment cover is in the unfolded position or the semifolded position. Do not place any objects, especially heavy or solid objects on the luggage compartment cover. These may pose a risk to the vehicle occupants if the driver has to brake suddenly or if the vehicle is involved in an accident. 3.36 – The luggage cover is removed.
TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT A B Locations for anchorage points (depending on the vehicle) These are for securing items transported in the luggage compartment (refer to the information on “Transporting objects in the luggage compartment”).
TOWING: towing equipment A A = 600 mm. Permissible nose weight, maximum permissible towing weight braked and unbraked: Refer to the information on “Weights” in Section 6. If the towbar ball obscures the registration plate or the rear lights, it should be removed when not in use. In all cases, comply with local legislation. 3.38 Refer to the manufacturer’s instructions for information on how to fit and operate the towing equipment.
ROOF BARS 1 2 3 4 When fitting roof bars, at the front of the vehicle, replace the blanking bolts with the mounting bolts supplied with the roof bars. Behind seal 3, position the roof bars in the reinforced area 4 provided. Accessing the mounting points Open the doors. Behind seal 2 are blanking bolts 1 which protect the mounting bolt locations. Once they are secured on to the vehicle, the mounting bolts should never be removed (risk of damaging the vehicle).
multimedia equipment 1 3 3 2 The presence and location of this equipment depends on the vehicle’s multimedia equipment. 1 Radio; 2 Steering column control; 3 Microphone. Hands-free telephone integrated control On equipped vehicles, use microphone 3 and steering column control 2. Using the telephone To use this equipment, consult the instructions for the equipment which should be kept with the other vehicle documentation. 3.
Section 4: Maintenance Bonnet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Engine oil level:. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . general information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . topping up/filling. . . . . . . . . . . . . . . . .
BONNET (1/2) 1 To open the bonnet, pull handle 1. 2 Unlocking the bonnet catch To open, push tab 2 to the left as you open the bonnet. When working in the engine compartment, ensure that the windscreen wiper stalk is in the park position. Risk of injury. 4.2 The engine may be hot when carrying out operations in close proximity. In addition, the engine cooling fan can come on at any moment. Risk of injury.
BONNET (2/2) Closing the bonnet 3 Before closing the bonnet, check to make sure that nothing has been left in the engine compartment. 4 5 Opening the bonnet Lift the bonnet and release stay 4 from its holder 5. For your own safety, it is very important to fix the stay into retainer 3 in the bonnet. In the event of even a slight impact involving the radiator grille or bonnet, have the bonnet lock checked by an approved dealer as soon as possible. To close the bonnet, replace stay 4 in holder 5.
ENGINE OIL LEVEL: general information It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level between oil changes. However, contact an approved dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period. B A The oil level should only be read with the dipstick as explained above. If the oil level exceeds the maximum level, do not start your vehicle and contact an approved Dealer.
ENGINE OIL LEVEL: topping up/filling (1/2) 1 1 A 2 2 Special features of 1.2 16V engines To unclip the dipstick, lever it by hand while pressing engine cover A. Topping up/filling The vehicle must be parked on level ground and the engine should be cold (for instance, before the engine is started up for the first time in the day). Do not exceed the max level and do not forget to refit cap 1 and dipstick 2.
ENGINE OIL LEVEL: topping up/filling (2/2)Engine oil change Oil change Service interval: refer to the Maintenance Service Booklet for your vehicle. Average capacities for oil change (including oil filter for information). 1.2 16V engine: 4.35 litres 1.5 dCi engine: 4.4 litres Filling: take care when topping up the oil that no oil drips onto engine components - risk of fire. Remember to refit the cap securely as there is a risk of fire if oil splashes onto hot engine components.
LEVELS (1/3) 1 Level Topping up It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “MIN” warning line on the reservoir 1. After any operation on the hydraulic circuit, a specialist must replace the fluid. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking procedure from our network or from the manufacturer’s web site.
LEVELS (2/3) Replacement intervals Checking intervals Refer to the Maintenance Document for your vehicle. Check the coolant level regularly (very severe damage is likely to be caused to the engine if it runs out of coolant). 2 If the level needs to be topped up, only use products approved by our Technical Department which ensure: – protection against freezing; – anticorrosion protection of the cooling system.
LEVELS (3/3)/Filters Jets To adjust the angle of the jets, pivot the little ball using a pin. 3 Filters The replacement of filter elements (air filter, passenger compartment filter, diesel filter, etc.) is scheduled in the maintenance operations for your vehicle. Replacement intervals for filter elements: refer to the maintenance Document for your vehicle. NOTE Windscreen washer reservoir Filling With the engine switched off, open cap 3, fill until you can see the fluid, then refit the cap.
