Instructions

ManualsBrandsRENKFORCE ManualsScannersRF-IDC9277L 2D barcode scanner Bluetooth® 2D, 1D

Quick Guide

- iDC9277L

Before you use scanner, please switch to "C

Charge

mode" and charge inside battery for 3~4 hours first.

* Under “C- Charge mode”, you can raise/lower

soft-keyboard easily.

(For HID profile only)

Before you charge the iDC9277L & smartphone, please

make sure that USB OTG cable connects to smartphone

and set the switch to C (charge mode) first. Then, plug

USB cable into charge port of iDC9277L, the iDC9277L &

smartphone will be charged at the same time.

When in charge, please use the original USB power

adaptor of smartphone (recommended).

When in low battery (Orange LED flashing), please

charge it immediately.

In case the power consumed out totally; the RTC (Real

Time Clock) will back to original setting 01012000.

Attention: Please don’t charge iDC9277L when in Operation

mode. Otherwise, the smartphone’s battery will charge back

to iDC9277L’s battery.

** When pressing Left button + Right button for 8~9 seconds,

iDC9277L will enter deep sleeping mode.

** Please press Left button + Right button + Touch trigger for 8~9

seconds to activate iDC9277L.

** The touch sensor area is around the central area.

Please check the above drawing for your reference.

LED Indicator Information

Orange LED ON Full charged

Orange and Red LED Flashing Charging

Orange LED Flashing Low battery

Red LED ON Off line / out of service

Green LED ON Good read

Orange LED ON Good read (Batch mode)

* Under power-saving mode & deep sleep mode, there will not be

LED indication when charging.

O=Operation mode

C=Charge mode

Left Button

Under BT HID Profile, press Left button to raise/

lower

soft-Keyboard;

press the left button for 4 seconds to

un-pair. Then, scanner can be connected with other

BT devices (Please check page #2, left column)

Touch Trigger Area

SCAN/ Power ON

Press 1 second to wake

up from power saving

mode

Right Button

Power Saving button:

Press the button for 2~3 second

then enter power saving mode

(sleep mode).

Indicator

(LED)

Charge port

Suction Cup

Micro USB cable (OTG)

Connect to micro USB port of

Smartphone in the beginning

Exit

Window

Ion

Battery

inside

Indicator (LED)

PU Glue

(Can be used

repeatedly)

Summary of content (6 pages)

PAGE 1
Quick Guide 3 5 - iDC9277L 1 Suction Cup C=Charge mode Exit Window Left Button Under BT HID Profile, press Left button to raise/lower soft-Keyboard; press the left button for 4 seconds to un-pair. Then, scanner can be connected with other BT devices (Please check page #2, left column) Indicator (LED) PU Glue (Can be used repeatedly) O=Operation mode * Before you use scanner, please switch to "C- Charge mode" and charge inside battery for 3~4 hours first.
PAGE 2
1. click the “Settings” How to Connect to Smartphone 1. 2. 3. HID profile SPP profile a1 Reset Configuration to Defaults (scan from A1 to A4 for HID profile or B1 to B5 for SPP profile) Make sure your device has BT HID or SPP profile Turn off Power-Saving mode on your smartphone first Then, choose HID or SPP profile and scans the following 2 setting codes before connecting to smartphone.
PAGE 3
Trigger Mode There are two operating modes on the scanner Trigger always (You can read the next code, even the data is under transmitting or transmitting completely.) 1.Data Transmission mode (Default) Data read LED It is a necessary to scan “clean memory data" when switching between these two modes. Within 2.4GHz radio range Beyond 2.4GHz radio range Save data into scanner’s memory, Transmit data to PC/terminal scanner will transmit data to PC/ directly terminal automatically when back to 2.
PAGE 4
Date and Time setting Scan the SET DATE barcode, then, scan the six numeric digits in the format mm/dd/yy, from the numeric barcode. For example: “01/23/2011”, please input 012311 SET DATE Scan the SET TIME barcode, then, scan the six numeric digits in the format hh:mm:ss from the numeric barcode.
PAGE 5
1D Symbologies – 2 Barcode Configuration Method: (Flow chart for setup procedure :) Start Configuration ENABLE ENABLE ENABLE EAN-8 DISABLE ENABLE Code 128 DISABLE ENABLE EAN-13 DISABLE ENABLE GS1-128 UCC/EAN-128 DISABLE ENABLE ISSN DISABLE ENABLE MSI DISABLE ENABLE ISBN DISABLE ENABLE CODE 11 DISABLE ENABLE Code 93 ENABLE Codabar DISABLE ENABLE Data Matrix DISABLE ENABLE GS1-Databar (RSS) DISABLE ENABLE QR Code DISABLE DISABLE ENABLE Micro QR Code DISABLE DISAB
PAGE 6
If you want to read the Industrial 2 of 5 (3~5 digital), please read the below setting code to set the Minimum Length to 3 digits ** Back to Default: you can read “HID profile A1-> A2 ->A3 -> A4)” in Reset Configuration to Defaults. (page #2) 1. 2. 3. 4. 5. 6. l Information in this document is subject to change without notice.