User manual
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2016 by Conrad Electronic SE. 1432725_V1_0716_02_VTP_m_en
Settings and Operation
When you turn the PIR sensor to the left while facing the PIR sensor, you will see
two rotary knobs. These are used to adjust the power-on time and the brightness
threshold in regard to the activation of the lights.
a) Adjust the power-on time (knob with time symbol)
Use this knob to set the duration for the power-on time (a duration of 10 ±5 seconds to 4
±1 minutes can be set). Turning it to the left in a counter-clockwise direction will reduce the
power-on time, while to the right in a clockwise direction will extend the duration.
If the PIR sensor detects a heat change again in the detection range within the on-
time cycle, the power-on time will restart anew.
Only if no more heat changes are detected in the detection range during on-time will
the LED outdoor spotlight go out.
b) Setting the switching threshold for the ambient brightness (rotary knob
with sun/moon icon)
With this knob you can set the switching threshold for ambient brightness that enables the PIR
sensor and turns on the LED outdoor spotlight in case of a heat change in the detection range.
Turning the rotary knob counter-clockwise to the left, in the direction of the moon symbol,
means the PIR sensor is activated when it gets darker; turning it clockwise to the right, in direc-
tion of the sun symbol, activates the motion detector in brighter conditions.
c) Alignment of the PIR Sensor
The horizontal detection angle of the PIR-Sensor is 130°, the
vertical detection angle 60°.
By turning the PIR sensor to the left or to right, you can ad-
just the horizontal detection range according to local circum-
stances.
A small round mark on the front of the PIR sensor
(see arrow in the picture on the right) shows you the
centre of the horizontal detection angle.
d) Alignment of the two lamp heads
Both lamp heads can be swivelled individually to the left and right and also up and down;
moreover, the entire lamp head can be rotated. That way, you can adjust the area which should
be illuminated in the best way.
Functional test
For a functional test for the switching threshold of ambient brightness turn the rotary knob all
the way into the direction of sun icon. The knob for the power-on time should be in the base
position (turn in a counter-clockwise direction all the way to the left until it stops).
Now cross the detection range. The two lights of the LED out-
door spotlight will turn on when the PIR sensor detects a heat
change in the detection area.
Each time a heat change is detected, a red LED at the front
of the PIR sensor ashes briey, see arrow in the picture on
the right.
When you stand still (and the PIR sensor can no longer de-
tect any heat changes), both lights should go out after a few
seconds.
Care and Cleaning
• Use a dry, lint-free cloth to clean the product.
• Never use abrasive cleaning agents, cleaning alcohol or other chemical solutions, since
these could damage the housing or even impair operation.
Disposal
Electronic devices are recyclable material and do not belong in the household
waste. Dispose of an unserviceable product in accordance with the relevant statu-
tory regulations.
Technical Data
Operating voltage .................................220 - 240 V/AC, 50Hz
Standby power draw ............................. <1 W
Power consumption ..............................12.5 W
Protection class ....................................II
Protection type ......................................IP44
LED lamps ............................................2, each 10 x 0.5 W
The LEDs are permanently mounted and cannot be replaced.
Luminous ux .......................................900 lm
Light colour ...........................................6000 K ±500 K (cold white)
Light angle ...........................................120°
Swivel range each lamp .......................±45°
Rotary range each lamp .......................±45°
Rotary range lamp heads .....................±125° (for both lamps)
Power-on time ......................................adjustable, 10 ±5 s.....4 ±1 min
PIR range ............................................. up to approx. 8 m (see chapter „PIR Sensor Function“)
PIR detection angle ..............................130° horizontal, 60° vertical
PIR rotation range ...............................±130°
Operation/storage conditions ................temperature: -20 °C to +40 °C
Dimensions ........................................... 147 x 134 x 160 mm (W x D x H)
Weight ..................................................609 g