Tyre pressure (1/2) F: tyre pressures for the rear wheels (motorway). A G: tyre pressure for the emergency spare wheel. H: dimensions of the emergency spare wheel tyre. A B C E H Label A Open the driver’s door to read it. Tyre pressures should be checked when the tyres are cold. If the tyre pressures cannot be checked when the tyres are cold, increase the pressures from 0.2 to 0.3 bar (or 3 PSI). Never deflate a hot tyre. B: dimension of the tyres fitted to the vehicle. 4.
Tyre pressure (2/2) Tyre safety and use of snow chains Refer to the information on “Tyres” in Section 5 for the servicing conditions and, depending on the version, the use of chains. Special note For vehicles used fully laden (maximum permissible all-up weight) and towing a trailer. The maximum speed must be limited to 60 mph (100 km/h) and the tyre pressure increased by 0.2 bar. Refer to the information on “Weights” in Section 6.
BATTERY B 2 3 4 1 A 7 Battery Battery access: Depending on the vehicle, this is located underneath cover 1. Depending on the vehicle, unclip cover A. Handle the battery with care as it contains sulphuric acid which must not come into contact with the eyes or skin. If it does, wash the affected area with plenty of cold water. If necessary, consult a doctor. Ensure that naked flames, red hot objects and sparks do not come into contact with the battery as there is a risk of explosion. 4.
Bodywork maintenance (1/2) A well-maintained vehicle will last longer. It is therefore recommended to maintain the exterior of the vehicle regularly. Your vehicle has been treated with very effective anti-corrosion products. It is nevertheless subject to various outside influences. Corrosive agents in the atmosphere – atmospheric pollution (built-up and industrial areas), – saline atmospheres (near the sea, particularly in hot weather), – seasonal and damp weather conditions (e.g.
Bodywork maintenance (2/2) Respect local regulations about washing vehicles (e.g. do not wash your vehicle on a public highway). Observe the vehicle stopping distances when driving on gravelled surfaces to prevent paint damage. Repair, or have repaired quickly, areas where the paint has been damaged, to prevent corrosion spreading. Remember to visit the body shop periodically in order to maintain your anti-corrosion warranty. Refer to the Maintenance Document.
INTERIOR TRIM MAINTENANCE (1/2) A well-maintained vehicle will have a longer service life. It is therefore advisable to maintain the vehicle interior regularly. Stains should always be dealt with quickly. Whatever type of stain is on the trim, use soapy water (if possible, warm water) containing: Do not use detergents (washing up liquid, powdered products, alcoholbased products, etc.). Use a soft cloth. Glass instrument panel (e.g.: instrument panel, clock, exterior temperature display, radio display).
INTERIOR TRIM MAINTENANCE (2/2) Removing/refitting factory fitted removable equipment in the vehicle If you need to remove equipment to clean the passenger compartment (e.g. mats), always make you refit it properly and on the correct side (driver’s side mats must be fitted on the driver’s side, etc.), using retaining components supplied with the equipment (e.g. the driver’s side mat must always be secured using prefitted retaining devices).
Section 5: Practical advice Puncture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tyre inflation kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tool kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wheel trim – Wheel rims.
Puncture 3 2 A 1 4 In the event of a puncture, depending on the vehicle, you will have: An emergency spare wheel or tyre inflation kit (refer to the information on the following pages). – remove the jack from its storage space A; – unscrew the central mounting 4; – remove the tool kit 3 lifting it from both sides; – remove emergency spare wheel 2. Emergency spare wheel 2 This is located in the luggage compartment.
TYRE PRESSURE KIT (1/3) B A Do not attempt to use the inflation kit if the tyre has been damaged as a result of driving with a puncture. The kit is only approved for inflating the tyres of the vehicle originally equipped with the kit. You should therefore carefully check the condition of the tyre sidewalls before any operation. It must never be used to inflate the tyres of another vehicle, or any other inflatable object (rubber ring, rubber boat, etc.).
TYRE PRESSURE KIT (2/3) With the engine running and the parking brake applied, – unroll the hose from the container; 1 8 2 7 6 5 4 3 Depending on the vehicle, in the event of a puncture, use the kit located in the boot or underneath the luggage compartment carpet. Before using this kit, park the vehicle at a sufficient distance from traffic, switch on the hazard warning lights, apply the handbrake, ask all passengers to leave the vehicle and keep them away from traffic. 5.
