Installation Instructions

ManualsBrandsRev-A-Shelf ManualsCabinet Organization & Accessories5" x 36" H Wood pullout Wall Organizer with Soft-Close

INSTALLATION INSTRUCTIONS: 448 SERIES PULLOUT WALL CABINET ORGANIZER W/ SOFT-CLOSE

12400 Earl Jones Way

Louisville, KY 40299

rev-a-shelf.com

Customer Service: 800-626-1126

448 SERIES PULLOUT WALL CABINET ORGANIZER W/ SOFT-CLOSE

TOOLS REQUIRED:

30-45 MIN

ESTIMATED ASSEMBLY TIME:

CARE AND MAINTENANCE:

Clean with a damp cloth and

wipe parts dry.

I-448BBSCWC-0817

THIS UNIT CAN BE INSTALLED IN 2 WAYS

FOR INSTALLATION WITH WOOD SCREWS, TURN TO PAGE 2

FOR INSTALLATION WITH MACHINE BOLTS, TURN TO PAGE 3

WATCH TUTORIALS OF OUR

PRODUCTS BEING INSTALLED

WWW.REV-A-SHELF.COM/VIDEOS

Summary of content (8 pages)

PAGE 1
2400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 448 SERIES PULLOUT WALL CABINET ORGANIZER W/ SOFT-CLOSE TOOLS REQUIRED: 3 8 3 8 3 32 #2 ESTIMATED ASSEMBLY TIME: 30-45 MIN CARE AND MAINTENANCE: Clean with a damp cloth and wipe parts dry. WATCH TUTORIALS OF OUR PRODUCTS BEING INSTALLED WWW.REV-A-SHELF.
PAGE 2
INSTALLATION WITH WOOD SCREWS STEP 1 Flip the unit upside down. Pull the soft-close slide set into the open position and locate the triggers on the left and right side (See Fig 1). Press and hold the triggers either up or down to remove the slide set. Set the wood frame to the side. After you remove the slides, the soft-close mechanism will be in the open position. Press the trigger and reset it to the closed position. STEP 2 FIGURE 1 FIGURE 2 Place the template inside the wall cabinet.
PAGE 3
INSTALLATION WITH MACHINE BOLTS STEP 1 Place the template inside of the wall cabinet. Position the template so the front edge is flush with the front of the cabinet frame (See Fig 1). FIGURE 1 FIGURE 2 STEP 2 With a 3/8” drill bit, drill through the (4) marked hole locations labeled “Pre-drill here for bolt application”. NOTE: Drill through the cabinet floor (See Fig 2). 3 8 STEP 3 Place the unit over the top of the holes and secure using the (4) machine bolts (See Fig 3).
PAGE 4
DOOR MOUNTING INSTRUCTIONS FIGURE 1 STEP 1 Loosen the (4) lock nuts (3/8” wrench) inside the front wall of the unit (see Fig.1). Pull the Adjustable Door Mounting Brackets to ensure that you are mounting to the “thick” portion of the cabinet door. (Front of pullout should line up with front of face frame). NOTE: For measurement locations see Fig. 2. Measure from the base of the face frame up to each mounting bracket slotted hole location and record those dimensions.
PAGE 5
12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 INSTRUCCIONES DE INSTALACIÓN INSTRUCTIONS D’INSTALLATION GABINETE DESPLEGABLE DE PARED DE CIERRE SUAVE CON BALEROS 448 L’ÉLÉMENT COULISSANT AVEC FERMETURE EN DOUCEUR À ROULEMENT À BILLES HERRAMIENTAS REQUERIDAS: OUTILS REQUIS: 3 8 3 32 #2 TIEMPO ESTIMADO DE ENSAMBLE: DUREE ESTIMEE DE L’ASSEMBLAGE: 30-45 MIN CUIDADO Y MANTENIMIENTO: ENTRETIEN ET MAINTENANCE: Limpie con un paño húmedo y seque las partes.
PAGE 6
INSTALACIÓN CON TORNILLOS DE MADERA INSTALLATION AVEC VIS À BOIS PASO 1 ÉTAPE 1 Voltee la unidad 448 boca abajo. Jale el set del deslizante SC dentro de la posición de apertura y ubique los gatillos en los lados izquierdo y derecho (ver la figura 1). Presione y sostenga los gatillos ya sea hacia arriba o hacia abajo mientras al mismo tiempo quita el set del deslizante. Por ahora coloque el marco de madera hacia un lado.
PAGE 7
INSTALACIÓN CON PERNOS INSTALLATION AVEC BOULONS PASO 1 ÉTAPE 1 Coloque la plantilla dentro de la pared del gabinete. Oriente la plantilla para que la orilla del frente esté posicionada a la parte posterior de la puerta del gabinete (ver figura 1). FIGURA 1 ILLUSTRATION 1 Placez le modèle à l’intérieur de votre armoire murale. Orientez le modèle pour que le bord avant soit positionné à l’arrière de la porte de votre armoire (voir l’Illustration 1).
PAGE 8
INSTRUCCIONES DEL MONTAJE DE LA PUERTA INSTRUCTIONS POUR LE MONTAGE SUR LA PORTE PASO 1 ÉTAPE 1 Suelte las cuatro tuercas de seguro (llave de 3/8”) dentro de la pared frontal de la unidad (ver la figura 1). Jale los soportes ajustables del montaje de la puerta para asegurar que usted está montando a la porción “gruesa” de la puerta del gabinete. (El frente del desplegable debe alinearse con el frente del marco).