User manual

ManualsBrandsRENKFORCE ManualsCar Mobile Phone AccessoriesSuction cup Car mobile phone holder 360° swivel

Operating instructions

Car holder for iPhone 6, black

Item no. 1366946

Intended use

Use this product to fasten an iPhone 6 to the windshield inside a car. The suction cup

guarantees secure fastening. The product features a exible support arm for separate

adjustment of the iPhone.

For safety and approval purposes, you must not rebuild and/or modify this product.

If you use the product for purposes other than those described above, the product

may be damaged. Read the instructions carefully and keep them. Make this product

available to third parties only together with its operating instructions.

This product complies with the statutory national and European requirements. All

company names and product names are trademarks of their respective owners. All

rights reserved.

Delivery content

• Car holder

• Operating instructions

Safety instructions

Read the operating instructions carefully and especially observe the safety

information. If you do not follow the safety instructions and information on

proper handling in this manual, we assume no liability for any resulting

personal injury or damage to property. Such cases will invalidate the

warranty/guarantee.

• The device is not a toy. Keep it out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. These may

become dangerous playing material for children.

• Protect the product from extreme temperatures, direct sunlight, strong

jolts, high humidity, moisture, ammable gases, vapours and solvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, take it out of

operation and protect it from any accidental use. Safe operation can no

longer be guaranteed if the product:

- is visibly damaged,

- is no longer working properly,

- has been stored for extended periods in poor ambient conditions or

- has been subjected to any serious transport-related stresses.

• Please handle the product carefully. Jolts, impacts or a fall even from a

low height can damage the product.

• Also observe the safety and operating instructions of any other devices

which are connected to the product.

• Consult an expert when in doubt about operation, safety or connection of

the device.

• Maintenance, modications and repairs are to be performed exclusively

by an expert or at a qualied shop.

• If you have questions which remain unanswered by these operating

instructions, contact our technical support service or other technical

personnel.

Operating elements

1 Holding bracket

2 Star grip nut (not depicted)

3 Support arm

4 Suction cup

5 Suction cup tongue

6 Locking lever

Operation

Choose an installation surface that will not impair your visibility of the road

or cause distraction during driving.

Heed all legal restrictions concerning the use of mobile telephones in

vehicles.

• Make sure that the suction cup and the mounting surface are dry and free from

grease and dust.

• Connect the holding bracket to the support arm. The holding bracket must click into

place audibly.

• If necessary, loosen the star grip nut located at the end of the support arm in order

to rotate or swivel the holding bracket. Then retighten the star grip nut.

• Hold the suction cup to the installation surface and apply a little pressure.

• Push the locking lever toward the installation surface so that the suction cup

adheres to the surface. Make sure that the suction cup is well fastened.

• Place your iPhone in the holding bracket. The two rounded corners of the holding

bracket should be on the left side of the iPhone to prevent covering the camera on

the back. The iPhone must click into place audibly.

• Adjust the iPhone to the desired position using the exible support arm.

• To remove the suction cup from the installation surface, rst lift the locking lever and

then pull the suction cup tongue away from the installation surface.

Maintenance and cleaning

Never use any aggressive cleaning agents or chemical solutions.

• Use a slightly damp cloth to clean the suction cup. Use a mild cleaning agent to

clean o tougher dirt. Allow the suction cup to fully dry before returning it to the

installation surface.

• Use a dry, soft and clean cloth to clean the plastic components. You can use a long-

haired, soft and clean brush and a vacuum cleaner to remove dust.

Disposal

At the end of its service life, dispose of the product according to the

relevant statutory regulations.

Technical data

Operating conditions ................................. 0 to +40 ºC, 0 – 80 % RH

Storage conditions..................................... 0 to +40 ºC, 0 – 80 % RH

Suction cup Ø ............................................. 70 mm

Holding bracket dimensions (W x H) ...... 75 x 140 mm

Weight .......................................................... 91 g

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, e.g. photocopy, microlming, or the capture in electronic data

processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication represent the

technical status at the time of printing.