TYRE PRESSURE KIT (3/3) 1 – Affix the driving recommendation label to the dashboard where it can easily be seen by the driver; – Put the kit away. – At the end of this initial inflation operation, air will still escape from the tyre. You must drive a short distance in order to seal the hole. – Start immediately and drive at between 12 and 40 mph (20 and 60 km/h) in order to distribute the product evenly in the tyre and, after driving for 2 miles (3 km), stop and check the pressure.
TOOL KIT Hubcap tool 5 or 6 3 4 3 This tool is used to remove the wheel trims. Jack 3 1 Remove jack 3. 7 5 2 When replacing the jack, fold it correctly and position the wheelbrace correctly before replacing it in its position. 6 Tool kit 3 is located in the emergency spare wheel. It consists of a set of tools for various operations on the vehicle: a jack and wheelbrace, towing hitch, etc., and a space for a spare bulb box.
WHEEL TRIM - WHEELS 4 1 C 3 B 2 D A 6 5 Wheel trim (example: wheel trim 1) Central wheel trim (example: wheel trim 4) Remove the wheel trim using hubcap tool 3 (stored in the tool kit) by engaging the hook in the opening for valve 2. Remove the wheel trim using hubcap tool 5 (located in the tool kit) inserting the tool into recess 6. To refit it, align it with valve 2. To refit it, position it in line with recess 6 and tighten it with tool 5.
changing a wheel (1/2) 1 Start extending jack 2 by hand, turning the handle. Position the head correctly under vertical sill seam 3 nearest to the wheel concerned and marked by an oblong hole. Continue turning the handle to position the baseplate of the jack on the ground correctly. 3 2 Switch on the hazard warning lights.
changing a wheel (2/2) Fit the emergency spare wheel on the central hub and turn it to locate the mounting holes in the wheel and the hub. If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel. Tighten the bolts, checking that the wheel is correctly positioned on its hub and unscrew the jack.
TYRES (1/3) Tyre and wheel safety 1 The tyres are the only contact between the vehicle and the road, so it is essential to keep them in good condition. You must make sure that your tyres conform to local road traffic regulations. 2 When the tyre tread has been worn to the level of the warning strips, they become visible 2: it is then necessary to replace your tyres because the tread rubber is now only 1.6 mm deep at most, resulting in poor road holding on wet roads.
TYRES (2/3) Tyre pressures Tyre pressures must be adhered to (including the emergency spare wheel). Pressures must be checked at least once a month and always before a long journey (refer to the information on “Tyre pressures”). Pressures should be checked when the tyres are cold; ignore higher pressures which may be reached in hot weather or following a fast journey. If tyre pressures cannot be checked when the tyres are cold, the normal pressures must be increased by 0.2 to 0.3 bar (or 3 PSI).
TYRES (3/3) Use in winter – Chains For safety reasons, fitting snow chains to the rear axle is strictly forbidden. Chains must not be fitted to tyres which are larger than those originally fitted to the vehicle. – Snow or winter tyres We would recommend that these be fitted to all four wheels to ensure that your vehicle retains maximum adhesion.
WINDSCREEN WIPER BLADES Replacing rear screen wiper blade 6 1 2 5 3 4 Replacing windscreen wiper blades 1 – Lift the windscreen wiper arm 3 as far as it will go (the arm does not lift up completely); 6 – Lift wiper arm 5; – pivot the blade until some resistance is met; – remove the blade by pulling it. Refitting a front or rear wiper blade To refit the wiper blade, proceed in reverse order to removal. Make sure that the blade is correctly locked in position.
FRONT HEADLIGHTS: changing bulbs (1/2) 2 1 The following bulbs can be replaced. However, we would advise you to have them replaced by an authorised dealer if it proves difficult. To return it, proceed in the reverse order to removal. It is recommended that the headlights be adjusted after this operation. 4 3 Main beam headlights, dipped beam headlights – remove bulb holder 1 from its housing without pulling on the cable; – remove cover 2; – release the spring 3; – change the bulb 4.
FRONT HEADLIGHTS: changing bulbs (2/2) 5 4 3 Direction indicator lights Changing a bulb – unclip cover 3 and remove it; – turn bulb holder 4 anticlockwise; – change the bulb 5. Bulb type: PY21W. The bulbs are under pressure and can break when replaced. To return it, proceed in the reverse order to removal. When the bulb has been changed, make sure you refit the cover 3 correctly.
