2400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 WOVEN BASKET WITH RAILS TOOLS REQUIRED: #2 ESTIMATED ASSEMBLY TIME: 20 MIN PARTS LIST CARE AND MAINTENANCE: No. Description Qty. A Wood Rails 2 B Basket Wood Frame w/ Basket 1 Clean with a damp cloth and wipe parts dry. A B WATCH TUTORIALS OF OUR PRODUCTS BEING INSTALLED WWW.REV-A-SHELF.
STEP 1 Measure the inside cabinet width (ICW) at desired height for wood rails (See Figure A). FIG. A Inside Cabinet Width (ICW) Desired Height of Rail STEP 2 Measure the width of basket wood frame (BW) (See Figure B). Subtract BW from ICW. Divide answer by 2. Subtract 1/16” from answer. This will give you the dimension needed from bottom of groove to back of wood rail (ICW-BW) ÷ 2 1/16”. FIG. B Basket Width (BW) STEP 3 FIG. C Cut wood rails per steps 1-3. (See Figure C).
FIG. D STEP 4 Place the first cut rail in the cabinet with the front of the rail against the back of the face frame (for frameless cabinets, flush with front of cabinet.) at desired height. Secure the front hole with proper size screw (See Figure D). Note: Screws not included due to variances in cabinet wall thicknesses. Make sure screw does not go through outside wall of cabinet). #2 STEP 5 FIG.
STEP 6 Measure from the floor of the cabinet to the bottom of the installed rail. Install the second rail on the opposite side of the cabinet per steps 4-5 at height location from step 6. (See Figure F). FIG. F #2 STEP 7 Slide in basket (See Figure G). FIG. G FIG. H STEP 8 Repeat steps for additional baskets (See Figure H).
12400 Earl Jones Way Louisville, KY 40299 rev-a-shelf.com Customer Service: 800-626-1126 INSTRUCCIONES DE INSTALACIÓN / LES INSTRUCTIONS D’INSTALLATION CESTA TEJIDA CON RAÍLES / PANIER TRESSÉ AVEC RAILS HERRAMIENTAS REQUERIDAS OUTILS REQUIS #2 TIEMPO ESTIMADO DE ENSAMBLADO: DURÉE DE L’INSTALLATION: 20 MIN Lista de Parts/Liste des Pièces CUIDADO: ENTRETIEN: Limpie con un paño húmedo y seque las partes. Nettoyer avec un chiffon humide et essuyer pour sécher complètement. No.
PASO 1 / ÉTAPE 1 Mida el ancho interior del gabinete (ICW por sus siglas en inglés) a la altura deseada para los rieles de madera. (Ver la figura A). A (ICW) Ancho interior del gabinete largeur intérieure du placard Altura del carril deseado Hauteur du rail désiré Mesurez la largeur à l’intérieur de l’armoire (ICW) à la hauteur désirée pour les rails en bois (Voir l’Illustration A). PASO 2 / ÉTAPE 2 2) Mida el ancho del marco de la canasta de madera (BW por sus siglas en inglés) (Ver la figura B).
D PASO 4 / ÉTAPE 4 Coloque el primer riel cortado, en el gabinete con el frente del riel en contra de la parte posterior del marco a la altura deseada (para gabinetes sin marco, alinee con el frente del gabinete). Asegure el orificio frontal con el tornillo del tamaño adecuado. (No se incluyen los tornillos, debido a la variante en el grosor de la pared del gabinete) (Asegúrese de que los tornillos no vayan a atravesar la pared exterior del gabinete) (Ver la figura D).
PASO 6 / ÉTAPE 6 Mida desde la parte inferior del gabinete a la parte inferior del riel instalado. Instale el segundo riel en el lado opuesto del gabinete por los pasos 4 y 5 a la ubicación de la altura del paso 6 (Ver la figura F). F Mesurez à partir du bas de l’armoire jusqu’au bas du rail installé. Installez le second rail sur le côté opposé de l’armoire suivant les étapes 4-5 à l’emplacement de la hauteur de l’étape 6 (Voir l’Illustration F).