FOG LIGHTS, FRONT SIDE LIGHTS: changing bulbs 4 6 7 1 5 3 2 Front fog lights 1 and front side lights 2 Any operation on (or modification to) the electrical system must be performed by an approved Dealer since an incorrect connection might damage the electrical equipment (harness, components and in particular the alternator). In addition, your Dealer has all the parts required for fitting these units. 8 Turn light trim 3 remove it.
REAR LIGHTS: changing bulbs (1/4) 3 1 2 2 4 5 Rear side lights and stop light, indicator lights and fog lights Unclip the bulb holder using tabs 2. 4 Indicator Orange pear-shaped, bayonet type PY 21 W bulb. Note the correct positioning of the wiring 1 before removal in order to position correctly when refitting. 5 Fog light Pear-shaped, bayonet type P 21W bulb Remove screw 2 and detach the rear light cluster from the outside. The bulbs are under pressure and can break when replaced.
REAR LIGHTS: changing bulbs (2/4) 8 7 6 Reversing lights 6 Lift the boot lid. 9 Unclip covers 7 and remove them. Turn bulb holder 8 fully anticlockwise and change the bulb 9. To reassemble, proceed in the reverse order to removal. When the bulb has been changed, make sure you refit the cover 7 correctly. 6 Reversing lights Bulb type: W16W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
REAR LIGHTS: changing bulbs (3/4) 11 10 High-level brake light – Remove the blanking covers 10 inside the tailgate. – Press the tabs (using a flat-blade screwdriver or similar) as shown. 12 To return it, proceed in the reverse order to removal. Check the tabs are correctly locked in position. Bulb type: W16W. – Remove the brake light from its housing, remove connector 11 and replace bulb 12. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
REAR LIGHTS: changing bulbs (4/4) 13 14 Number plate lights Unclip the light by pressing tab 13 (using a flat-blade screwdriver or similar). Disconnect the light, then remove the cover to access bulb 14. Bulb type: W5W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
INDICATOR LIGHTS: changing bulbs 1 Unclip indicator light 1 (using a flatblade screwdriver or similar) with care. 2 Turn bulb holder 2 a quarter of a turn and take out the bulb. Bulb type: WY 5 W. The bulbs are under pressure and can break when replaced. Risk of injury. 5.
INTERIOR LIGHTS: changing bulbs (1/2) 1 3 2 4 Courtesy light Unclip (using a flat-blade screwdriver or similar 1) the transparent cover 2 in the direction shown. Remove bulb 3 or depending on the vehicle, bulbs 3 and 4. Bulb type: W5W The bulbs are under pressure and can break when replaced. Risk of injury. 5.
INTERIOR LIGHTS: changing bulbs (2/2) 5 Luggage compartment light 5 Unclip light 5 by pressing the tabs on each side (using a flat-blade screwdriver or similar). 6 7 Press tab 6 to release the lens and access bulb 7. Bulb type: W5W. Disconnect the light. 5.
BATTERY: troubleshooting To avoid all risk of sparks: – Ensure that any consumers are switched off before disconnecting or reconnecting the battery; – When charging, stop the charger before connecting or disconnecting the battery. Only a fully charged and well-maintained battery will have a long and useful service life and enable you to start the vehicle’s engine normally. The battery must be kept clean and dry.
BATTERY: troubleshooting (continued) Starting the vehicle using the battery from another vehicle Proceed as follows when starting your vehicle from another vehicle’s battery: Obtain suitable jump leads (large) from an approved Dealer or, if you already have jump leads, ensure that they are in perfect condition. The two batteries must have an identical nominal voltage of 12 volts.
RADIO FREQUENCY REMOTE CONTROL: BATTERIES 1 3 2 Replacing the battery Remove screw 1, open the case at slot 2 using a coin, and replace battery 3 using a flat-blade screwdriver or similar observing the polarity shown on the back of the cover. Note: It is not advisable to touch the electronic circuit in the key cover when replacing the battery. The batteries are available from approved Dealers, and their service life approximately two years.
FUSES (1/3) 3 1 2 Fuse box Clip 3 If electrical equipment does not work, check the condition of the fuses. Remove the fuse using tweezers 3, located on the back of cover 1 or in glove box 2. Depending on the vehicle, open cover 1 to the left of the steering wheel or glovebox 2. To locate the fuses, use the fuel allocation label (covered in the pages that follow). It is not advisable to use the free fuse locations.
FUSES (2/3) Allocation of fuses (the presence of fuses DEPENDS ON THE EQUIPMENT LEVEL OF THE VEHICLE) Numbers 1 and 2 3 Allocation Windscreen wipers/ Rev counter. Power-assisted steering. 4, 16 and 27 Sequential gearbox. 5 Brake light/Speed limiter. 6 Reversing light/Rear view mirror control/ Alarm siren/Parking distance control. 7 5.28 Numbers 11 12 13 Allocation Direction indicator lights/Diagnostic socket. Power supply/ Instrument panel. Dipped beam headlights/Rear fog light.
FUSES (3/3) Allocation of fuses (the presence of fuses DEPENDS ON THE EQUIPMENT LEVEL OF THE VEHICLE) Numbers Allocation Numbers Allocation 33 Left-hand main beam headlight and instrument panel indicator light. 42 Right-hand side light/Passenger compartment instrument lighting 34 Right-hand dipped beam headlight. 43 Left-hand side light. 35 Left-hand dipped beam headlight and instrument panel indicator light. 44 Location reserved for additional equipment. 45 Driver’s door switch.
TOWING: breakdown 1 2 3 5 4 The steering wheel must be unlocked and the ignition key must be in the “Ignition on” position to provide signals (brake lights and direction indicators) on the towed vehicle. At night the vehicle must have its lights on. Use only the towing points at the front 2 and rear 5 (never use the drive shafts). These towing points may only be used for pulling the vehicle, never for lifting it either directly or indirectly.
TOWING: breakdown (continued) – Use a rigid towing bar. If a rope or cable is used (where the law allows this), the vehicle being towed must be able to brake. – A vehicle must not be towed if it is not fit to be driven. – Avoid accelerating or braking suddenly when towing, as this may result in damage being caused to the vehicle. – When towing a vehicle, it is advisable not to exceed 15 mph (25 km/h). When the engine is stopped, steering and braking assistance are not operational. 5.
FITTING THE RADIO 2 1 3 Radio location 1 Tweeter speakers Front door speakers 3 Unclip and remove the cover. The aerial (depending on vehicle), + and – supply connectors and left-hand and righthand speaker wires are fixed to the rear face of the cover. Using a flat-blade screwdriver or similar, unclip grille 2 to access the speaker wires. Consult an approved dealer.
FITTING THE RADIO (continued) 5 4 Speakers in rear panels 4 Location of aerial 5 Consult an approved dealer. Consult an approved dealer. (depending on vehicle) (depending on vehicle) – In all cases, it is very important to follow the manufacturer’s instructions carefully. – The specifications of the brackets and wires (available at approved accessory outlets) vary depending on the equipment level of your vehicle and the type of radio. Consult an approved dealer to find out the correct part number.
ACCESSORIES Electrical and electronic accessories Before installing this type of accessory, make sure it is compatible with your vehicle. You can get advice from an authorised dealer. Connect accessories with a maximum power of 120 watts only. Fire hazard. No work may be carried out on the vehicle’s electrical or radio circuits, except by authorised dealers: an incorrectly connected system may result in damage being caused to the electrical equipment and/or the components connected to it.
OPERATING FAULTS (1/5) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact a RENAULT Dealer as soon as possible. The starter is activated POSSIBLE CAUSES WHAT TO DO The indicator lights fail to light up and the starter does not turn. Battery terminals disconnected, oxidised or incorrectly secured. Retighten, reconnect or clean them if they are oxidised. Battery discharged or unserviceable.
OPERATING FAULTS (2/5) On the road POSSIBLE CAUSES WHAT TO DO Coolant boiling in the coolant reservoir. Mechanical fault: cylinder head gasket damaged, faulty coolant pump. Stop the engine. Contact an approved Dealer. Smoke under the bonnet. Short circuit or cooling system leak. Stop, switch off the ignition, stand away from the vehicle and contact an approved Dealer. while cornering or braking The level is too low.
OPERATING FAULTS (3/5) On the road POSSIBLE CAUSES WHAT TO DO Vibrations Tyres not inflated to correct pressures, incorrectly balanced or damaged. Check the tyre pressures: if this is not the problem, have them checked by an approved dealer. whistling roof aerial incorrectly positioned Fold down the aerial until the end of it is approximately 44 cm from the vehicle’s roof. Steering becomes heavy. Assistance overheating. Leave to cool. Low battery. Recharge or replace the battery.
OPERATING FAULTS (4/5) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved Dealer. The wiper does not stop. Faulty electrical controls. Consult an approved Dealer. Direction indicators flashing more quickly. Blown bulb. Replace the bulb. The direction indicators do not work. Faulty electrical circuit. Consult an approved Dealer.
OPERATING FAULTS (5/5) Electrical equipment The sunroof does not open/close. POSSIBLE CAUSES WHAT TO DO Sunroof opening conditions not fulfilled. Apply the opening conditions (refer to the information on the “Electric sunroof” in Section 3). Roof fault. Leave the sunroof closed or close it using the methods described in “Electric sunroof: Operating fault” in Section 3 and contact your approved dealer. Electrical fault (discharged battery, etc.). 5.
5.
Section 6: Technical specifications Vehicle identification plates. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.2 Engine specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.4 Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6.5 Weights. . . . . . . . .
VEHICLE IDENTIFICATION PLATES (1/2) A A 10 1 2 3 4 5 6 9 7 8 The information shown on the vehicle identification plate should be quoted on all correspondence or orders. The presence and location of the information depends on the vehicle. B 6.2 Vehicle identification plate A 1 Manufacturer name. 2 EC design number or approval number. 3 Identification number. Depending on the vehicle, this information is also given on marking B. 4 MAM (Maximum Authorised Mass) for front axle.
VEHICLE IDENTIFICATION PLATES (2/2) C 1 2 3 C C Quote the details given on engine plate C on all communication or orders. C - Engine plate or engine label (location varies depending on engine) 1 Engine type 2 Engine suffix 3 Engine number 6.
ENGINE SPECIFICATIONS Engine type (see engine plate) Cubic capacity (cc) Type of fuel D4F K9K 1 149 1 461 It is essential to use unleaded petrol of the Octane Rating stated on the label inside the fuel filler flap. If not available, for a limited time only, unleaded fuel may be used: – with an octane rating of 91 for a label showing 95 or 98; – with an octane rating of 87 for a label showing 91, 95 or 98. Spark plugs 6.4 Only use the spark plugs specified for your vehicle’s engine.
DIMENSIONS (in metres) 0.767 2.367 0.553 3.687 1.400 / 1.414 1.949 1.470 (1) 1.386 / 1.400 (1) unladen 6.
WEIGHTS (in kg) The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Consult your approved Dealer.
Replacement parts and repairs Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order. 6.
Service sheets VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Comments/miscellaneous Service □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (continued) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Comments/miscellaneous Service □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (continued) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Comments/miscellaneous Service □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (continued) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Comments/miscellaneous Service □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (continued) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Comments/miscellaneous Service □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
service sheets (continued) VIN: .................................................................................. Date: Miles (km): Invoice number: Type of operation: Stamp Comments/miscellaneous Service □ ....................................... □ Anticorrosion check: OK □ Not OK* □ *See specific page Date: Miles (km): Invoice number: Type of operation: Stamp Service □ Comments/miscellaneous .......................................
Anticorrosion check If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (continued) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (continued) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Anticorrosion check (continued) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.
Anticorrosion check (continued) If the continuation of the warranty is subject to repair, it is indicated below. VIN: .......................................................... Corrosion repair operation to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Date of repair: 6.
Alphabetical index (1/5) A ABS........................................................................2.12 → 2.14 accessories........................................................................ 5.34 accessories socket............................................................. 3.28 additional methods of restraint........................................... 1.25 to the front seat belts........................................1.19 → 1.22 additional systems to the seat belts........................ 1.
Alphabetical index (2/5) emergency braking.................................................2.12 → 2.14 emergency key..................................................................... 1.2 emergency spare wheel................................................ 5.2, 5.6 engine technical specifications................................................... 6.4 engine immobiliser (switch).................................................. 2.2 engine oil................................................................
Alphabetical index (3/5) L levels: engine oil............................................................... 4.5 – 4.6 lighting: exterior..............................................................1.58 → 1.60 interior....................................................... 3.19, 5.22 – 5.23 lights changing bulbs................................................... 5.14 – 5.15 front.................................................................... 5.14 – 5.15 lights: brake lights............................
Alphabetical index (4/5) rear seats........................................................................... 3.31 functions....................................................................... 3.31 rear view mirrors................................................................. 1.54 remote control door locking unit.................................1.2 → 1.4 remote control electric door locking batteries........................................................................ 5.
Alphabetical index (5/5) W warning buzzer................................................................... 1.48 warning lights.........................................................1.44 → 1.47 washing................................................................... 4.13 – 4.14 weights................................................................................. 6.6 wheelbrace........................................................................... 5.6 wheels (safety)..............................
( www.e-guide.renault.com ) RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL.
